Wayne said,
“Terry, you appear to be a near genius at brewing CS,
However if you have a system that will not change the
current as you add loads in parallel, you have bested
Einstein. <grin> Sounds like you have a hefty power
supply that has some unknown percent regulation.”

My power supply is the 110 VAC from the wall, run
through a rectifier to make it DC. (A near-genius,
huh? Cool!)

“If you add a load in parallel, the basic rules that
apply to circuits will add the current as needed to
each load, if your voltage source can provide it
without being overloaded which will manifest itself by
a change in voltage. If the voltage changes, then the
current will change to all loads equally. The "Voltage
NO Load" ratio to the "Voltage Full Load" is referred
to as "percent regulation". Some of the genuine
engineers on the list can explain this better. It has
been years since I studied all that. Plus, I am only a
redneck that has never been to school. Some of us
worry too much about details, while others worry too
little. I have some load resistors that would load
your supply to allow you to see how many jugs you
could run. These are very large resistors mounted on
1/4 inch alum plate. I built this loading array to
draw 100 amps at 12 VDC for some power supplies we
were building a few years ago. At 100 VDC, it would
draw only about 12 amps. OF course some heating
results that changes the resistance slightly. My
thinking is, that if you force 2.5 ma through 5.0
inches, it would be near the same work dissipation as
if you forced 5.0 ma and the spacing was 2.5 inches.”

But then, Steve said,
“It's not that simple. If each jar was EXACTLY the
same as the others, then yes, the current would divide
equally. But they will not be exactly the same. One of
them will have a lower resistance than the others, and
will draw more current. Thus the ppm production for
that jar will be higher than the others, making the
resistance go down faster than the others, drawing
more current than the others, producing even more ppm
than the others, dropping the resistance even more
than the others, hogging even more of the current, and
so on. It wouldn't surprise me if you had at least a
20% variation in final strength amongst the jars. You
would produce more consistent CS product using one
large jar that hold the contents of 10 or 20 smaller
jars. Or put the jars in series and take much longer
to produce your product.”

My response,
There’s too much Technical-speak here for me. As much
as I can gather from what Steve said, he thinks the
ppm levels would differ from jar to jar. The reason
why I don’t believe that is true is because, if I
over-cook the batch (say, for an hour and a half,
instead of an hour), the CS in every jar turns yellow,
not just in one jar. When I stick to the formula (one
hour), none of the CS turns yellow. If Steve’s
reasoning was accurate, one or some of the jars would
produce yellow CS, since the current would be uneven
in one/some of the jars. There ARE minor differences
between one jar and another. Some of the wires are
more worn and are thinner in some jars than others.
Some of the wires are longer in some of the jars. None
of this makes any difference. I can produce crystal
clear CS in all ten jars every time, if I don’t
deviate from the formula.

The kind offer to send me resistors is unnecessary
because the current does not need to be limited. What
I’m doing is simply this: I hang silver wires into DW,
add some CS to speed up the process, and brew it until
the current reaches 25 mA. It is then done. I do have
a power source that measures the current and the
voltage at the same time, showing on two gauges the
whole time. This instrument is why I know the current
is 25 mA by the time the batch is done. I used it for
awhile, but the wall power is simpler and easier.

Terry Chamberlin
Metabolic Solutions Institute
RR1  314 Carleton Rd
Lawrencetown, NS B0S 1M0
902-584-3810 voice
413-826-7641 fax service
[email protected]


______________________________________________________________________ 
Find, Connect Date! http://personals.yahoo.ca


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]
Silver-list archive: http://escribe.com/health/thesilverlist/index.html
List maintainer: Mike Devour <[email protected]>