On Tue, Oct 7, 2008 at 9:24 AM, Tonix (Antonio Nati)
<[EMAIL PROTECTED]> wrote:
> General question to developers:
>
> which are usually problems which make PF sense failover to anoter unit?
The most common cause of failing over when it shouldn't is switches
that hose or block multicast.
> Can an
That's a pretty helpful log message. Looks like you declared a failover
peer incorrectly. Please review your configuration with that in mind.
Matias Surdi wrote:
Hi,
I'm using pfSense 1.2 , and suddenly DHCP seems to have stopped
working. On the system log, i see the following:
Oct 7 22:2
Hi,
I'm using pfSense 1.2 , and suddenly DHCP seems to have stopped working.
On the system log, i see the following:
Oct 7 22:23:34 dhcpd: Internet Systems Consortium DHCP Server V3.0.5
Oct 7 22:23:34 dhcpd: Copyright 2004-2006 Internet Systems Consortium.
Oct 7 22:23:34 dhcpd: All rights r
ok
Strange -
Mine shows snort (running) but not ntop ...
go figure :-)
glenn
On Oct 7, 2008, at 7:16 AM, Sean Cavanaugh wrote:
1.2 or 1.2.1 full install both run snort and/or ntop. embedded image
does not support packages. Also if the package is marked as broken,
then it will not be list
Sure i am very careful on the VHID.
It had causeme a lot of trouble because of the duplicated VHID
Also i had a weird experience on the CARP name.
I have a lot carp name which will be duplicate when there are more than 56
CARP VIP.
Let 's say
carp56 192.168.10.56
carp0 192.168.10.57
carp58 192.1
General question to developers:
which are usually problems which make PF sense failover to anoter unit?
Can an intense CRC problem cause a failover, or only a link down state
can make this happen?
Tonino
frankie wong ha scritto:
Dear all,
I have found pfsense a very nice opensource firewall
frankie wong wrote:
> Thanks Paul
> Yes i do have a dedicated sync interface
> Both of the WAN and LAN interface are connected to a cisco 3750 switch
> I also have the port-mirroring on the WAN link for my IDS
> I may check out the speed/duplex config on the switch to see
>
>
we don't have as m
Thanks Paul
Yes i do have a dedicated sync interface
Both of the WAN and LAN interface are connected to a cisco 3750 switch
I also have the port-mirroring on the WAN link for my IDS
I may check out the speed/duplex config on the switch to see
Frankie
On Tue, Oct 7, 2008 at 8:37 PM, Paul Mansfie
do you have a dedicated sync interface?
what kind of switch are you connected into - I've seen problems a bit
like this when the pfsense NICs were set to auto speed/duplex but the
ISP has them fixed
-
To unsubscribe, e-mail: [E
Dear all,
I have found pfsense a very nice opensource firewall since half-an-year ago.
After intensive digging at google and testing, i had decided to migrate the
firewall to pfsense.
And it always looks good, failover are always smooth and without service
interruption.
However problem arise sinc
1.2 or 1.2.1 full install both run snort and/or ntop. embedded image does not
support packages. Also if the package is marked as broken, then it will not be
listed in the package list as available for install ( I believe snort was still
marked as broken, havent checked in a while)
From: [EMAIL P
Coming late into this thread, I think I can add some salt to it :)
I have the exact same problem to one of the sites, one I actually worked for
two years ago, so I know about the setup there.
At home I have pppoe to ISP and pfsense 1.2.1, problematic site has (probalby
still) pfsense 0.9.6 and
12 matches
Mail list logo
