This Armada XP GP board from Marvell comes with:
* 2GB DDR3 DIMM
* 1GB NAND flash (8-bit interface)
* 16MB NOR flash (16-bot interrface)
* 16MB SPI flash
* SDIO module
* 3 PCIe
* 1 SATA link
* 2 USB EHCI
* 1 internal SSD
* 4 Ethernet Gigabit
* 1 RS232 port over USB
Signed-off-by: Seif Mazareeb
-
Enabling the NAND controller on the mvebu target.
Signed-off-by: Seif Mazareeb
---
target/linux/mvebu/config-3.10 |4
1 file changed, 4 insertions(+)
diff --git a/target/linux/mvebu/config-3.10 b/target/linux/mvebu/config-3.10
index a8cc779..38acc17 100644
--- a/target/linux/mvebu/conf
Hi,
I'm testing your patch with this configuration in /etc/config/network
config device
option name 'ovs'
option type 'ovs'
list ifname 'eth0'
config interface
option ifname 'ovs'
option proto 'dhcp'
However at boot the router enters in an infinite loop:
Decrease the SPI FIFO size in BMC6348 boards to avoid random reads/writes.
The parameter BCM63XX_SPI_MAX_PREPEND is causing the SPI driver exceeds the
hardware capabilities when reading transfer lengths over 58 bytes. Decreasing
the SPI fifo size exactly the BCM63XX_SPI_MAX_PREPEND lenght solve
Hello Gui,
thanks for your report. I just updated odhcp6c to generate the routes
and addresses in netifd in a better way. The old method seemed to have
some races that could lead to the behaviour you have seen. Could you
please retest with the new odhcp6c and see if that works better for you?
Ch
The existing code only tries to split a parition with name "rootfs"
while actually looking for kernel+rootfs, where usually "firmware" is
used as a partition name. This doesn't make sense, as even if there
was a partition 'rootfs' given by mtdparts or via device-tree, this
code would lead to anothe
On 2014-02-02 14:09, Felix Fietkau wrote:
> On 2014-01-31 17:58, Sven Eckelmann wrote:
>> From: Matti Laakso
>>
>> This patch introduces 802.11ac support to base-files, mac80211 and hostapd.
>> The
>> split of VHT160 in two 80 MHz bands is not yet supported, since it requires
>> an
>> additiona
On 2014-01-31 17:58, Sven Eckelmann wrote:
> From: Matti Laakso
>
> This patch introduces 802.11ac support to base-files, mac80211 and hostapd.
> The
> split of VHT160 in two 80 MHz bands is not yet supported, since it requires an
> additional user supplied parameter for the channel of the secon
On Saturday, February 1, 2014 11:13:25 PM "Find Herzfeld"
wrote:
> Did you flash it with the Web GUI? I've managed it fine with a serial
> cable booting into tftp mode or whatever it's called, but the
> default netgear Web interface rejects it.
Thinking on how I did it, what version of the stock
Some ARV4510PW units seem to have unstable PCI due to missing pull-up
resistors. This patch makes sure that the GPIO lines are driven properly.
Signed-off-by: Matti Laakso
---
Index: trunk/target/linux/lantiq/dts/ARV4510PW.dts
===
-
Looks good on my end, although I do get
Sun Feb 2 13:36:49 2014 daemon.notice netifd: radio0 (1935): command failed:
Operation not supported (-122)
Sun Feb 2 13:36:49 2014 daemon.notice netifd: radio0 (1935): WARNING: Variable
'basic_rate' does not exist or is not an array/object
Sun Feb 2 13
Spotted this on my twitter feed, so i guess it is good for something.
http://curl.haxx.se/docs/adv_20140129.html
Signed-off-by: Russell Senior
---
libs/curl/Makefile | 8
libs/curl/patches/100-check_long_long.patch | 2 +-
libs/curl/patches/200-no_docs_tests.p
12 matches
Mail list logo
