On May 22, 2010, at 9:29 AM, Mike Besemer (WM4B) wrote:
> Every Tech Order I ever used in the Air Force started with 'Perform a
> through visual inspection'. Often times, that was good advice.
Thorough, even. ;-)
If you can see through it, the aircraft probably took a few rounds the pilot
di
I used to work for them, they are still active.albeit smaller..Racom
Products 216-351-1755
Doug
KD8B
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com] On Behalf Of mzfb2001
Sent: Sunday, May 23, 2010 5:07 PM
To: Repeater-Builder@yahoogroups.com
Subject:
Yes you can drop the power down on the M1225 radio, but it seams that the heat
stays the same from most of the mobile units.
I always try to look for the LPI radios 5 watt power out and use an external
power Amp..
for my mobile based repeaters.
TPL makes a nice line of PA's also there is a
Thank you Mike, but that scan is the instruction manual not the service
manual.
Milt
N3LTQ
- Original Message -
From: "Mike Morris"
To:
Sent: Thursday, May 20, 2010 12:54 PM
Subject: Re: [Repeater-Builder] OT Looking for service manual Kenwood
TM-733A
> At 08:10 AM 05/20/10, you w
Nate Duehr wrote:
> If you can see through it, the aircraft probably took a few rounds
the pilot didn't know about. ;-)
<--- That reminds me of a story Kevin told about when he worked in a CB
shop.
A guy came in and said he mounted his radio and now it didn't work.
Kevin went out to investi
Mods.dk has a schematic.
Eric Lowell
Eastern Maine Electronics Inc.
48 Loon Road
Wesley ME 04686
eme@starband.net
www.satnetmaine.com
207-210-7469
From: Milt
To: Repeater-Builder@yahoogroups.com
Sent: Mon, May 24, 2010 8:48:33 AM
Subject: Re: [Repeater-B
Scott Zimmerman wrote:
> <--- That reminds me of a story Kevin told about when he worked in a CB
> shop.
>
> A guy came in and said he mounted his radio and now it didn't work.
> Kevin went out to investigate and found the guy drilled two holes right
> straight through the radio and used two lag
I have 3 Quintron low band base stations available; they have a 4-400A
amplifier (350 watt potential), a receiver, control link receiver ( 932 mhz),
digital exciter, control unit (with SWR and metering)and of course, power
supply and a transmitter! They are crystaled now at 46.38 mhz. These
i sent you a service manual did you get it...
From: Milt
To: Repeater-Builder@yahoogroups.com
Sent: Mon, May 24, 2010 8:48:33 AM
Subject: Re: [Repeater-Builder] OT Looking for service manual Kenwood TM-733A
Thank you Mike, but that scan is the instruction m
On 5/24/2010 7:43 AM, Scott Zimmerman wrote:
<--- That reminds me of a story Kevin told about when he worked in a CB
shop.
A guy came in and said he mounted his radio and now it didn't work.
Kevin went out to investigate and found the guy drilled two holes right
straight through the radio and u
On 5/24/2010 11:38 AM, Kevin Custer wrote:
I went out and saw the bolt heads (with nice washers I might add) on the
under side of the case of the radio. He drilled 2 mounting holes right
through both sides of the case (and circuit board) and mounted that
radio to the dash. It sure looked good, a
There were more *commercials* than the actual video - but it was pretty good to
watch.
Don, KD9PT
- Original Message -
From: Nate Duehr
To: Repeater-Builder@yahoogroups.com
Sent: Monday, May 24, 2010 3:25 PM
Subject: Re: [Repeater-Builder] Lost 10 volts in a Master II UHF
I see that your IDer is a model 1300 and mine are model 700, however, I
received this reply from one of Racom's people that may be helpful with
reprogramming any of Racom's IDers:
Snip.
Good Afternoon Jim:
Thank you for the e-mail and your interests in Racom Products.
Generally speakin
The item is still available from pacparts.com. I would recommend checking
the price from an Icom dealer. Part # SC-1056
Jeff
From: Repeater-Builder@yahoogroups.com
[mailto:repeater-buil...@yahoogroups.com] On Behalf Of x.tait.tech get real
Sent: Saturday, May 22, 2010 2:34 PM
To: Repeater-
14 matches
Mail list logo