with this product regardless of band or use.
Thanks to everyone for their advise,
Howard
--- In Repeater-Builder@yahoogroups.com, Jeff DePolo j...@... wrote:
Depending on the PL-259 in question (i.e. who manufacturered it), sometimes
you can get them onto FSJ2 without any problem, other
I ma looking for 2 VHF pre-amps for the MSR2000. The model number is TLD2611A.
If anybody has some I would appreciate knowing about them
Howard K2IMO
hkl...@nc.rr.com
DCFluX,
So, you have placed a standard PL259 on Andrew FSJ2-50 3/8 cable?
Any problems or advise?
Howard
--- In Repeater-Builder@yahoogroups.com, DCFluX dcf...@... wrote:
Yes, I've done it.
On Mon, May 3, 2010 at 7:25 PM, Howard Z howar...@... wrote:
I found some more specs:
fsj1-50a
this with the 1/4 inch FSJ1-50A super flex cable, and not
on the 1/4 inch LDF1-50 hardline cable.
Howard
If this helps, the spec for
LDF1-50 diameter over jacket = 0.345
FSJ1-50A diameter over jacket = 0.290
So assuming the jackets are the same thickness, then LDF1-50 is .055 larger in
diameter than FSJ1-50A.
Howard
--- In Repeater-Builder@yahoogroups.com, Jeff DePolo j...@... wrote:
How
think these cables might be able to use regular PL-259 connectors
without any reducer?
Howard
Some of the MSR2000 had a power supply in them to charge a battewry pack and
when power went out, they would then run off the batteries...there was a
connection on the side of the unit near the antenna connection..So not sure if
you have this type of unit
Howard K2IMO
From a list devoted to the Part 90 narrowbanding issue.
WalterH
-- Forwarded message --
From: nbruark nbru...@gmail.com
Date: Wed, Jan 20, 2010 at 11:44 AM
Subject: [LMR_Narrowbanding] UPDATE - 3rd Party Narrowbanding Kits;
Certification Info
To: lmr_narrowband...@yahoogroups.com
for the
transmitter.
Howard K2IMO
Hello to all and thanks for reading.
I am looking to buy your unwanted Hamtronics R302 receiver for a 2
meter ham application. Would prefer a working radio, but will consider
all, as long as it hasn't been fried by lightning. Please state price
and condition in first email.
Thanks, Howard
W2AFD Howard
First load your repeater ID into one of the blank voice message slots. Then
prigram a schedular to make the controller ID every 15 minutes or what ever
time is needed as required to ID the repeater when not in use.
Howard K2IMO
[EMAIL PROTECTED]
SERA does require that you co-ordinate your control frequency. It will be an
unpublished frequency. Also suggest that you use a sub tone. They will
probably request that anyway.
Howard K2IMO
assuming I
will have to use an attenuator in front of the preamp.
Anyway, any advice on a brand/model of preamp you have used
successfully greatly appreciated.
73 de W2AFD Howard
Looking for a 440 transmitter that puts out about 18 to 20 watts at a
reasonable price. Cannot find a replacement transistor for present
transmitter. Nobody has one. I live in North Carolina
Thanks in advance
Howard K2IMO
--- In Repeater-Builder@yahoogroups.com, skipp025 [EMAIL PROTECTED]
wrote:
Hi Howard,
What's the transmitter you have now and what's the part number
on the bad transistor? Maybe we can help you more than you would
expect...
cheers,
s
Howard Klino hklino@ wrote:
Looking
these freqs for repeaters.
Howard K2IMO
I have read that one should use dual-shielded cables.
Which cables are these?
Is Belden 9913F7 a good choice?
Here is its description: http://www.therfc.com/9913f.htm
What about LDF4-50A coax cable?
Is it a better choice than FSJ4-50B?
Howard
--- In Repeater-Builder@yahoogroups.com, Jeff DePolo [EMAIL PROTECTED]
wrote:
I think this is, or should be, a repeater-builder FAQ.
Foil+braid cables like 9913, LMR-series, etc. should generally NOT
be used
Ok
Andrew FSJ4-50B 1/2 coax cable - best choice - CHECK!
Thanks for the help
Howard
--- In Repeater-Builder@yahoogroups.com, Jeff DePolo [EMAIL PROTECTED]
wrote:
I think this is, or should be, a repeater-builder FAQ.
Foil+braid cables like 9913, LMR-series, etc. should generally
Group,
I am looking for a repeater application that runs on the 68hc11
microprocessor. Can anyone advise further?
Thanks,
Howard, N3FEL
Bensalem, PA
USA
Yahoo! Groups Links
* To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
* To unsubscribe
21 matches
Mail list logo