Hi Abhash,
 
you did add the SEISAN.csh to your .cshrc, right? I think there is a problem 
actually :-)
You wrote: "I have also added the line "source/home/seismo/COM/SEISAN.csh" in 
.cshrc file for activation."
 
It seems there is no "space" after the 'source' command. It should read 'source 
/home/seismo/COM/SEISAN.csh', that is, if the location is correct. Otherwise 
please change the location to the right file.
 
In the SEISAN.csh there is the definition for SEISAN_TOP. In your .cshrc there 
might be a PATH entry like 'setenv PATH=/some/path:$PATH'. Change this entry to 
'setenv PATH=/some/path:/Volume/disk_1/seismo/PRO:$PATH'.
 
After doing those changes please log out and log in again and try the 'wo' and 
'dirf' stuff from the instructions again.
 
Best wishes,
Max
 



________________________________

        Von: Abhash Kumar [mailto:[email protected]] 
        Gesendet: Donnerstag, 29. März 2012 08:22
        An: Krickl, Maximilian
        Betreff: Re: [seisan] Installation
        
        
        Hi Max,
                Thanks for your concerned reply. In case if I will not get the 
correct stuff then where should I edit ( I mean which directory? Is it COM or I 
need to put this in .cshrc file)


        Thanks
        Abhash
        Sent from my iPhone

        On Mar 29, 2012, at 2:03 AM, <[email protected]> wrote:
        
        

                Hi Abhash,
                 
                you can type this anywhere. In $PATH should be some folder like 
"/Volume/disk_1/seismo/PRO" and $SEISAN_TOP sould be "/Volume/disk_1/seismo" in 
your case.
                 
                Best wishes,
                Max
                 
                --------------------------------

                Maximilian Krickl
                Dipl.-Ing. (FH), Regierungsbeschäftigter
                Fachbereich
                Landeserdbebendienst, Beratung Untergrundgefahren
                
                Geologischer Dienst NRW - Landesbetrieb -
                De-Greiff-Str. 195
                D- 47803 Krefeld
                
                Tel.:   +49 (0) 21 51 / 897 - 502
                Fax:   +49 (0) 21 51 / 987 - 505
                eMail: <mailto:[email protected]> 
[email protected]
                Internet:         http://www.gd.nrw.de <http://www.gd.nrw.de/> 


________________________________

                        Von: Abhash Kumar [mailto:[email protected]] 
                        Gesendet: Donnerstag, 29. März 2012 08:01
                        An: Krickl, Maximilian
                        Betreff: Re: [seisan] Installation
                        
                        
                        Hi Max,
                                 I should type -'echo $PATH' and 

                                - 'echo $SEISAN_TOP' in the seismo directory or 
can I do this from any other directory. I have my seismo directory in 
/Volume/disk_1 directory, so 'echo $SEISAN_TOP should return me 
/Volume/disk_1/seismo? I will be grateful for your advice.

                        
                        
                        Thanks
                        Abhash
                        

                        On Mar 29, 2012, at 1:41 AM, < 
<mailto:[email protected]> [email protected]> wrote:
                        
                        

                                Hi Abhash,
                                 
                                please check if you set the environment 
variable PATH and SEISAN_TOP correctly.
                                - 'echo $PATH'
                                - 'echo $SEISAN_TOP' 


________________________________

                                        Von: abhash kumar 
[mailto:[email protected]] 
                                        Gesendet: Donnerstag, 29. März 2012 
00:22
                                        An: <mailto:[email protected]> 
<mailto:[email protected]> [email protected]
                                        Cc: Krickl, Maximilian; Gregor Schweppe
                                        Betreff: Installation
                                        
                                        
                                        Hi,
                                           I was going through the seisan 
training manual and it says that if I want to check whether seisan is 
successfully installed or not then I should give a command "wo" to move to the 
WOR directory and if that works then try command dirf, if no protests, the 
software is successfully installed. I tried wo and it directed me to the WOR 
directory but when I used dirf it says command not found as shown below:
                                        
                                        /Volumes/disk_1/seismo > wo
                                        /Volumes/disk_1/seismo/WOR > dirf
                                        dirf: Command not found.
                                        
                                        I am perplexed as to how to check 
whether seisan is correctly installed or not. Please suggest me something.
                                        
                                        Thanks
                                        Abhash
                                        

                                _______________________________________________
                                seisan mailing list
                                <mailto:[email protected]> [email protected]
                                <http://mailman.uib.no/listinfo/seisan> 
http://mailman.uib.no/listinfo/seisan
                                

                _______________________________________________
                seisan mailing list
                [email protected]
                http://mailman.uib.no/listinfo/seisan
                

_______________________________________________
seisan mailing list
[email protected]
http://mailman.uib.no/listinfo/seisan

Reply via email to