I am going to state a few more obvious points...because with those antennas, you should have a stronger RSSI at the client.
1. How much LMR cable (if any) are you using between the radio and the antennas? Hopefully you are not using LMR, just CAT5. 2. Is your Sector Antenna parallel to the earth or is it mechanically downtilted? Your RF may be falling short of the client. 3. After verifying the above, has your client antenna been properly aligned (tweaked)? Sully -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Cesar Sent: Tuesday, September 09, 2003 8:31 AM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] How do I improve a link? Sorry, I'm getting forgetful in my old age. The RSSI is 35% and the LQ is 65%. I'm using 90deg Sector Antennas, and yes he is within the RF path of the antenna. -C�sar -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of The Wirefree Network Sent: Tuesday, September 09, 2003 8:18 AM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] How do I improve a link? Did you state somewhere what the RSSI and LQ is? With that setup, you should be getting around 70% RSSI. What degree sector panel are you using? Does your client lie within the RF spread of the antenna? Need the RSSI/LQ to give more advice. Sully -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Cesar Sent: Tuesday, September 09, 2003 8:07 AM To: [EMAIL PROTECTED] Subject: [smartBridges] How do I improve a link? Hi everyone, I need your help/advice on improving a customer's connection. He is 10.5 miles away from my APPO (14.5 Sector antenna) and there is a clear LOS. He is using an Outdoor airBridge and a 24dBi grid antenna. At this point in time there are no amps involved, but I am seriously considering to install one at the clients site. Do you think that an Amp would solve the problem? Or do you have something in your bag of tricks that I can use? Any and all help will be greatly appreciated. TIA, -C�sar ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
