hi All,
I'm using simpleTime component with Time and TimeUtils interfaces. Is it
possible to measure time intervals less then 30ms? Under this time
difference I can get no measures.
thank you
roberto
___
Tinyos-help mailing list
Tinyos-help@Millennium.
For example, let's say we have 2 motes. Mote 0 is transmitting 0s all the time, so transmitting[5] = 0, radio_active[0] = 0, and radio_active[1] = 0.While mote 0 is transmitting 0s, the TOSH_rfm_rx_bit() in TOS_SIGNAL_HANDLER(SIG_OUTPUT_COMPARE2B, ()) of mote 1 is called. And because radio_active[1
Hi all,
We have problem with our MIB510, and I think it is not matter of syntax in
writing the command in the bash shell. We will appreciate if somebody has
suggestions.
We have a MICA mote kit (the professional one) consisting of a programmer
MIB510 and some motes (mica2 and mica2dot). We
Hi,
Are you using COM4 (/dev/ttyS3) with MoteView,too? (The installer seems
to try using that). Is your bash command complete? The correct command
should be
$ make mica2 reinstall,0 mib510,/dev/ttyS3
Another thing is, some motes are quite reluctant to accept programming,
many times I must give t
Hello,
I want to use TPSN protocol for my project. I downloaded the code from
your site and tried implementing it on tinyos 1.1.15 (for tossim). I got
the following error:
[EMAIL PROTECTED] TestTPSN]# make pc
compiling TestTPSN to a pc binary
ncc -o build/pc/main.exe -g -O0 -board=micasb -p
Hi all,
Thank you, for the answers.
We did many things including: different commands including
"MIB510=/dev/ttyS0 make mica2 install" and ". mib510,/dev/ttyS3", switching
the button in ON position, testing with serial RS232 cable instead of
USB-to-RS232, testing with 4 different motes, etc.
I measured the throughput of Mica2 and get a result of 12 packets/second, and 29 bytes per packet limited by BMAC. Could I improve the throughput by increase the packets rate or packet size?
Feel free to call! Free PC-to-PC calls. Low rates on PC-to-Phone. Get Yahoo! Messenger with Voice
Hello, I had a similar problem: the programmer did not respond although TOSBase could receive and send message from and to the pc/networkHowever, the motes could not be reprogrammed. I identified the problem: the motes were not getting enough power to program them. There was something wrong with th
This problem can be caused by the mote not sitting well on the programmer.
You may need to exert some pressure to make sure the mote is well
connected to the programming board.
Adesola
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Tsenka
Stoyanova
Sent
Hi, allI am trying to send a packet from a PC to a micaZ mote through serial cable. The packet looks like:7e 42 ff ff 0 81 10
f f f f f f a1 21 7e header data crc
(I put two random bytes in the crc field, but I think that's not a big problem since it doesn't filt out CRC-error p
Hello everyone,
For some reason we can't get TOSSIM run properly the once we load tinyviz the motes are present however they are not doing anything, there seems to be no communication or anything. Is there something wrong with the TestTinyViz App?
attached is some of the outputs that we reci
I have formatted my flash in tinyos1.x using the TEstNewFlash format
application. Now Im trying to call mount.mount in my boomerang
application. It is not mounting.
Do I need to format the flash using "make tmote". but TestNewFlash
doesnt seem to be working in boomerang.
Is there any work around..
Hi, All: Can anyone help me with the the xbow MTS400 problem. When I receive the packet, the packet length is changing, sometimes is 40 bytes and sometimes is 39 bytes. I found a dump(0xd5) byte is inserted in to message? Can anyone tell me how to make the packet to be accordance, not changin
Hi Lei,
Are u trying to send the packet to Micaz using serial Forwarder and
Broadcast Inject. If not, What format are u using to send it???
Note: 10 represents the data length right?? so I think it should be 6 and
not 10. Also, since you are sending the packet to the UART so the
destination addre
Hello,
I've installed tinyos and all the extensions. When I compile make pc or make telosb it creates the correct files.
When I try to install I get the following error. i'm using Windows xp / cygwin
$ make telosb installmkdir -p build/telosb compiling Blink to a telosb binaryncc -o bui
You should be able to compile
/opt/tinyos-1.x/apps/TestDeluge/FormatFlash
with
make tmote
-Joe
On 6/5/06, jagan nath <[EMAIL PROTECTED]> wrote:
I have formatted my flash in tinyos1.x using the TEstNewFlash format
application. Now Im trying to call mount.mount in my boomerang
application. It
Does anyone know of any replacements for tinyviz?
___
Tinyos-help mailing list
Tinyos-help@Millennium.Berkeley.EDU
https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
@Millennium.Berkeley.EDUMessage-ID:<[EMAIL PROTECTED]>Content-Type: text/plain; charset="us-ascii"An HTML attachment was scrubbed...URL: http://mail.millennium.berkeley.edu/pipermail/tinyos-help/attachments/20060605/749653e2/attachment-0001.html--Message:
i < tos_state.num_nodes; i++) {> radio_active[i] += bit;> }> }>>> Regards,> Haibin>-- next part --An HTML attachment was scrubbed...URL: http://mail.millennium.berkeley.edu/pipermail/tinyos-help/attachments/20060605/157e2afc/attachment-0001.html-
The mica2 and micaz _are_ Atmega128's so no porting should be necessary.
Or do you want to run TOS on your own '128 board? If so, then I'd guess
that anything that doesn't use the radio or EEPROM chips would work
pretty straightforwardly. You'd need to compare the schematics to
see if there are an
You may be seeing an 'escape' char that preceeds a 0x7d (I think
that's the value that's escaped). See this for details:
http://weblog.cs.uiowa.edu/294s05-project/uart/slides/deciphering-serial-packets.pdf
MS
Zhengsu Gao wrote:
Hi, All:
Can anyone help me with the the xbow MTS400 problem
Hi , I am collecting data info using XSensorMDA500 on 3 different mote nodes and send them to a base station. And on base staion , I changed the TOSBase to calculate the average value of each three. But the average can not been successfully gotten and shown throught Xlisten. Take temerature fo
I think you are saying that the Xlisten program doesn't receive
any packets from the modified TOSBase? It may be because the
crc value in the packet is not correct and Xlisten is throwing it
away. Do you get anything if you use ListenRaw (which
just grabs chars from the port and attempts to sync w
Hi,
I was wondering whether there are any modules that create the neighbor list and can be accessed.
Thanks
Kn
___
Tinyos-help mailing list
Tinyos-help@Millennium.Berkeley.EDU
https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
Hi, JuliaThanks for your reply.I was using a general serial-port application to send data to the mote, because I want to have my own application to control motes.My steps:Firstly, I created a data file with TOS_Msg type; then the application read it and sent data to the base mote through serial por
Lei,
you're actually right.
You need to write to the 7E address.
Try sending this message:
7E42 7D5E 7D5D 05AA 0744 0811 3840 7E
Sankar.
On Mon, 05 Jun 2006 23:23:41 -0500, Lei Tang <[EMAIL PROTECTED]> wrote:
Hi, Julia
Thanks for your reply.
I was using a general serial-port appli
I am trying to print RSSI strength in the recieved broadcast packet. First
i was trying to access in tinyos-1.0 but i came to know that it is not
possible in this version. I upload my tinyos to 1.15 but i am getting the
value as zero only. Has ne one else came thru similar problem?
-rajat
_
of course, i'm assuming you're using a windows based PC and are using a
generic serial port access software (MATLAB, java etc.) to write to the
serial port.
Sankar.
On Mon, 05 Jun 2006 23:35:30 -0500, Sankar Gorthi
<[EMAIL PROTECTED]> wrote:
Lei,
you're actually right.
You need to wri
i was able to get it. what seems to be the problem?
all i did was access the message->strength value.
Sankar.
On Mon, 05 Jun 2006 23:33:52 -0500, Rajat Bansal <[EMAIL PROTECTED]>
wrote:
I am trying to print RSSI strength in the recieved broadcast packet.
First i was trying to access in
On May 30, 2006, at 7:07 PM, Joe Polastre wrote:
Phil Levis can correct me on this, but Phil's ASVM (Mate) runs on
Tmote Sky from Moteiv (my company, www.moteiv.com).
It runs on both the mica (mica, mica2, micaZ) and telos (Telos revA,
Telos revB, and TMote) families. When compiling for the
By the use of "print" I think you may be trying to get the strength
on the host PC? If so, it ain't there. It's only available in the
TOS_Msg structs on the mote end of the world, and is not passed
over the UART to the host.
Search back on this list for "RSSI" discussions.
MS
Rajat Bansal wrote
dear sanskar,
1) which version of tinyos did u use?
2) i am attaching my code for recieved packet.
event TOS_MsgPtr ReceiveIntMsg.receive(TOS_MsgPtr m) {
TOS_MsgPtr ret = m;
IntMsgnew*message = (IntMsgnew *)m->data;
atomic{receivednode=message->src;}
// call ADC.getData();
// call ADC
well,
this is my (a colleague's) code:
Receive.receive(TOS_MsgPtr m)
IntMsg *message=(IntMsg*)buffer.data;
message->val=m->strength;
doesn't look too different.
although our experiments were done on the actual motes and we broadcast
the value in a message packet as you can see.
Sankar
and oh - tinyos-1.1.0
Sankar.
On Tue, 06 Jun 2006 00:20:08 -0500, Sankar Gorthi
<[EMAIL PROTECTED]> wrote:
well,
this is my (a colleague's) code:
Receive.receive(TOS_MsgPtr m)
IntMsg *message=(IntMsg*)buffer.data;
message->val=m->strength;
doesn't look too different.
although our
okay i got it..i think tossim seems to be the problem. I also read it
somewhr that there is some problem with printing the strength value on pc.
Thanks,
Rajat
On Tue, 6 Jun 2006, Sankar Gorthi wrote:
and oh - tinyos-1.1.0
Sankar.
On Tue, 06 Jun 2006 00:20:08 -0500, Sankar Gorthi <[EMAIL
But according to tossim document, the "simple" radio model places all nodes in a single cell and every bit transmitted is received without error. So it should not have any hidden station problem.The thing is every time node is transmitting 0s, it is considered not transmitting. That's the part that
well,
makes sense doesn't it? how can you simulate the strength of the recieved
signal? i'd imagine it's fairly random.
although, i wouldn't stake anything on it. maybe someone else has a better
idea.
Sankar.
On Tue, 06 Jun 2006 01:33:41 -0500, Rajat Bansal <[EMAIL PROTECTED]>
wrote:
I used telosa,but i can't compiler in Tinyos-2.x.
what can i do?
___
Tinyos-help mailing list
Tinyos-help@Millennium.Berkeley.EDU
https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
38 matches
Mail list logo