RE: [smartBridges] Omni antenna coverage

[Rudolph Worrell]

Title: Message

ï I use Comtelco's 190 degree on the SB APPO. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Derek Breiland Sent: Saturday, November 01, 2003 6:08 PM To: [EMAIL PROTECTED] Subject: Re: [smartBridges] Omni antenna coverage What manufactuer and model of 100 degree sector are you using?  Using Smartbridges APPO's? ----- Original Message ----- From: Rudolph Worrell To: [EMAIL PROTECTED] Sent: Saturday, November 01, 2003 1:02 PM Subject: RE: [smartBridges] Omni antenna coverage Certainly you do not get to add the gain in one radio.  When you put the sectors together your total output in 360 degree coverage area is 24dbi.  This is not combined in anyway it is simply what you get when you look at how many dbi's you have to cover the area that is intended.   I have 2 190 degree sectors back to back separated by about 5 ft Horizontally on a water tower(200ft).  One radio on channel 1 and the other on channel 11.  This works great for me and give me a coverage area of up to 15 miles without an amp.  I plan to introduce an amp which will most likely increase the coverage by about 5 miles or so in open space. -----Original Message----- From: Jason Baugher [mailto:[EMAIL PROTECTED]On Behalf Of Jason Baugher Sent: Saturday, November 01, 2003 1:42 PM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] Omni antenna coverage Possibly, but the assumption is that with 2 sectors, each sector is on a separate radio.  Therefore you don't get to add their gains together.   As far as the mechanical downtilt on the omni, yes, you can do that, but why would you want to, unless you are in the unique position of being on the side of a mountain with people above and below you on the slope. -----Original Message----- From: Rudolph Worrell [mailto:[EMAIL PROTECTED] Sent: Fri 10/31/2003 4:48 PM To: [EMAIL PROTECTED] Cc: Subject: RE: [smartBridges] Omni antenna coverage Yes! 2 190 degree sector gives you 380 overlapping coverage.  12dbi on one side and 12dbi on the other = 24dBi overall.   You can always tilt an antenna to create a down tilt.  With an omni you would lose coverage on the side you tilt away from. -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Jason Baugher Sent: Friday, October 31, 2003 5:35 PM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] Omni antenna coverage 2 180 deg 12dBi sectors combine to make 24dBi in 360 deg? Mechanical downtilt on an omni?   Maybe my brain is just fried, but something doesn't add up here.     Jason Baugher -----Original Message----- From: Rudolph Worrell [mailto:[EMAIL PROTECTED] Sent: Friday, October 31, 2003 4:26 PM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] Omni antenna coverage I only use Omni's at repeater sites with low number of clients.  I use 190 degree sectors for all serious connections.  12dbi in 180 or 12dbi in 360.  Well I chose  the 12 dbi in 180 each therefore giving me 24 dbi coverage for 360 degrees.   On your Omnis you should get them with a 3 degree elec downtilt or use a mechanical downtilt.  Electrical is better! -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Rob Cleminson Sent: Friday, October 31, 2003 5:13 PM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] Omni antenna coverage I too am running with a 12dbi Omni at about 150â  - customers at about 2-4km get a good signal but the closer you get the worse the signal gets â I am about to swap out and try a 9dbi Omni to see if the RF pattern improves for the clients that are closer. Failing this I will chuck the omniâs and use sectored antennaâs   Rob     -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ian Ellison Sent: 31 October 2003 14:57 To: [EMAIL PROTECTED] Subject: Re: [smartBridges] Omni antenna coverage   I am currently running airPointPro Outdoor units with Comet GP24-3 Omni's, which is a 12 db antenna.  I am servicing customers as far as 5 miles away with sufficient results.  However, the equipment is about 150' above ground level which im sure helps.  Good luck. Ian Derek Breiland wrote: Up to this point I have been running off of one tower with 3 sectors.  I am looking at putting an addtional AP up about 6 miles from this tower to penetrate into a community of homes that will otherwise be difficult to cover due to the number of obstructions not to mention their elevation on the map leaves a little to be desired.  It will also enable me to install a less expensive CPE at the customer site if I can bring the AP closer to the customer making the service a bit of an easier sell.   I want to utilize an omni antenna in this area.  I have not yet decided what to backhaul with yet but I am considering an APPO to the new XO2 at the remote.  I can use one radio on the XO2 for the backhaul on one channel and the other radio for the access to the customers.  I am not a big fan of repeaters unless absolutley necessary.  It seems that most complaints on this site have the word "repeater" in the paragraph so I will try and stay away from it.   My question is to anyone currently working with onmi antennes on an AP.  What ranges can I expect for the various dB omni antennas?  9dB seems small to me, 12dB is maybe the ticket, 15db - way overkill?  I do not want the pattern to get too large to cause problems with my main tower.  I am looking at trying to get out no more than 3 miles for the AP.  The AP and omni will be mounted on a 40'-50' existing tower.  Also has anyone had better results with one manufacturer over the other with the same dB antenna?   Any suggestions are greatly appreciated.  I will be doing more and more of this so I would like to get it right the first time based on others experiences in already doing it.