In early versions the radials were installed at a 90 degree angle from the
mast. Later versions angled them down at about 45 degrees from the mast.
In all cases they were secured with a band clamp and most installers simply
left them off. The antenna will work just fine without them.
IIRC VHF
Anybody in here know of a retailer in Canada that sells
RG-142U coaxial cable. This is a double shielded cable
that is about the size of RG-58 ?
Thanks
Brad
[EMAIL PROTECTED]
Yahoo! Groups Links
* To visit your group on the web, go to:
would like to paint a cellwave stationmaster...any recommendation as to what would be a fitting paint and where to procure it? thanks chris
Yahoo! Messenger with Voice. Make PC-to-Phone Calls to the US (and 30+ countries) for 2ยข/min or less.
YAHOO! GROUPS LINKS
That
was covered yesterday
SHERWIN-WILLIAMS PRODUCTS:
Etch P60G2 "Wash Primer"
Primer D61H75 "Polane 2.8 Plus Spray Fil"
Top Coat Polane Type "HS 2.8 Plus Polyurethane"
-Original Message-From:
Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED]On
Anyone on the list have any info on this amp?
Tom Saunders
Comm Tech, City of Seattle
Amateur Radio Station N7OEP
206.384.1604
[EMAIL PROTECTED]
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this
Not necessarily answering your question, but RG400 is
the same cable with a stranded center conductor rather
than one solid center conductor. It flexes easier.
Same size and construction. I've seen it for $1/ft but
deals can be found once in a while (100 ft for $60 on
eBay was a good buy).
Bob M.
What is it out of --- so I can know where to go look?
Neil - WA6KLA
Original Message
From: [EMAIL PROTECTED]
To: Repeater-Builder@yahoogroups.com
Subject: RE: [Repeater-Builder] TLE 1062 B
Date: Fri, 24 Mar 2006 08:05:46 -0800
Anyone on the list have any info on this amp?
Tom
Good Day All:
I'm looking for a source for the plastic part that Sinclair uses in
their duplexers for holding the cans to the cross rails. I found
out they call it a 'yoke', but so far have been unsuccessful in
getting a part number or price out of them to order some. (Or an
RMA for a
Anyone can tell me a simple way to tune a small
6 cavity duplexer on 448 - 443 for a VXR-5000
Vertex repeater, never done one before. It's a
Vertex Model DXU B series duplexer that I purchase
with the VXR-5000, this is the same repeater that I'm
looking CSC CWID 51B information about,
Thank you - yes I have the info on that PA Deck.
Motorola Manual Part Number = 68-81008E20
Neil
Original Message
From: [EMAIL PROTECTED]
To: Repeater-Builder@yahoogroups.com
Subject: RE: [Repeater-Builder] TLE 1062 B
Date: Fri, 24 Mar 2006 10:42:01 -0800 (PST)
tle1062 is
Metrum II channel crystals
Motorola Part Number KXN6097AB
ICM Part Number 00162200
You are welcome,
Neil
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this group, send an email
How large is it and is copying feasible?
Tom Saunders
Comm Tech, City of Seattle
Amateur Radio Station N7OEP
206.384.1604
[EMAIL PROTECTED]
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this group,
If you are lloking for just the PA ceck, one or two pages ... if
you are looking for the power supply too, more pages ...
Neil
Original Message
From: [EMAIL PROTECTED]
To: Repeater-Builder@yahoogroups.com
Subject: RE: [Repeater-Builder] TLE 1062 B
Date: Fri, 24 Mar 2006
Does any one know what happened to B D Enterprises? The build low cost
Controllers.
K4SLB
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]
*
Hutton at www.huttononline.com
They have offices in Canada.
-Original Message-
From: Repeater-Builder@yahoogroups.com
[mailto:[EMAIL PROTECTED] Behalf Of bradprimmer
Sent: Friday, March 24, 2006 8:18 AM
To: Repeater-Builder@yahoogroups.com
Subject: [Repeater-Builder] Canadian
At 11:30 AM 03/24/06, you wrote:
Anyone can tell me a simple way to tune a small
6 cavity duplexer on 448 - 443 for a VXR-5000
Vertex repeater, never done one before.
This group has a lot of readers all across the USA,
and in many places in the world, and if you say
where in 1-land you
B D is or was owner and operated by:
Boyd Potts
2871 Monroe St
Santa Clara, CA 95051-1754
(408) 557-9567
Not sure if he is still in business but his repeater
under the callsign kb5jr is still active.
Regards, Barry
--- K4SLB Steve Butler [EMAIL PROTECTED] wrote:
Does any one know what
Dwayne, you are right... The cable length Mst be 1/4 electrical wave
length to come out right just like the ones on your exesisting
duplexer. This is shorter than the calculated wavelength in free
space because the RF propegates slower in coax than free space. You
have to determine the
Does anybody know the tone scheme for the Stardust courtesy tone on
the ACC controllers? It is CT #5 on the RC-85. I have it on my RC-85
and would like to set it up on my RC-850... Thanks for any input.
Andy KC2GOW
Yahoo! Groups Links
* To visit your group on the web, go to:
Andrew,
I found it using google...
http://www.rollanet.org/~joeh/appn4.html
Stardust
E1: 120 ms 750 Hz 0 Hz %Gain =99 0
E2:80 ms 880 Hz 0 Hz %Gain =99 0
E3:80 ms 1200 Hz 880 Hz %Gain =50 0
73
Mike
K5JMP
www.k5jmp.us
-Original
Thanks mike, that is really cool, adding it to my bookmarks. Andy KC2GOW
New Yahoo! Messenger with Voice. Call regular phones from your PC and save big.
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group,
They work good...not as good as a single band antenna,but any dual band
antenna is a compromise. Well constructed with the exception of that
mounting clamp,replace it before you mount it anywhere. 73,Lee
Jim Cicirello wrote:
Hello to Kevin and the group:
I am putting together my 1480
22 matches
Mail list logo
