Generic USB 3.0 Enclosure for 2.5" SATA disks with UASP Support.
Controller=JMicron JMS578
VID=0x152d
PID=0x0578
Bridge unknown, but enclosure answers to "-d sat". Output of "-x" after
conducting "-t short" (following
https://www.smartmontools.org/wiki/FAQ#MyATASATAdriveisnotinthesmartctlsmartddatabase)
attached.
Cheers
Marco
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.4.0-53-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9320325AS
Serial Number: 6VD66V28
LU WWN Device Id: 5 000c50 02b8f55d5
Firmware Version: 0003SDM1
User Capacity: 320.072.933.376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Wed Mar 29 09:59:13 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 95) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 119 078 006 - 219752487
3 Spin_Up_Time PO---- 099 099 000 - 0
4 Start_Stop_Count -O--CK 097 097 020 - 3646
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 1
7 Seek_Error_Rate POSR-- 079 060 030 - 94433544
9 Power_On_Hours -O--CK 096 096 000 - 3752
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 097 097 020 - 3628
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 001 001 000 - 18002
188 Command_Timeout -O--CK 100 099 000 - 4295032841
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 081 049 045 - 19 (Min/Max 17/19)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 598
192 Power-Off_Retract_Count -O--CK 100 100 000 - 33
193 Load_Cycle_Count -O--CK 078 078 000 - 44775
194 Temperature_Celsius -O---K 019 051 000 - 19 (0 8 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 059 053 000 - 219752487
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
254 Free_Fall_Sensor -O--CK 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 SATA NCQ Queued Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters log
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 65 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xb0 GPL VS 2864 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 18120 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 18120 [19] occurred at disk power-on lifetime: 3273 hours (136 days + 9
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 96 3b 25 00 00 Error: UNC at LBA = 0x02963b25 =
43399973
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 03 00 80 00 00 02 90 8b 00 e0 00 08:27:21.139 READ DMA EXT
25 00 03 00 80 00 00 02 90 8a 80 e0 00 08:27:21.135 READ DMA EXT
25 00 03 00 80 00 00 02 80 97 00 e0 00 08:27:02.130 READ DMA EXT
25 00 03 00 80 00 00 02 80 96 80 e0 00 08:27:02.118 READ DMA EXT
25 00 03 00 80 00 00 02 70 a0 00 e0 00 08:26:43.072 READ DMA EXT
Error 18119 [18] occurred at disk power-on lifetime: 3261 hours (135 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 c2 89 40 00 00 Error: UNC at LBA = 0x02c28940 =
46303552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 02 c2 89 40 40 00 10:40:18.392 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:18.356 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 10:40:18.355 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 10:40:18.354 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:18.354 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
Error 18118 [17] occurred at disk power-on lifetime: 3261 hours (135 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 c2 89 40 00 00 Error: UNC at LBA = 0x02c28940 =
46303552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 02 c2 89 40 40 00 10:40:15.938 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:15.902 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 10:40:15.901 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 10:40:15.900 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:15.900 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
Error 18117 [16] occurred at disk power-on lifetime: 3261 hours (135 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 c2 89 40 00 00 Error: UNC at LBA = 0x02c28940 =
46303552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 02 c2 89 40 40 00 10:40:13.466 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:13.429 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 10:40:13.428 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 10:40:13.428 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:13.427 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
Error 18116 [15] occurred at disk power-on lifetime: 3261 hours (135 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 c2 89 40 00 00 Error: UNC at LBA = 0x02c28940 =
46303552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 02 c2 89 40 40 00 10:40:10.995 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:10.956 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 10:40:10.955 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 10:40:10.954 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:10.954 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
Error 18115 [14] occurred at disk power-on lifetime: 3261 hours (135 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 c2 89 40 00 00 Error: UNC at LBA = 0x02c28940 =
46303552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 02 c2 89 40 40 00 10:40:08.518 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:08.480 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 10:40:08.479 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 10:40:08.478 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:08.478 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
Error 18114 [13] occurred at disk power-on lifetime: 3261 hours (135 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 c2 89 40 00 00 Error: UNC at LBA = 0x02c28940 =
46303552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 02 c2 89 40 40 00 10:40:06.050 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:05.802 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 10:40:05.800 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 10:40:05.800 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:05.799 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
Error 18113 [12] occurred at disk power-on lifetime: 3261 hours (135 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 02 c2 89 40 00 00 Error: UNC at LBA = 0x02c28940 =
46303552
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 02 c2 89 40 40 00 10:40:03.293 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:03.257 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 10:40:03.255 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 10:40:03.255 SET FEATURES [Set
transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 10:40:03.254 READ NATIVE MAX
ADDRESS EXT [OBS-ACS-3]
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 3752 -
# 2 Short offline Aborted by host 20% 3685 -
# 3 Extended offline Aborted by host 70% 3286 -
# 4 Short offline Completed without error 00% 3282 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 19 Celsius
Power Cycle Min/Max Temperature: 17/19 Celsius
Lifetime Min/Max Temperature: 8/51 Celsius
Under/Over Temperature Limit Count: 0/3
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/ 0 Celsius
Min/Max Temperature Limit: 0/ 0 Celsius
Temperature History Size (Index): 128 (3)
Index Estimated Time Temperature Celsius
4 2017-03-29 07:52 33 **************
... ..( 63 skipped). .. **************
68 2017-03-29 08:56 33 **************
69 2017-03-29 08:57 34 ***************
... ..( 13 skipped). .. ***************
83 2017-03-29 09:11 34 ***************
84 2017-03-29 09:12 ? -
85 2017-03-29 09:13 15 -
86 2017-03-29 09:14 16 -
87 2017-03-29 09:15 17 -
88 2017-03-29 09:16 18 -
89 2017-03-29 09:17 19 -
90 2017-03-29 09:18 ? -
91 2017-03-29 09:19 20 *
92 2017-03-29 09:20 ? -
93 2017-03-29 09:21 20 *
94 2017-03-29 09:22 ? -
95 2017-03-29 09:23 23 ****
96 2017-03-29 09:24 23 ****
97 2017-03-29 09:25 25 ******
98 2017-03-29 09:26 26 *******
99 2017-03-29 09:27 27 ********
100 2017-03-29 09:28 27 ********
101 2017-03-29 09:29 27 ********
102 2017-03-29 09:30 28 *********
103 2017-03-29 09:31 ? -
104 2017-03-29 09:32 28 *********
... ..( 3 skipped). .. *********
108 2017-03-29 09:36 28 *********
109 2017-03-29 09:37 29 **********
110 2017-03-29 09:38 29 **********
111 2017-03-29 09:39 30 ***********
... ..( 2 skipped). .. ***********
114 2017-03-29 09:42 30 ***********
115 2017-03-29 09:43 29 **********
116 2017-03-29 09:44 29 **********
117 2017-03-29 09:45 30 ***********
118 2017-03-29 09:46 30 ***********
119 2017-03-29 09:47 30 ***********
120 2017-03-29 09:48 31 ************
121 2017-03-29 09:49 31 ************
122 2017-03-29 09:50 30 ***********
123 2017-03-29 09:51 30 ***********
124 2017-03-29 09:52 30 ***********
125 2017-03-29 09:53 31 ************
126 2017-03-29 09:54 31 ************
127 2017-03-29 09:55 31 ************
0 2017-03-29 09:56 ? -
1 2017-03-29 09:57 17 -
2 2017-03-29 09:58 18 -
3 2017-03-29 09:59 19 -
SMART WRITE LOG does not return COUNT and LBA_LOW register
SCT (Get) Error Recovery Control command failed
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
Smartmontools-database mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
