a firewall with an internal interface setup to use dhcp ... it doesn't
make sense ... :o)
>Doug White <[EMAIL PROTECTED]> writes:
> Yes, it has dhcpd set as the client. There doesn't seem to be a way to
> not have a client selected. It should be a static interface and is set up
> that way and works,
>
> Thanks
>
> Florin wrote:
>
> >Hi,
> >
> >Is the interface associated to this dhcp section already setup with a dhcp
> >client ?
> >
> >
> >>Doug White <[EMAIL PROTECTED]> writes:
> >>
> >
> >
> >>It does write to the file but this is what it puts in dhcpd.conf
> >>
> >>ddns-update-style none;
> >>subnet 0.0.0.0 netmask 255.255.224.0^M {
> >> # default gateway
> >> option routers 172.16.64.1^M;
> >> option subnet-mask 255.255.224.0^M;
> >> option broadcast-address 255.255.255.255;
> >>
> >> #domains
> >> option domain-name "rwu.edu";
> >> option domain-name-servers 66.181.224.13;
> >>
> >> #dynamic range
> >> range 0.0.0.200 0.0.0.225;
> >> default-lease-time 21600;
> >> max-lease-time 43200;
> >>
> >>when I entered 172.16.64.0/19 as the network, eth2 as the interface
> >>(associated with 64 subnet) and 200-225 as the range of addresses. If the
> >>0's are wildcards I suppose it is correct, but it doesn't issue any
> >>addresses on that network. Is it possible the DHCP server listens on some
> >>other port (than 67)?
> >>
> >>Florin wrote:
> >>
> >>
> >>>Doug White <[EMAIL PROTECTED]> writes:
> >>>
> >>>
> >>>
> >>>>I am trying to set up DHCP with MNF on two of the interfaces eth2 and
> >>>>eth3. When I look at the dhcpd.conf file, it seems really odd and dhcp
> >>>>doesn't work. I presume it runs on udp port 67 but how do you put in the
> >>>>ips you want to use and specify the subnets. They always seem to be
> >>>>0.0.0.0/0 in the file after it is setup. I want to set it up on two
> >>>>networks 172.16.64.0/19 and 172.16.96.0/19 on the two interfaces for ips
> >>>>172.16.64.200-225 and 172.16.96.226-249 respectively. Any advice is
> >>>>appreciated.
> >>>>
> >>>>
> >>>in the dhcp section you can choose the network interface: for example
> >>>eth3. Then, you choose the dynamic IP range: for example 200-225. This
> >>>will read the eth3 IP address/network: for example 172.16.64.0/19 and
> >>>create the dhcpd.conf entries for that: the whole subnet section
> >>>corresponding to that network (interface).
> >>>
> >>>please let me know if this does not work for you ...
> >>>
> >>>good luck,
> >>>--
> >>>Florin http://www.mandrakesoft.com
> >>> http://people.mandrakesoft.com/~florin/
> >>>
> >>> ------------------------------------------------------------------------
> >>>
> >>>____________________________________________________
> >>>Want to buy your Pack or Services from MandrakeSoft? Go to
> >>>http://www.mandrakestore.com
> >>>Join the Club : http://www.mandrakeclub.com
> >>>____________________________________________________
> >>>
> >>>
> >>____________________________________________________
> >> Want to buy your Pack or Services from MandrakeSoft? Go to
> >> http://www.mandrakestore.com
> >>Join the Club : http://www.mandrakeclub.com
> >>____________________________________________________
> >>
> >
> > ------------------------------------------------------------------------
> >
> >____________________________________________________
> > Want to buy your Pack or Services from MandrakeSoft? Go to
> > http://www.mandrakestore.com
> >Join the Club : http://www.mandrakeclub.com
> >____________________________________________________
> >
>
> ____________________________________________________
> Want to buy your Pack or Services from MandrakeSoft?
> Go to http://www.mandrakestore.com
> Join the Club : http://www.mandrakeclub.com
> ____________________________________________________
--
Florin http://www.mandrakesoft.com
http://people.mandrakesoft.com/~florin/
____________________________________________________
Want to buy your Pack or Services from MandrakeSoft?
Go to http://www.mandrakestore.com
Join the Club : http://www.mandrakeclub.com
____________________________________________________
