----- Original Message -----
From: teri...@aol.com
To: silver-list@eskimo.com
Sent: Saturday, November 17, 2001 9:36 PM
Subject: Re: CS>using cs with airbrush
l have just received my airbrush from harbor freight in the mail but now l
need instructions on how to use it with cs..can anyone tell me that? thankyou,
teri.
From: Brooks Bradley
To:
Sent: Sunday, 25 April 1999 10:12
Subject: CS>Parts List and Comments on CSXO2 Nebulizing System
Good Afternoon List Members.
Following is a list of the components required for enabling
the protocol we used in the experimental researches I outlined last
evening.
The air-brush kit we used, was obtained from a mail-order
concern specializing in myriad hardware/electrical/hand-tool items.
Their quality is toward the low-end industrial, but quite adequate for
the home/hobby user. Our machine shop/proto-type builders have used
them for years. The company is Harbor Freight, located in Camarillo,
California. They now have outlets in one or two other cities. We
obtained our air-brush kits from the Fort Worth, Texas store (we are
located in Fort Worth). The stock number is #6131. Our purchasing
person informed me this item cost us less than $10.00 each, and the
last 20 purchased cost less than $8.00. As of last Wednesday, this
store still had some of these units. Included in the kit are two
liquid -supply bottles (one 1/2 and one 1 oz), one air hose which
couples between the pressure regulator and the air-brush assembly;
one air pressure regulator; and the air-brush assembly itself. The
additional parts required are for a hose assembly which facilitates
coupling the input side of the air pressure regulator with the
external oxygen supply used to power the nebulizer.
Note: PURCHASE BRASS FITTINGS ONLY, oxygen is the
pre-eminent combustion supporter.
All of these components can be obtained from any
commercial outlet stocking pneumatic system parts.
This hose assembly includes:
One 1/4" Compression X 1/8" Male NPT fitting (this
is very important, for without it you cannot connect the O2 hose to
the air-brush pressure regulator)
One 1/4" Barb X 1/8" NPTF Fitting
One 1/4" X 9/16 RH Oxygen Fitting (will have a barb
fitting on one end and the female coupling on the other)
Approximately 4 feet of any good !/4 I.D. 200+
PSI air hose. Tell the clerk you are going to use oxygen in the
hose.
Assemble the parts by screwing the Compression
fitting into the 1/4" Barb X 1/8" Male NPT fitting. Do not worry,
only one end of the Compression fitting is compatible with the Barb
fitting. Next, insert the barb end of this fitting assemby into the
air hose. Push the hose on until it is jam against the shoulder of
the fitting. Any small, screw or compression-type clamp may be used
to add security to the hose/fitting end. Next, insert the barb end of
the Oxygen fitting into the remaining hose end and secure with any
satisfactory clamp. Your assembly is now complete. Next, carefully
screw the exposed male end of the Compression fitting into the bottom
of the air-brush pressure regulator. Now connect the small-diameter
air-line between the air-brush assembly and the pressure regulator (it
is fool-proof, as there is nowhere else this tiny hose can connect).
Select the small fluid-supply bottle and fill
approximately 75-80% of capacity with 5-10 ppm Colloidal Silver and
insert the angled tip assembly into the bottom of the air-brush
assembly. You are now ready to connect to your O2 supply and operate.
Obtain a small medical O2 bottle (anywhere around 1/2
to 1 cubic feet capacity) or any size O2 Arc welding system bottle.
Be sure to have a Two-stage regulator attached to the O2 bottle. Now,
connect the 9/16" Oxygen-fitting to the O2 outlet from the Two-stage
regulator (also foo-proof, as there is nowhere else to connect). Now
SLOWLY open the O2 control knob on the O2 regulator and set the inlet
prssure to your nebulizer assembly to a Maximum of 35 Pounds Per
Square Inch (PSI). Next, screw the AIR-BRUSH air pressure
regulator control knob (the tiny knob on top of the air pressure
regulator) all the way closed.. Now, open the control knob about 2
and one-half turns. Next, trigger the control botton on the
Air-brush head until you see a fine fog each time you press down on
the
button. The mist is so fine, you may have to hold it against a dark
back ground to see it. You are now ready to go.
Our best results were obtained by the volunteer inserting
the discharge nozzle about 1 inch inside their OPEN mouth and
breathing deep---an long---on each inhalation; holding the breath for
a count of 3 or 4 and then executing a complete exhalation. Ideally,
there should be about 1/4" circular clearance around the air-brush
head (while inside the mouth), as this provides the optimum venturi
action for incorporating air with the O2. In acute circumstances, the
volunteer can close his/her mouth completely around the nozzle and
breathe 100% O2------works great.
Remember NEVER USE PURE OXYGEN NEAR OPEN FLAMES OR
COMBUSTIBLE MATERIALS. To do so would make this protocol quite
irrelevant.
Good luck to all, and if you have any questions just post
them and I will try to answer. Sincerely. Brooks Bradley. p.s.
Any serviceable air-brush assembly could be used. However, try to
obtain one that will yield the smallest size particle possible.
