> > ADSLProvider in /var/lib/naat/configuration is cuted of after the 24
> > char... BTW... i don't configure the ADSL-Section in the webiface new to
> > see if it happens again... inet is working... i only notice this having a
> > look at the configuration-file
>
> what variable are you talking about ?
>
> ADSLProviders=
> ADSLProviderDomain=
> ADSLProviderDNS1=
> ADSLProviderDNS2=
upps...sorry... it was ADSLLogin (which is included in ADSLProviders)....
and i think that is no matter of the char-length...
i have to put a suffix behind my user:
'[EMAIL PROTECTED]'....
seems it cuts of all with/behind '#'....
in mnf8.2 this wasn't, i think... correct me if i wrong...
this is not realy bad, dsl-configuration is done once and works...
it's only nice2have for backups...
>
> and what did you change exactly, by hand, in your file ?
>
nothing...not that i remember :)
> > i have to modprobe ip_conntrack_ftp and ip_nat_ftp manual to get ftp
> > working.... a look into /usr/share/naat/templates/etc/shorewall/modules
> > shows this modules (tftp & irc not loaded 2, not to bad... they arent
> > needed at this time)... is this intended? or is there a screw2turn?
> >
> > javascript-checking in the host-section (ip-adress) is blocking my input
> > (192.168.10.0/24)... BTW at my first setup (with older shorewall
> > packages) after configure the hosts... shorewall breaks... it only runs
> > by if the hosts section was empty... now, after n update with the new
> > shorewall packages (florin's community) i get in trouble with the
> > jscript...
>
> Well, this is network address, not an IP/Netmask one so I should improve
> the javascript test or remove the test from those tags where both ips and
> network addresses are allowed. But, one question though, you can continue
> even if you get this invalid IP address error, can you ?
your right... i can.. gived up to soon....
but the shorewall dont runs by, after configure the hosts...
----------------------------------
[EMAIL PROTECTED] admin]# service shorewall check
Loading /usr/share/shorewall/functions...
Processing /etc/shorewall/params ...
Processing /etc/shorewall/shorewall.conf...
Loading Modules...
Notice: The 'check' command is unsupported and problem
reports complaining about errors that it didn't catch
will not be accepted
Shorewall has detected the following iptables/netfilter capabilities:
NAT: Available
Packet Mangling: Available
Multi-port Match: Available
Connection Tracking Match: Available
Verifying Configuration...
Determining Zones...
Zones: lan wan
Validating interfaces file...
Validating hosts file...
Determining Hosts in Zones...
Error: Invalid zone definition for zone lan
/sbin/service: line 148: 14483 Terminated $debug $servicedir/
$service $options
----------------------------------
here are my files:
----------------------------------
[EMAIL PROTECTED] admin]# cat /etc/shorewall/zones
#
~ snip ~
# Shorewall /etc/shorewall/zones
#zone display comments
lan LAN local_area_network
wan NET internet
#LAST LINE - ADD YOUR ENTRIES ABOVE THIS ONE - DO NOT REMOVE
[EMAIL PROTECTED] admin]# cat /etc/shorewall/hosts
#
~ snip ~
# Shorewall /etc/shorewall/hosts
#zone host options
lan eth1:192.168.10.0/24
wan ppp+:0.0.0.0/0
#LAST LINE - ADD YOUR ENTRIES ABOVE THIS ONE - DO NOT REMOVE
----------------------------------
after deleting all the hosts i can run service shorewall start:
----------------------------------
~ snip ~
Determining Zones...
Zones: lan wan
Validating interfaces file...
Validating hosts file...
Determining Hosts in Zones...
LAN Zone: eth1:0.0.0.0/0
NET Zone: ppp+:0.0.0.0/0
Validating policy file...
~ snip ~
----------------------------------
BTW routestop function takes not care of any hosts.. if i fire shorewall stop
(connected from Lan/SSH) im not realy disconnected from the box....
>
> > are here any knowlege about madwifi?
> > with the 2.6.3 kernel i cant compile the driver...
> > now with the 2.6.7 compiling (actual cvs-snapshot) seems to run by,
> > but with insmod the wlan.ko i get an "invalid module format" error...
> > perhaps someone has ready2use packages?
> > its not easy to find anything about madwifi playing with mandrake...
>
> I'm talking right now with the kernel maintainer and he says that, indeed,
> the mad wifi driver doesn't work too well ... and that is not only a
> mandrake issue :o) I didn't look at that so I take his word for it ..
>
hmm... ok... i have a atheros card for windows to sell :-))
> > now, at last... florin, are there devel packages for the new naat... im
> > playing with a thought of porting the webiface language to german and
> > give my little part to a great product (if there is a need of!??)...
> > perhabs some other guys playing with the same thought, and share with
> > me??
>
> well, MNF is maintained using CVS. It's quite easy to work with :o)
> there is is this firewall2 module which contains, mainly, some
> directories:
> frontend (the web interface code), backend (the backend engine), mnf (the
> mnf-en cirtual rpm package), monitoring (the naat-monitoring package), and
> httpd-naat (the httpd-naat and httpd2-naat packages).
>
> Now, one can simply compile the packages using the 'make rpm' command.
> Concerning the translations in general: most of MNF is already translated
> into German, French, Portuguese, Italian and Spanish if I'm not mistaking.
>
> For practical reasons, I have commented out the differents sections in the
> Makefile so I won't build all the languages packages every day. I have
> noticed after some time that the translations compile is broken. It is
> based on xml files, as the whole frontend description of the pages.
>
> I will have to come back and fix that during the next week or two but if
> you can have a look and fix that, it would be great.
>
> You can also contributed to the translations (see how they are done in the
> cvs) and eventually contact [EMAIL PROTECTED] (translation
> coordinator) or/and [EMAIL PROTECTED] (documentation coordinator)
> or simply translate the pages and let me know ... I'll commit that and fix
> the translations compile if don't do it.
>
> I hope I was clear enough,
yes,ok... thx... perhaps i will check out from cvs and look at it...
greatz FrankB
____________________________________________________
Want to buy your Pack or Services from MandrakeSoft?
Go to http://www.mandrakestore.com
Join the Club : http://www.mandrakeclub.com
____________________________________________________
