I got this already in my LIB/Makefile. Best regards Gregor On Tue, 2010-10-26 at 14:38 +0200, Lars Ottemoller wrote: > In the LIB/Makefile you need to have > > $(OUTPATH)/seed.$(osuf): seed.for $(INCS) > $(fc) -fno-range-check seed.for > > does that not work? > > Lars > > > On 26/10/10 13:28, Gregor Schweppe wrote: > > Hello again, > > without 'ONLY_gfortran64 = $(OUTPATH)/bgisei' in PRO/Makefile I get this > > new error message: > > > > 'Error: Arithmetic overflow converting INTEGER(8) to INTEGER(4) at (1). > > This check can be disabled with the option -fno-range-check > > make[1]: *** [seed.o] Error 1 > > make[1]: Leaving directory `/home/gschwepp/Seismo/seisan/LIB' > > -------------------------------------------------- > > ---- COMPILING SEISAN 8 PROGRAMS ----------------- > > -------------------------------------------------- > > make: *** No rule to make target `../LIB/./seisan.a', needed by `ahsei'. > > Stop.' > > > > The error occurs even if I add -fno-range-check again. > > > > Best regards, > > Gregor > > > > On Tue, 2010-10-26 at 12:54 +0200, Lars Ottemoller wrote: > >> Hi Gregor, > >> > >> can you please try to remove bgisei from the ONLY_gfortran64 in the PRO > >> Makefile, and see if you can compile the rest with gfortran? > >> > >> My Ubuntu is not that uptodate, and I have not yet seen this problem. > >> > >> Regards, > >> Lars > >> > >> > >> On 26/10/10 11:49, Gregor Schweppe wrote: > >>> Hello, > >>> > >>> I tried to compile seisan with gfortran 4.4.5 on Ubuntu 10.10 Maverik. I > >>> set SEISARCH to 'gfortran64', goto PRO and start compilation with 'make > >>> all'. After a few lines I get the following error: > >>> > >>> 'Error: Arithmetic overflow converting INTEGER(8) to INTEGER(4) at > >>> (1). This check can be disabled with the option -fno-range-check > >>> make[1]: *** [seed.o] Error 1 > >>> make[1]: Leaving directory `/home/gschwepp/Seismo/seisan/LIB' > >>> -------------------------------------------------- > >>> ---- COMPILING SEISAN 8 PROGRAMS ----------------- > >>> -------------------------------------------------- > >>> make: *** No rule to make target `../LIB/./seisan.a', needed by > >>> `bgisei'. Stop.' > >>> > >>> To check if the error is in my system I set SEISARCH to 'linux'. Typed > >>> 'make clean' in /PRO and /LIB and started compilation with g77. I got no > >>> error message, everything works fine. > >>> > >>> I changed '$(fc) bgisei.for' to '$(fc) -fno-range-check bgisei.for' in > >>> PRO/Makefile and tried to recompile it with gfortran. It did not work > >>> either (same error). > >>> > >>> I don't know how to fix it. But maybe someone else does. > >>> > >>> Best regards, > >>> > >>> Gregor > >>> > >>> > >>> > >>> > >>> _______________________________________________ > >>> seisan mailing list > >>> [email protected] > >>> http://mailman.uib.no/listinfo/seisan > >> > > > > > > > > _______________________________________________ > > seisan mailing list > > [email protected] > > http://mailman.uib.no/listinfo/seisan >
_______________________________________________ seisan mailing list [email protected] http://mailman.uib.no/listinfo/seisan
