Hello again, I forgot to ask one thing: When we use Continuous Extract in CORR, it seems that in the extracted waveforms I always get a time window equal to that of the master signal duration + 10 seconds. How can I extend this time window? I don't mind changing the source code, but can't find where is this hardcoded in the source code.
Thank you once more. Best regards, Emanuel A. 2015-03-20 19:11 GMT+00:00 Emanuel Antunes <[email protected]>: > Greetings to all, > > > Thank you Peter for your input. So, it should be 2.400.000 for the > maximum number of points in one trace. > How does this depend on the sample rate? I thought the space taken in > memory depended only on the number of points. Having a trace with 1000 > samples at 50 sps takes as much space as one with 1000 samples at 25 > sps, the difference should be that the first is half the time length > of the second, am I right? > > By the way, I managed to cut the MiniSEED files with WAVETOOL using > the -cseed option. 12h files at 50sps got 2160000 samples which is > under the maxpoints limit. Thank you for the MSCUT idea but being > limited to 1h or 15min files might generate too many files. > Fortunately CORR can manage 12h files at that sps. > > I have two further questions tough: > > - What format should the event list ("SFILE INDEXFILE" parameter) > have? Should it look like the DIRF produced files? Can we address > other folders in this SFILE parameters? (I am asking this because > after much trials I can only input s-files which are on the same > folder from where I am running CORR, and can't use the s-files > lists...). > > - It looks like for each phase in the S-File, and each event S-File, > CORR only picks the maximum, and not all the local maxima above the > minimum correlation threshold, am I right? > I am asking this because my aim is not to improve picks, nor do a > correlation matrix of events, but rather, to detect new events with > similar waveforms in a continuous waveform... > > Have a great weekend, > Regards, > > Emanuel Antunes > > 2015-03-20 7:10 GMT+00:00 Voss, Peter <[email protected]>: >> Hello Emanuel, >> >> Maximum samples: it depends on your sample rate, see limits in chapter 3.1. >> On unix you can use MSCUT to split your miniseed waveform files, see mscut -h >> >> Good luck, >> Peter >> >> -----Oprindelig meddelelse----- >> Fra: [email protected] [mailto:[email protected]] På vegne >> af Emanuel Antunes >> Sendt: 19. marts 2015 13:46 >> Til: [email protected] >> Emne: [seisan] CORR and Segmentation Faults >> >> Dear SEISAN community, >> >> >> I have been trying to run the CORR routine to identify unknown/uncatalogued >> events with similar waveforms in a continuous database, where the master >> event waveforms are already sliced, so only the scanned continuous waveforms >> are whole. >> My problem, so far, is that I am constantly getting segmentation faults, >> even when MULPLT is able to deal with the waveforms (I got segmentation >> faults while using SEISAN 9.1 MULPLT on the same waveforms, by the way). >> Could this be a limitation of the CORR routine? What can the maximum length >> (in samples) be? Is the data format much relevant in this case? >> I must say I sliced one of the continuous waveforms in a 6 hours segment and >> I was able to run the program. So I suppose I could do the same for all the >> months of data I have, but before doing that, I would prefer to have some >> expert opinion on what is the maximum length allowed. However, I couldn't >> split the file using WAVETOOL (Segmentation Fault) ou rdseed_many, nor >> SEISEI, I had to resort to ObsPy to slice/split the waveform. Is there a way >> to do it in SEISAN? >> There must be, if MULPLT can read the long SEED files, there must be a way >> for other programs to read them... >> >> I am currently using SEISAN 10.3, and my waveforms are in miniseed. >> All advice is very welcome. >> Thank you all in advance, >> >> Best regards, >> >> >> PS : Dear developers, there is a typo in the version tag : " SEISAN >> 10.3 , Janauary 2015 " >> >> -- >> Emanuel Antunes >> >> Seismology Laboratory >> Instituto Superior Técnico (IST) >> Universidade de Lisboa (UL) >> >> _______________________________________________ >> seisan mailing list >> [email protected] >> http://mailman.uib.no/listinfo/seisan > > > > -- > Emanuel Antunes > > MSc in Physics Engineering > Seismology Laboratory > Instituto Superior Técnico (IST) > Universidade de Lisboa (UL) -- Emanuel Antunes MSc in Physics Engineering Seismology Laboratory Instituto Superior Técnico (IST) Universidade de Lisboa (UL) _______________________________________________ seisan mailing list [email protected] http://mailman.uib.no/listinfo/seisan
