[Repeater-Builder] Maxar and Moxy Service Manuals - May 2007 List

Here is an updated list of Motorola Maxar, Maxar-80, and Moxy manuals that are still available from Motorola Parts at 800-422-4210. The prices listed are as shown on MOL, but there may be a small surcharge added. Note that several manuals have been added to the original list that was posted on th

RE: [Repeater-Builder] Motorola Board identity

Yes, indeed! If the list isn't too long, just post the board numbers here, and we can help you out. 73, Eric Lemmon WB6FLY -Original Message- From: Repeater-Builder@yahoogroups.com [mailto:[EMAIL PROTECTED] On Behalf Of wesbflyer Sent: Sunday, May 06, 2007 1:31 PM To: Repeater-Builder@

RE: [Repeater-Builder] Re: r100 - eeprom memory map?

OK, Barry - sounds like you're well on your way, then. I have one tuned to 444T5500 and it runs like a champ! 73 de Mark - N9WYS -Original Message- From: Repeater-Builder@yahoogroups.com On Behalf Of Barry Buelow Well I was tryingn to stumble through RSS without much luck. After lookin

[Repeater-Builder] Re: Spectra Tac (Micor) receiver problem?

T J, This is a common problem. The MICOR receiver was desgined with the PL decoder over riding and forcing the UNmuting of the audio. Resulting in very long 'squelch tails'. There is a jumper configuration for the AND squelch function in the manual. Jumpers on the Audio Control Module: JU1 O

Re: [Repeater-Builder] Spectra Tac (Micor) receiver problem?

I had a bad cap on the power supply do that at one time. - Original Message - From: kc8lts To: Repeater-Builder@yahoogroups.com Sent: Monday, May 07, 2007 2:21 PM Subject: [Repeater-Builder] Spectra Tac (Micor) receiver problem? Has anyone encountered this problem with th

Re: [Repeater-Builder] Spectra Tac (Micor) receiver problem?

We have about 19 Spectra-Tac receivers online in our network, here are a few "normal" problems that you should check. 1) The power supply eats the 100uf caps like crazy, especially after 25+ years of use, we change them both as routine maintenance. 2) Likewise, on the audio board the same thing,

Re: [Repeater-Builder] SEITS Web Site

Here ya go... all mirrored up :) http://www.n0trq.com/mirror/www.seits.org/ Any other good candidates for mirroring?? On 5/7/07, Dave Cochran <[EMAIL PROTECTED]> wrote: Easy stuff... I've got a server pulling a copy now.. I'll post a link to the mirrored copy this evening. Dave N0TRQ On

[Repeater-Builder] MSR-2000 VHF Continuous Duty RF PA Manual Scan Available (free of course)

Hello Sailors, I scanned the Motorola MSR-2000 VHF Continuous Duty RF Power Amplifier Service Manual pages into a pdf file for a friend. I can/will send copies out to anyone by simple direct email request. cheers, skipp skipp025 at yahoo.com

[Repeater-Builder] Spectra Tac (Micor) receiver problem?

Has anyone encountered this problem with the Spectra Tac receivers? I have a number of receivers that are having an issue of the squelch being opened up by something in the circuitry ramping up a voltage. Or at least that is what I believe. The problem is that the receiver only has the PL holdin

[Repeater-Builder] Re: Motorola Board identity

The most practical way to ID various Motorola boards might be to snap a picture of the lot and place the picture on the web somewhere. Then ask group members here to view the on-line picture to see if they can id the parts... cheers, skipp > "wesbflyer" <[EMAIL PROTECTED]> wrote: > Is ther

Re: [Repeater-Builder] Motorola Board identity

Also in general, the 4th digit of 1, 2, 3, or 4, will identify the band split within the frequency range, of those bands that are covered by more than one piece of equipment. Usually the parts list in the manual will show the band split range; it varies by model. For example, on the 400-512 MHz ra

Re: [Repeater-Builder] Echolink

I doubt you can buy such a cable. I make all those types of cables myself. -- Original Message -- Received: Mon, 07 May 2007 08:15:47 AM CDT From: "David" <[EMAIL PROTECTED]> To: Subject: [Repeater-Builder] Echolink > anyone now where i can buy a cable to between my echo link board and

Re: [Repeater-Builder] Motorola Board identity

At 01:31 PM 05/06/07, you wrote: >Is there a way I can identify Mot boards from the ink-stamped number on >the board? I have inherited several boards I need to figure out. Most >appear to be RX boards, couple small accessory boards. You can identify at least the frequency range... A third letter

Re: [Repeater-Builder] SEITS Web Site

Easy stuff... I've got a server pulling a copy now.. I'll post a link to the mirrored copy this evening. Dave N0TRQ On 5/5/07, Thomas Oliver <[EMAIL PROTECTED]> wrote: I wonder if someone could mirror their site in case it goes away again. http://web.archive.org/web/20031008124650/www.seits

[Repeater-Builder] Need micor kxn1052 or kxn1019b channel element

for my 'new' repeater. These seem to be a bit scarce. Thank you & 73 Jeff - - NJ5R

Re: [Repeater-Builder] MSR2000 PL Reeds

contact [EMAIL PROTECTED] for reeds he's probably got them. mdm --- "Tony L." <[EMAIL PROTECTED]> wrote: > I need a set of 151.4 (5Z) PL reeds for a > MSR2000 VHF repeater station. > > Please contact me off list if you have a set, > or know a good source. > > Thanks. > > Te

[Repeater-Builder] mobile duplexer for sale

hi friends, there are the custom designed notch type mobile duplexers for sale. You can contact me offline. - Here’s a new way to find what you're looking for - Yahoo! Answers

[Repeater-Builder] DB-4001

Will Decibel DB-4001 cavities tune to 146.0 MHz? Would the coupling loops need to be lengthened? Is this practical? Would three DB-4001 bandpass and three similar looking notch (I assume due to only one UHF connector) cavities make a good duplexer? Pitfalls? Thanks, Joe, W7LUX

Re: [Repeater-Builder] Looking for 146R010 and 146T610 Mitrek elements.

I don't have those particular frequencies, but do have a bunch of the KXN1086 and KXN1088 elements if you want to re-channel some... George, KA3HSW / WQGJ413 - Original Message - From: "maxjam_99" <[EMAIL PROTECTED]> To: Sent: Sunday, May 06, 2007 8:34 PM Subject: [Repeater-Builder] L

[Repeater-Builder] Maxar help!

I managed to bust a tuning slug while aligning a high-band Maxar over the weekend... It's the quadrature detector coil, L18, Moto part number 24-84419D17. Anybody have a spare slug or coil laying around? Or a Maxar carcass I could scavenge off? Or even a working unit you're willing to part

[Repeater-Builder] Motorola Board identity

Is there a way I can identify Mot boards from the ink-stamped number on the board? I have inherited several boards I need to figure out. Most appear to be RX boards, couple small accessory boards.

[Repeater-Builder] Re: r100 - eeprom memory map?

Well I was tryingn to stumble through RSS without much luck. After looking at lots of search hits, I found the 2,4,6,8 keys in an old post on an archive related to BAT's. Just giving credit to a 2002 post by "Will" excerpt: echo KEY Function echo 2 Move down within Menu echo 4 Scroll back echo

[Repeater-Builder] MSR2000 PL Reeds

I need a set of 151.4 (5Z) PL reeds for a MSR2000 VHF repeater station. Please contact me off list if you have a set, or know a good source. Thanks.

[Repeater-Builder] Echolink

anyone now where i can buy a cable to between my echo link board and the rc210 and the computer? see ya 73's N1IB David Schornak K2 03027 www.n1ib.com www.n1ib.com/blog/ www.n1ib.com/leather/ arf don't forget me Mis Ginger Einstein said: "You see, wire telegraph is