[U-Boot] [PATCH] doc: uniphier: add simple guide to Verified Boot

Add a simple documentation about how to use the Verified Boot on UniPhier boards. Signed-off-by: Masahiro Yamada --- doc/README.uniphier | 227 +++- 1 file changed, 226 insertions(+), 1 deletion(-) diff --git a/doc/README.uniphier b/doc/README.un

Re: [U-Boot] ZynqMP qspi

Hi Siva, On 26/09/17 01:28 AM, Siva Durga Prasad Paladugu wrote: > Hi, > ... > > I am planning to send the new series in 1-2 weeks, probably you can wait till > then or > you can try with the patch[2] and see if you are able to get it working with > those( those > are known to be working when

Re: [U-Boot] [PATCH] ARM: imx6: Enable UMS and DFU on DHCOM i.MX6 PDK

Hi Marek, > Enable UMS and DFU, so that the eMMC can be accessed via the > USB gadget port on the board. > > Signed-off-by: Marek Vasut > Cc: Stefano Babic > --- > board/dhelectronics/dh_imx6/dh_imx6.c | 10 ++ > configs/dh_imx6_defconfig | 8 > include/configs/dh

[U-Boot] [RFC] Attempt to Add SPL Support to imx6q_logic

The Logic PD i.MX6 dev kit is capable of SPL. This patch follows a similar method as the mx6sabresd Following instructions I found which show to put the SPL and .img files on the SD card with dd. sudo dd if=SPL of=/dev/xxx bs=1K seek=1; sync sudo dd if=u-boot.img of=/dev/xxx bs=1K seek=69 I wou

Re: [U-Boot] [PATCH v3 1/2] sunxi: Enable THUMB build for the U-Boot binary

On 20/10/17 13:16, Maxime Ripard wrote: > We start to get to the limit of our main U-Boot binary size (with some > boards even crossing it). Enable its build using thumb2 to get some extra > room. > > Suggested-by: Siarhei Siamashka > Signed-off-by: Maxime Ripard I quickly boot tested this on a

Re: [U-Boot] [PATCH] omap2: nand: Make NAND_OMAP_GPMC_PREFETCH default

Hello Tom, On 10/20/2017 10:55 PM, Tom Rini wrote: This option provides better performance and should really always be enabled. Make this be default y. Right, for the 8 bit / 16 bit this should work. At least two years ago, so assuming you guys didn't brick it in the mean time: Acked-by: Je

[U-Boot] [PATCH] MAINTAINERS: Add missing boards and config entries

As part of my usual round of build testing, output about missing MAINTAINERS information was not logged, and thus often overlooked. Correct that mistake by ensuring that I log the output of genboardscfg.py every time. As part of that, address a number of missing MAINTAINERS entires. In the case o

Re: [U-Boot] [RFC] mmc: fsl_esdhc: Do not set high speed mode on MX25 and MX51

Hi Benoît, On Sat, Oct 21, 2017 at 10:34 AM, Benoît Thébaudeau wrote: > I already have a mainline version working at HS with changes only in > fsl_esdhc.c (apart from the port of my board). I still have to narrow > these changes down to the issue. Ok, great! > Is it mainline Linux that you hav

[U-Boot] [PATCH] ARC: HSDK: Fixup DW SDIO CIU frequency to 50000000Hz

DW sdio controller has external ciu clock devider controlled via register in SDIO IP. Due to its unexpected default value (it should devide by 1 but it devides by 8) SDIO IP uses wrong CIU clock (it should be 1Hz but actual is 1250Hz) and works unstable (see STAR 9001204800) So increas

Re: [U-Boot] [RFC] mmc: fsl_esdhc: Do not set high speed mode on MX25 and MX51

Hi Fabio, On Fri, Oct 20, 2017 at 8:40 PM, Fabio Estevam wrote: > On Fri, Oct 20, 2017 at 10:40 AM, Benoît Thébaudeau > wrote: > >> With mainline U-Boot on my board, normal-speed SD cards work fine, but not HS >> ones. Both types of cards work fine at 48 MHz with my custom and older >> U-Boot.

[U-Boot] [PATCH] ARM: uniphier: remove verify=n from environments

If the environment "verify" is set to n, the image verification is entirely skipped. Remove it as a preparation for verified boot. Signed-off-by: Masahiro Yamada --- include/configs/uniphier.h | 1 - 1 file changed, 1 deletion(-) diff --git a/include/configs/uniphier.h b/include/configs/uniph