Re: [time-nuts] Resampling/decimating (was: Frequency standards for different tau in Allen Dev measurement)

It is there, but briefly... http://www.dspguide.com/ch3/6.htm You have to look for 'multirate'. On Mon, Feb 24, 2020 at 9:41 PM Gary E. Miller via time-nuts < time-nuts@lists.febo.com> wrote: > Yo Poul-Henning! > > On Mon, 24 Feb 2020 16:26:09 + > Poul-Henning Kamp via time-nuts wrote: > >

[time-nuts] For Sale: PRS-10

For sale: One new PRS-10 which has been in storage in original anti-staric bag for a couple of years. Bag has never been opened. Basic PRS-10, no options. Asking $800 + shipping to CONUS address. Please reply off list. -Brian ___ time-nuts maili

Re: [time-nuts] Resampling/decimating (was: Frequency standards for different tau in Allen Dev measurement)

Yo Poul-Henning! On Mon, 24 Feb 2020 16:26:09 + Poul-Henning Kamp via time-nuts wrote: > >> Anyone have any references to how to decimate properly? > > I can highly recommend this free book: > > http://www.dspguide.com/ The words "decimate" and "decimation" do not apear in that bo

Re: [time-nuts] A simple sampling DMTD

It turns out Bobs dumpster was my dumpster by a long path. I still have the sampling HP54100 1 Ghz scope and it works. Many other lucky bits to get. Best regards Paul WB8TSL On Mon, Feb 24, 2020 at 1:43 PM Bob kb8tq via time-nuts < time-nuts@lists.febo.com> wrote: > Hi > > Yup, welcome to the onl

Re: [time-nuts] A simple sampling DMTD

Hi Yup, welcome to the online auction lottery ….. As you may have noted, I’m struggling a bit with the Phase Station and random (likely my fault) issues. At the same time, I’m going around in circles about the R&S FPC-COM2. It’s a pile of money, but it would replace a lot of questionable gear I h

Re: [time-nuts] A simple sampling DMTD

I woke up this morning, check my HP105B, it's absolutely going nuts.  Heater temp down, frequency ALL OVER the place.  No output in any of the ports.  Sigh.  eBay strikes again! --- (Mr.) Taka Kamiya KB4EMF / ex JF2DKG On Sunday, February 23, 2020,

Re: [time-nuts] A simple sampling DMTD

I took over master bedroom for my lab, and I have a gate for dog entry prevention.  All cables are over-head.  I need protection from 2 legged and 4 legged variety. --- (Mr.) Taka Kamiya KB4EMF / ex JF2DKG On Monday, February 24, 2020, 10:47:20 AM EST,

Re: [time-nuts] Resampling/decimating (was: Frequency standards for different tau in Allen Dev measurement)

In message <20200224172030.8fe69e686dfb1c2f08b7a...@kinali.ch>, Attila Kinali via time-nuts writes: >On Fri, 21 Feb 2020 12:09:53 -0800 >"Gary E. Miller via time-nuts" wrote: > >> Anyone have any references to how to decimate properly? > >(Disclaimer: This is not my forte and I only know

[time-nuts] Resampling/decimating (was: Frequency standards for different tau in Allen Dev measurement)

On Fri, 21 Feb 2020 12:09:53 -0800 "Gary E. Miller via time-nuts" wrote: > Anyone have any references to how to decimate properly? (Disclaimer: This is not my forte and I only know the basics, so take with a grain of salt) The basic way is to filter the input signal through a band-pass or low-p

[time-nuts] eLORAN on at 1100 East GRI is 99600

Receiving eLORAN that I believe is using Helen Systems modulation. SRS-700 locked fine. Regards Paul WB8TSL ___ time-nuts mailing list -- time-nuts@lists.febo.com To unsubscribe, go to http://lists.febo.com/mailman/listinfo/time-nuts_lists.febo.com and f

Re: [time-nuts] A simple sampling DMTD

Hi …… looking at the data this morning. It appears that in my case *somebody* (I’m blaming the dog) must have bumped the setup. There is a very obvious set of steps in the phase data. The overnight run has no similar steps. Sometimes getting everything away from the test is a good thing ….. Bo