sai <[EMAIL PROTECTED]> writes: > Hello Florin, > > We installed the 1-10 iso and install went OK (though problems > with one LAN card which I need to investigate - might be a bad > card). > > I am unable to get the web interface on the LAN, although if I lynx > https://127.0.0.1 on the console I get the web interface OK. When > I install MNF8.2 on the same machine it all goes fine and I can > access the MNF web-interface OK. > > sai
Hi, make sure the httpd2-naat service is up and also that you have the right network IP addresses (if you're not using 127.0.0.1). Also, make sure that shorewall is not in the way :o) (use shorewall clear and try again) ... my 2cts, > Wednesday, July 14, 2004, 3:02:38 AM, you wrote: > > F> Jason Allen <[EMAIL PROTECTED]> writes: > > >> My install also went flawlessly, nice work Florin! I've only been playing > >> with it a short while, but it looks very clean, and very robust. It may > >> be the solution we've been looking for, just need to test the VPN tunnel's > >> w/ our Sonciwalls. I believe the sonicwalls use the x509 authentication > >> as well but I'm not positive, still need to venture over to have a look. > >> Quick question, any ideas (ballpark figures would be fine) on pricing of > >> the new MNF, and release date? Jason > > F> Sonicwall uses several types of VPNs depending on the product ... but I > F> would reccomend you use VPNs with x509 certificates > > F> The new version of MNF was first meant to come out on july ... but in > F> order to finish the translations and make more tests ... it will probably > F> come out on september ... > > F> Sincerely, > > >> > >> Justin Grote wrote: > >> > >> >Heyo, > >> > > >> >Since this might as well become the installation success/fail thread, I fired it > >> >up in a VMWare enviroment and it installed flawlessly. I assume it was basically > >> >a Mandrake 10 install with an > >> answer file, lending to the pre-pre-pre alpha theme :) > >> > > >> >Haven't had a chance to beat on it yet, but when I do, I'd like to know a couple > >> >things so I can make your life easier Florin: > >> > > >> >1. Should I post problems here, or on the new Bugzilla for MNF? > >> >2. Should I work solely off the ISO images, or should I be checking the CVS and > >> >working off the most recent update? > >> > > >> >Thanks! :) > >> > > >> >______________________________ > >> >Justin Grote > >> >Network Architect, CCNA > >> >JWG Networks > >> >Email: [EMAIL PROTECTED] (remove nospam-) > >> >SMS: [EMAIL PROTECTED] (remove nospam-) > >> >Phone: (208) 631-5440 > >> > > >> >------------------------------ > >> >Original Message Follows > >> >------------------------------ > >> >F> "Donato Marino Jr." <[EMAIL PROTECTED]> writes: > >> > > >> > > >> >>>Dear Florin > >> >>> > >> >>>I�ve just donwloaded the "pre-pre-pre alpha ISO image", burned > >> >>>a cd and start the installation. In the summary step apears the > >> >>>message > >> >>> > >> >>>" an error occured > >> >>> foomatic-db-engine rpm not found " > >> >>> > >> > > >> >F> Hi, > >> > > >> >F> have you tried to configure your printer ? :o) > >> > > >> >>>Nothing more can be done from this moment.... > >> >>> > >> >>> Any idea about this problem? Thanks a lot > >> >>> > >> >>>Donato Marino Jr. > >> >>>[EMAIL PROTECTED] > >> >>> > >> > > >> > > > > ____________________________________________________ > Want to buy your Pack or Services from MandrakeSoft? > Go to http://www.mandrakestore.com > Join the Club : http://www.mandrakeclub.com > ____________________________________________________ -- Florin http://www.mandrakesoft.com http://people.mandrakesoft.com/~florin/
____________________________________________________ Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com Join the Club : http://www.mandrakeclub.com ____________________________________________________
