Device aka:
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Get access with the following parameter, as mentioned in the wiki:
# smartctl -d usbjmicron /dev/sdx
The attached Smart report tells:
Device is: In smartctl database [for details use: -P show]
A view into your database on the website tells, that it is not in there,
only just a similar model.
That's why I submit this report as addition to your very helpful
database.
Thx and best regards.
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.0-gentoo] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Firmware Version: 0002BSM1
User Capacity: 500.107.862.016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 1.5 Gb/s
Local Time is: Wed Aug 17 19:06:13 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Write SCT (Get) Feature Control Command failed: Read of ATA output registers
not implemented [JMicron]
Wt Cache Reorder: Unknown (SCT Feature Control command failed)
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 144) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 118 099 006 - 169452068
3 Spin_Up_Time PO---- 097 097 000 - 0
4 Start_Stop_Count -O--CK 099 099 020 - 1215
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 2
7 Seek_Error_Rate POSR-- 075 060 030 - 38220474
9 Power_On_Hours -O--CK 096 096 000 - 4123
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 099 037 020 - 1172
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 0
188 Command_Timeout -O--CK 100 094 000 - 21475164331
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 067 054 045 - 33 (Min/Max 25/33)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 12
192 Power-Off_Retract_Count -O--CK 100 100 000 - 861
193 Load_Cycle_Count -O--CK 075 075 000 - 50095
194 Temperature_Celsius -O---K 033 046 000 - 33 (0 12 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 049 044 000 - 169452068
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands not
implemented [JMicron]
Read GP Log Directory failed
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 SL R/O 5 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 SL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 SL R/O 1 SATA NCQ Queued Error log
0x11 SL R/O 1 SATA Phy Event Counters log
0x21 SL R/O 1 Write stream error log
0x22 SL R/O 1 Read stream error log
0x80-0x9f SL R/W 16 Host vendor specific log
0xa1 SL VS 20 Device vendor specific log
0xa8 SL VS 65 Device vendor specific log
0xa9 SL VS 1 Device vendor specific log
0xc0 SL VS 1 Device vendor specific log
0xe0 SL R/W 1 SCT Command/Status
0xe1 SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
SMART Error Log Version: 1
No Errors Logged
SMART Extended Self-test Log (GP Log 0x07) not supported
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 4123 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 33 Celsius
Power Cycle Min/Max Temperature: 25/33 Celsius
Lifetime Min/Max Temperature: 12/46 Celsius
Under/Over Temperature Limit Count: 0/11
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/ 0 Celsius
Min/Max Temperature Limit: 0/ 0 Celsius
Temperature History Size (Index): 128 (0)
Index Estimated Time Temperature Celsius
1 2016-08-17 16:59 31 ************
... ..( 27 skipped). .. ************
29 2016-08-17 17:27 31 ************
30 2016-08-17 17:28 32 *************
... ..( 11 skipped). .. *************
42 2016-08-17 17:40 32 *************
43 2016-08-17 17:41 33 **************
... ..( 44 skipped). .. **************
88 2016-08-17 18:26 33 **************
89 2016-08-17 18:27 ? -
90 2016-08-17 18:28 23 ****
91 2016-08-17 18:29 24 *****
92 2016-08-17 18:30 25 ******
93 2016-08-17 18:31 26 *******
94 2016-08-17 18:32 27 ********
95 2016-08-17 18:33 27 ********
96 2016-08-17 18:34 28 *********
97 2016-08-17 18:35 29 **********
98 2016-08-17 18:36 30 ***********
99 2016-08-17 18:37 30 ***********
100 2016-08-17 18:38 31 ************
101 2016-08-17 18:39 31 ************
102 2016-08-17 18:40 32 *************
103 2016-08-17 18:41 32 *************
104 2016-08-17 18:42 32 *************
105 2016-08-17 18:43 33 **************
106 2016-08-17 18:44 33 **************
107 2016-08-17 18:45 34 ***************
108 2016-08-17 18:46 34 ***************
109 2016-08-17 18:47 34 ***************
110 2016-08-17 18:48 33 **************
111 2016-08-17 18:49 ? -
112 2016-08-17 18:50 33 **************
113 2016-08-17 18:51 ? -
114 2016-08-17 18:52 33 **************
115 2016-08-17 18:53 32 *************
116 2016-08-17 18:54 32 *************
117 2016-08-17 18:55 ? -
118 2016-08-17 18:56 25 ******
119 2016-08-17 18:57 25 ******
120 2016-08-17 18:58 29 **********
121 2016-08-17 18:59 31 ************
122 2016-08-17 19:00 31 ************
123 2016-08-17 19:01 31 ************
124 2016-08-17 19:02 32 *************
125 2016-08-17 19:03 33 **************
... ..( 2 skipped). .. **************
0 2016-08-17 19:06 33 **************
Write SCT (Get) Error Recovery Control Command failed: Read of ATA output
registers not implemented [JMicron]
SCT (Get) Error Recovery Control command failed
Device Statistics (GP/SMART Log 0x04) not supported
ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: 48-bit ATA commands not
implemented [JMicron]
Read SATA Phy Event Counters failed
------------------------------------------------------------------------------
_______________________________________________
Smartmontools-database mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
