Never mind, if that were the case you would not be able to pass traffic across the link.
----- Original Message ----- From: "[EMAIL PROTECTED]" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Saturday, November 22, 2003 9:32 PM Subject: Re: [smartBridges] Point to Point can't access > Is client to client communciation disabled? > > ----- Original Message ----- > From: "Eje Gustafsson" <[EMAIL PROTECTED]> > To: "Shane Warren" <[EMAIL PROTECTED]> > Sent: Saturday, November 22, 2003 8:55 PM > Subject: Re: [smartBridges] Point to Point can't access > > > > What port do you have set as primary port ? I would assume the > > ethernet.. If you check out the manual you will find out a few very > > important things about the primary port. > > > > Best regards, > > Eje "Aya" Gustafsson mailto:[EMAIL PROTECTED] > > The Family Entertainment Network http://www.fament.com > > Phone : 620-231-7777 Fax : 240-376-7272 > > - Your Full Time Professionals - > > Online Store http://www.wisp-router.com/ > > MikroTik, Star-OS, PACWireless, EnGenius, RF Industries > > -- > > > > SW> We have a customer that said about 3 months ago they were not able to > see > > SW> there point to point shot anymore on simple NMS or simple monitor. > > SW> Yesterday we went out there to see if we could fix there problem with > no > > SW> luck. From there office you can see the APPO's on the tower, but you > can not > > SW> see the office to the tower point to point. They seem to be > invisible, you > > SW> can't ping them either. If you unplug either side of the point to > point > > SW> from the switch and plug it directly into your laptop you can see the > point > > SW> to point then but not the other 3 APPO's. Everything is set up > correctly, > > SW> we tried it in wireless bridge mode, and APPO in AP mode - APPO in CB > mode, > > SW> neither way made any difference, we double checked all the numbers and > > SW> everything is the way it is supposed to be. Everything works, I just > don't > > SW> know why all of a sudden we can't ping the units or get into them > remotely. > > SW> We also tried resetting them back to factory default and reprogramming > them, > > SW> the only thing different from the 3 APPO's on the tower and the point > to > > SW> point is the there is not WEP key in the point to point, but I don't > think > > SW> that should make a difference in monitoring them or accessing them > remotely. > > SW> Any help would be greatly appreciated. > > > > SW> Shane Warren > > SW> ATW Wireless > > > > > > SW> The PART-15.ORG smartBridges Discussion List > > SW> To Join: mailto:[EMAIL PROTECTED] (in the body type > > SW> subscribe smartBridges <yournickname> > > SW> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > > SW> Archives: http://archives.part-15.org > > > > -- > > [This E-mail scanned for viruses by Declude Virus] > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > > Archives: http://archives.part-15.org > > > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
