I've set pCP/jivelite to return to the NowPlaying screen after x seconds
without interaction (is it called the screensaver setting?).
And I've noticed that this 'screensaver setting' doesn't apply to the
NowPlaying's current playlist screen - which makes sense.
Do you think you could add anothe
epoch1970,
I reflashed the SD card to pCP 7, 32 bit, installed in a rP1 4b and went
through the updates and setup and it works as you said.
Once more the 64 bit pCP 7 is not quite up to speed (my Allo Boss2
initially needed pCP 7 32 bit to work) no big deal.
>From a former life in IT project man
Hi,
I had a pcp6 on a Zero with Pirate Audio that I upgraded to pcp7.0.0
today. Some additional tweaks that weren't obvious to me.
Rotate screen: in config.txt (see 'instructions in post 348'
(https://forums.slimdevices.com/showthread.php?111502-Jivelite-on-a-Pirate-Audio-240x240-screen&p=9719
Wirrunna wrote:
> Well, I can't get AP to work.
> My understanding of Bridge Mode is that it will take the network range
> via the ethernet cable, so shouldn't the AP IP Address be greyed out if
> Bridge Mode is Yes ?
You're correct.
There is a glitch in the matrix, you should just disregard the
Paul Webster wrote:
> Starting LMS is not needed.
> That is referring to LMS running on your pCP ... which it probably is
> not doing ... assuming you want to keep using the LMS on your other
> server.
>
> If this is to be a player-only pCP then click on the player tab at the
> bottom of the sc
Alpine 3.14 just came out on 6/15 and I hadn't upgraded my server yet,
which I did this morning - lms seems to still be working after a reboot
so that's good!
Current package versions for x86_64 are:
lms-openrc-8-r0 x86_64 {lms} (GPL-2.0) [installed]
lms-8-r0 x86_64 {lms} (GPL-2.0) [installed]
paul- wrote:
> Open a ssh session, and do this
>
> 8< 8< 8< 8< 8< 8< 8<
>
Thanks for this!! Let there be light.
nincompoop's Profile: http://forums.slimdevices.com/member.php?userid=69805
View this threa
Paul Webster wrote:
> Did you try
> vers=3
> in options (instead of the vers=4.1 that you have in the screenshot)?
I've tried vers=3, vers=4, vers=4.1 and leaving it blank. Nothing
works.
Martin
DS918+, piCorePlayer, iPeng
Starting LMS is not needed.
That is referring to LMS running on your pCP ... which it probably is
not doing ... assuming you want to keep using the LMS on your other
server.
If this is to be a player-only pCP then click on the player tab at the
bottom of the screen then the confusing LMS info wi
Paul Webster wrote:
> In theory it (Squeezelite) could use the LMS in the sky that is
> mysqueezebox.com - however, ISTR that it does not because
> mysqueezebox.com wants to see real Squeezebox hardware players.
> So ... yes ... you should start an LMS locally and the one on your
> Openmediavaul
Ok so I mounted the boot partition, added forcefsck to the end of the
line below, restarted but I can't see any evidence in dmesg.
tc@PCP-XLR-LMS:/temp-boot$ cat cmdline.txt
host=PCP-XLR-LMS tz=GMT0BST,M3.5.0/1,M10.5.0 dwc_otg.fiq_fsm_mask=0xF
dwc_otg.lpm_enable=0 console=tty1 root=/dev/ram0 ele
In theory it (Squeezelite) could use the LMS in the sky that is
mysqueezebox.com - however, ISTR that it does not because
mysqueezebox.com wants to see real Squeezebox hardware players.
So ... yes ... you should start an LMS locally and the one on your
Openmediavault should be fine for that.
P
Greetings to all,
I installed LMS on my Openmediavault server and it works fine.
I installed Squeezelite on a Pi4 running Raspbian Pi4 to stream from my
LMS.
It works, but I found pCP setting more practical than the Squeezelite by
SSH!
My question is: if I want to run pCP as a player only, do I s
I tried a rPi 3b and was able to get that to work, sort of. My laptop
could see the test network but not connect. WiFi Analyzer showed the
SSID but the signal level seemed to drop after a few minutes. Had
another go with the rPi 4b, still no luck.
Googled Raspberry Pi wifi Access Point and found
I suspect you do it by adding it to cmdline.txt in the boot partition
since it is not explicitly listed in "Extras/Bootcodes"
Paul Webster
http://dabdig.blogspot.com
author of \"now playing\" plugins covering radio france (fip etc),
planetradio (bauer - kiss, absolute, scala, jazzfm etc), kcrw
Ok so how does one do that? The "User Commands" seem to run after LMS so
I'm guessing that's no good.
It'd be handy to have something like this run periodically to get some
advance warning of potential issues.
mr-b's Prof
In the pCP web interface look under Tweaks/Audio tweaks - you can
disable autostart in there.
Paul Webster
http://dabdig.blogspot.com
author of \"now playing\" plugins covering radio france (fip etc),
planetradio (bauer - kiss, absolute, scala, jazzfm etc), kcrw, supla
finland, abc australia,
17 matches
Mail list logo
