Try turning up the log verbosity:
$ slon -d 4 rep_atr_prod "dbname=atr_test user=postgres"
And post the output. I assume the _rep_atr_prod schema exists on this
db?
-Casey
On Oct 16, 2006, at 12:40 PM, Luke Morehead wrote:
> I've pasted an initial E-mail conversation below. The actual slon
> launch command and output is as follows:
>
> [EMAIL PROTECTED]:/$ slon rep_atr_prod "dbname=atr_test user=postgres"
> 2006-10-12 08:49:16 EDT CONFIG main: slon version 1.1.0 starting up
> 2006-10-12 08:49:16 EDT FATAL main: Node is not initialized properly
> 2006-10-12 08:49:16 EDT DEBUG2 slon: exit(-1)
>
> Is it possible to get any more specific info about where and how the
> node is not initialized? Could there be a problem with the
> _rep_atr_prod schema even though slon is running fine on the master
> host
> and database? If so is there a script that can actually remove all
> the
> slony info (rowID columns, triggers, operators, etc.) from the master
> database so I can start over from scratch, or is that a manual
> process?
>
> Thanks very much,
> Luke
>
> -----Original Message-----
> From: Christopher Browne
> Sent: Wednesday, October 11, 2006 1:48 PM
> To: Luke Morehead
> Subject: Re: Slony help
>
> On 10/10/06, Luke Morehead wrote:
>> Chris,
>>
>> I ran the slony1_extract_schema.sh script (using a test database) and
> used the output to populate a fresh slave database. I then ran
> slonik_init_cluster. After this slon_start ran fine for the master
> node
> but failed for the slave node with the error, "FATAL main: Node is
> not
> initialized properly".
>>
>> The buzz online seems to indicate a problem with the (clustername)
> schema. However the schema looks fine in the slave database. What
> could this be?
>
> That message comes from the following code...
> /*
> * Get our local node ID
> */
> rtcfg_nodeid = db_getLocalNodeId(startup_conn);
> if (rtcfg_nodeid < 0)
> {
> slon_log(SLON_FATAL, "main: Node is not initialized
> properly\n");
> slon_exit(-1);
> }
>
> If there isn't a rtcfg_nodeid value, then that means the call to
> db_getLocalNodeId() failed.
>
> /*
> * Select the last_value from the sl_local_node_id sequence
> */
> snprintf(query, 1024, "select last_value::int4 from
> %s.sl_local_node_id",
> rtcfg_namespace);
> res = PQexec(conn, query);
> if (PQresultStatus(res) != PGRES_TUPLES_OK)
> {
> slon_log(SLON_ERROR,
> "cannot get sl_local_node_id - %s",
> PQresultErrorMessage(res));
> PQclear(res);
> return -1;
> }
> if (PQntuples(res) != 1)
> {
> slon_log(SLON_ERROR,
> "query '%s' returned %d rows (expected
> 1)\n",
> query, PQntuples(res));
> PQclear(res);
> return -1;
> }
>
> The above are the expected failure cases, which would return negative
> numbers. The slon should have had one of those messages.
>
> What I'm expecting is that perhaps the conn info to the subscriber
> node isn't right.
>
> So you might compare:
> a) What you type in to get a psql session to the subscriber node
> to
> b) The arguments passed to slon to get it to connect.
>
> You didn't say how you're launching slon processes; I'm suspicious
> that THAT is what is breaking down.
>
> I'd prefer to address the issue on the mailing list, if possible.
> _______________________________________________
> Slony1-general mailing list
> [email protected]
> http://gborg.postgresql.org/mailman/listinfo/slony1-general
_______________________________________________
Slony1-general mailing list
[email protected]
http://gborg.postgresql.org/mailman/listinfo/slony1-general
