By the way, Carl, you indicated that whe you were tapped at 90', the real part was 60 ohms when you tuned ou't the series reactance with th;e series capacitor!!
Gee!! That ain't a bad match!! Should result in about 1.2:1 VSWR when fed with 50 ohm cable!! Not bad at all and certainly not enough VSWR to cause any significant excess loss (over "flat-loss") even on a very long run of coax feeding the gamma match!! You were essentially done at that point and you should have just stopped there and bolted everything down!! You could probably find the 50 ohm j0 tap point somewhere below 90 ' , but if those are the only four tap points that are available, then 90' is the one that you want! The 14 ga wire isn't causing "goofy" readings and your radial field is probably OK as well! ("operator head-spacing problem"??) GL - move the tap back to 90' and be done! And you can't do a gamma match to shunt feed that tower without a series-c in the gamma arm! No way! 73, Charlie, K4OTV -----Original Message----- From: Topband [mailto:topband-boun...@contesting.com] On Behalf Of Carl Braun Sent: Friday, February 14, 2014 6:15 PM To: '160' Subject: Topband: Still in search of resonance List Some of you may have followed my efforts in trying to shunt feed my 90' Tri-Ex Skyneedle with 20 meter yagi at 93'. I'm still unable to find any sort of resonance point on the tower. To refresh everyone's memory here are the specifics: 90' Skyneedle that is 12" round at the base and 4" round at the top 13' of mast out the top 5 element Telrex 20M monobander mounted at the 93' level. No other antennas on the tower 1 ½" copper pipe as a radial ring that surrounds the concrete base that measures 4' x 8' rectangle. Three 8' ground rods are connected to the radial ring via 1" copper strap that is .125 thick. Currently I have 27 14AWG insulated wire radials. Most of the radials are 20' to 50' long with three at 90 to 120' long and four of them connected to my 40M vertical array which have 100 count radials 50' to 100' each. The tower is grounded to each ground rod via 1" copper strap .125" thick and, as mentioned above, the ground rods are connected to the radial ring with the same strap with copper clad stainless screws. When I bolted the gamma arm to the tower at the 90' height I dropped a single 14AWG wire to the ground where my FLUKE meter read ZERO ohms between the radial ring and the end of the gamma wire with no fluctuations so I'm confident that I have good continuity throughout the tower. Here are the readings that I saw on the MFJ analyzer with the gamma arm mounted at the (4) points on the tower that are available... With the gamma arm mounted at 90' and 36" spacing I saw 425 ohms at the end of the drop wire on the MFJ With the gamma arm mounted at 67' and 36" spacing I saw 380 ohms at the end of the drop wire on the MFJ With the gamma arm mounted at 46' and 36" spacing I saw 240 ohms at the end of the drop wire on the MFJ With the gamma arm mounted at 28' and 36" spacing I saw 120 ohms at the end of the drop wire on the MFJ At all of these points I was able to knock down the R with my honkin' 1050pf cap to some resonance sort of resonance at 1.825 MHz but, as most everyone has indicated, I should be able to find a 50 ohm tap somewhere on the tower. I can't find it. When I had the gamma arm mounted at the 90' level. I was able to put my baby variable 160pf inline to bring the 425 ohm impedance down to about 60 ohms and the antenna heard very well; especially on the 1700 KHz broadcast band, with a 2.4:1 Vswr. Similar results could be seen at the other levels too as long as I brought the R down with a variable cap. Yesterday, with the gamma arm at the 46' level (and 240 ohms on the MFJ) I was able to put the big variable inline to bring the reading to 24 ohms with a TRUE X=0. With a 22 ohm to 50 ohm UNUN, I saw 1.3:1 Vswr on the output of the UNUN. I worked a W2 in NJ and a W4 in Florida with just the 1000D. BUT...again...I'm bringing the R down with the capacitor...not finding 50 ohms anywhere on the tower. Is my radial field so poor that I'm seeing these goofy readings? Is the single 14AWG too thin causing goofy readings? I'm back to scratching my head. Comments from the list? Carl AG6X _________________ Topband Reflector Archives - http://www.contesting.com/_topband _________________ Topband Reflector Archives - http://www.contesting.com/_topband