Seguinte pessoal Consegui coletar mais algumas informações. Alguém poderia me dar uma luz, para mostrar o por que não está inicializando?
Grato 2007-10-03T18:00:49+0000 Linux version 2.6.16-xenU ([EMAIL PROTECTED]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled Built 1 zonelists Kernel command line: root=/dev/sda1 ro 4 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Xen reported: 2004.544 MHz processor. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Software IO TLB disabled vmalloc area: ee000000-f53fe000, maxmem 2d7fe000 Memory: 1718700k/1748992k available (1958k kernel code, 20948k reserved, 620k data, 144k init, 1003528k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4010.63 BogoMIPS (lpj=20053152) Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) Checking 'hlt' instruction... OK. Brought up 1 CPUs migration_cost=0 Grant table initialized NET: Registered protocol family 16 Brought up 1 CPUs xen_mem: Initialising balloon driver. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered i8042.c: No controller found. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Xen virtual console successfully installed as tty1 Event-channel device installed. netfront: Initialising virtual ethernet driver. mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 Registering block device major 8 IP route cache hash table entries: 65536 (order: 6, 262144 bytes) TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Using IPI No-Shortcut mode md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 144k freed *************************************************************** *************************************************************** ** WARNING: Currently emulating unsupported memory accesses ** ** in /lib/tls glibc libraries. The emulation is ** ** slow. To ensure full performance you should ** ** install a 'xen-friendly' (nosegneg) version of ** ** the library, or disable tls support by executing ** ** the following as root: ** ** mv /lib/tls /lib/tls.disabled ** ** Offending process: init (pid=1) ** *************************************************************** *************************************************************** Continuing... INIT: version 2.86 booting INIT: cannot execute "/etc/rc.d/rc.S" INIT: Entering runlevel: 4 INIT: cannot execute "/etc/rc.d/rc.M" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: cannot execute "/etc/rc.d/rc.4" INIT: Id "x1" respawning too fast: disabled for 5 minutes INIT: no more processes left in this runlev On Oct 2, 5:49 pm, conradojr <[EMAIL PROTECTED]> wrote: > PessoALL > > Estou querendo criar uma imagem do slack12 para largar no EC2 (http:// > aws.amazon.com/). > Estou gerando ela assim: > > mkdir /mnt/ami > dd if=/dev/zero of=/mnt/slackware-12-base.fs bs=4M count=1024 > mkfs.ext3 -F -j /mnt/slackware-12-base.fs > mount /mnt/slackware-12-base.fs /mnt/ami -o loop > mkdir /mnt/ami/dev > MAKEDEV -d /mnt/ami/dev/ -x console > MAKEDEV -d /mnt/ami/dev/ -x null > MAKEDEV -d /mnt/ami/dev/ -x zero > mkdir /mnt/ami/etc > > aih crio um fstab com o seguinte conteúdo: > > /dev/sda1 / ext3 defaults 1 1 > none /dev/pts devpts gid=5,mode=620 > 0 0 > none /dev/shm tmpfs defaults 0 0 > none /proc proc defaults 0 0 > none /sys sysfs defaults 0 0 > /dev/sda2 /mnt ext3 defaults 0 0 > /dev/sda3 swap swap defaults 0 0 > > mkdir /mnt/ami/proc > > mount /mnt/slackware-12.0-install-dvd.iso /mnt/dvdrom -o loop > > e criei um script que faz o seguinte com os pacotes > > cp /mnt/dvdrom/slackware/a/jfsutils-1.1.11-i486-1.tgz /mnt/ami/. > tar -xzvf /mnt/ami/*.tgz > sh ./install/doinst.sh > > ou seja, descompacto todos os pacotes lá dentro do '/' da minha > imagem, e executo o doinst.sh em seguida. (faço isso para cada pacote > das seguintes séries) > a > ap > d > l > k > n > > copio o passwd, group e shadow para o etc, e seto as permissões. > copio o sshd_config /etc/ssh/ > > desmonto e sincronizo > > faço os pacotes, e envio para o S3. > > Porém não estou conseguindo acertar a imagem, pois não consigo > conectar. > > Alguém mexe com ec2 e pode me dar uma luz? > > Grato --~--~---------~--~----~------------~-------~--~----~ GUS-BR - Grupo de Usuários de Slackware Brasil http://www.slackwarebrasil.org/ http://groups.google.com/group/slack-users-br -~----------~----~----~----~------~----~------~--~---
