[Repeater-Builder] Old style 7/8th inch heliax

I have a roll of Andrew 7/8th inch heliax with an outside spiral wrap insulated. I am told that the new 7/8th inch heliax (concentric rings) connectors (L45N and L5PNF) won't fit the old style heliax. What type do I need? I would like to terminate with a type N female. Thanks de David

[Repeater-Builder] Andrew L45N and L45Z

Does anyone have a source for the following connectors: L45NI need at least four L45ZOne will do These type of connectors fit the old style 7/8 inch heliax. Contact me at: drwoolwea...@yahoo.com Thanks de David

[Repeater-Builder] Tower cost?

Fellows: How much are seven sections of used Rohn 45 tower worth? The tower is on the ground, has been painted, but the galvanized appears to be intact...no rust. No bent sections. Estimates? Thanks de David

[Repeater-Builder] Emergency Power

Does anyone have a circuit to the reduce the power output of a VHF GE MASTR II repeater station when primary power is lost? I searched the messages and found some comments, but no circuit. Recommendations? David

[Repeater-Builder] GLB VHF Pre-amp

Does anyone know the transistor type used in GLB VHF Preselector preamps? Thanks de K5RAV.

[Repeater-Builder] GE MASTR II Station power supply

Fellows: How can I tell if my VHF MASTR II Station power supply will run a 110 watt repeater? I understand that the lower powered repeaters had smaller supplies? Right? Are all the supplies the same? de David

[Repeater-Builder] GE MASTR II

I need to buy six MASTR II power cords. I only need the plug and the red/black wires. Also need mobile mounting trays. How much? Thanks de David

[Repeater-Builder] Cooling fan relay circuit?

My club has several ACC controllers and none have provided for cooling fan control. Does anyone have a simple circuit to turn on a fan with PTT and then keep it running for xx minutes after PTT is released? The repeater PTT line goes to ground on transmit. Most of the NE555 timer circuits that

[Repeater-Builder] HF Remote Base?

Any suggestions for a modern repeater controller that will also operate a frequency agile HF remote base? Thanks de David

[Repeater-Builder] Uniden SMH 400G

Does anyone have a programmer for a SMH 400G? Thanks de David Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is

[Repeater-Builder] GE MASTR II Audio problem

My club has a GE MASTR II mobile modified repeater controlled by an ACC96. The ACC96 has a small satellite board plugged into socket U33 on the right side of the main board. There are two chips on the board: SN74HC74N and PAL10L8NC. Transmit audio is good going to the small satellite board, but f

[Repeater-Builder] Uniden SMH 400G

Just acquired an Uniden SMH 400G VHF radio. Did a Goggle search without results. Anyone have info on this VHF radio? Does it have programmable frequency, PL encode/decode? Thanks de David Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/

[Repeater-Builder] VHF Splitter

Ham club wishes to use one VHF receive antenna for three different VHF receive systems. Two VHF repeaters and one packet digit. Any suggestions on how this can be done and where is the best place in the antenna system to install a preamp? Transmitters are combined and use separate antenna.

[Repeater-Builder] TKR820

Does anyone have a source of the special molex plug for the back of a Kenwood TKR820? Thanks David [EMAIL PROTECTED] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to:

[Repeater-Builder] RG400 or RG214/U

Anyone know a source of RG400 or RG214/U? I need short runs to build duplexer cables. Does a PL259 fit these cables? Thanks de David [EMAIL PROTECTED] Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe

[Repeater-Builder] ACC96

I am trying to configure an ACC96/VHF GE MASTR II to encode on COS. The 96/repeater presently decodes 114.8 PL and the 96 also controls a UHF link radio. Any hints from those go before me? Pin outs? Thanks de David Yahoo! Groups Links <*> To visit your group on the web, go to: h

[Repeater-Builder] Kenwood TKR-820 UHF

I recently acquired a TKR-820. Is it possible to program repeater to encode on COS? Is there a time out timer adjustment? I saw a note about time out alarm, but nothing about timer adjustment. Thanks in advance. David Yahoo! Groups Links <*> To visit your group on the web, go to:

[Repeater-Builder] Back up battery

Anyone have experience with gel cell batteries made for the popular electric scooters? I found a 12VDC 12aH deep discharge battery for $16.50 shipped. Comments? de David Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/

[Repeater-Builder] Fan control

Anyone have a parts list for thermal control of 12VDC fan? Thanks de David Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Y

[Repeater-Builder] Fan controller

I need a simple circuit for a repeater PA fan controller with delay time out. I did a search, but found nothing. Thanks de David Yahoo! Groups Links To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ To unsubscribe from this group, send an email to:

[Repeater-Builder] SS Hardware?

Anyone know a cheap source for SS hardware? Bolts, nuts, washers, etc. Thanks de David, K5RAV Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/