I do not see that you have received any answers to your question.  Perhaps
you did offline.  Several factors could be involved.  The fact that the
plane went "straight up" may be because the hook is behind  (or too close
to) the CG and/or because the wind was very strong.  But usually, the line
will unhook.  Perhaps, your line is too short, i.e., the model never loses
any line tension and is therefore unable to de-couple.  Unless you are
trying to do a 'contest' launch, your model should level off with little or
no line tension.  You then fly forward (into the wind) and the line comes
off (sometimes this requires a dive).   You say, "... short tubing ...", but
did not say about the line length - it should be 5 or more times longer than
the tubing.  I suspect you are using too short of a line for the tubing
length and you never loose enough tension.  The best advice I can give you
though - is;  find an experience TD pilot and get hands on help.
Regis

-----Original Message-----
From:   Russell Rinn [mailto:[EMAIL PROTECTED]]
Sent:   Saturday, February 26, 2000 6:26 PM
To:     [EMAIL PROTECTED]
Subject:        [RCSE] High Start hook won't release

Woe is me...or how I tried to learn to fly

Ok, more beginner questions, but first my tale.  (If you don't want to read
all the stuff that follows, here's my question:  Why wouldn't my highstart
let go of the plane?  I used a key ring to attach my start to the planes
hook.  Any ideas?  I have plenty of time to read your answers as this thing
woon't fly for along time

Ok, I built my EPP trainer from Dave's.  As some of you may remember I
tried to fly in very gusty winds with an unbalanced plane.  With the advice
of the people on this list I was able to balance my plane nicely.  I tossed
it by hand to check it out and it glided pretty good.

I then bought some surgical tubing and line to build my high start, or in
my case, because of my short tubing, a low start.

Ok, here it goes first launch.  Pull back on the plane, position it with
the nose just angled up slightly and let her go.  Whoosh, straight up into
the air, it looked pretty good until...

it never let go of the line.  Based on what comes up must come down, it
came down in a big way.  Still attached to the high start until about 10'
from the ground. And about 100 mph!  Right into the ground.  hard!  Ok,
well, I'm glad this is a foam plane because there was no damage.  Ok, let's
try this again.  Once again, it came down agian, and again, and again.  I
think I tried about 6 times with the same result.  Ok, this was getting
hard to take.  My plane was starting to take on a different shape.  These
very hard crashes were taking their toll.  There is a definite limit to
what this stuff can take.  After one more attempt both my servos were
destroyed.  (After I took them apart today I saw that they had broken gear
teeth.  can you buy replacement gear sets?)

Ok, I still wanted to know what was causing this so I just powered off the
radio equipment and decided to launch this thing until it worked.  (Maybe
not the best idea.)

Ok, I thought perhaps the line was too light and just never fell off at the
apex.  So I strapped some weight to the ring that hooked onto the planes
hook.  Ok, BAD idea as the plane never even let go of the high start.  So
my last thought was to bend the planes hook down at an angle.  I figured it
would slip off easier that way.  It worked!  I had launched my plane!  My
plane was in the air literally on it's own as the controls were shot.  I
just watched as it went straight up in the air and then behind me by about
300'.  It almost made it past the trees.  Flying planes must be like flying
a kite as the plane went right to the trees.

Ok, I retrieved my plane with no problem.  I took it home to do the repairs
and my story gets better (or worse).

Damage report: Both servos broken.  Ok, I have replacements.  The
connectors on my receiver were also shattered.  Ok, it gets really bad
here.  The power connector was broken.  Even though I have 20 years
experience in electronics I just looked at the angle the wires were bent
and decided how they should go back in the connector.  I wasn't 100% sure
but decided to power it up anyway.  MELTDOWN.  Smoke started to pour from
the plane.  The battery generates alot of heat when it's shorted out.

So the total toll from my first attempt at flight:  2 servos, 1 battery, 1
switch and probably one receiver.  Not to mention lots of structural
problems with my foam plane.

Ok, now my question:  Why wouldn't my highstart let go of the plane?  I
used a key ring to attach my start to the planes hook.  Any ideas?  I have
plenty of time to read your answers as this thing woon't fly for along time!

Thanks for your help.

Still smiling,

Russ--

RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and
"unsubscribe" requests to [EMAIL PROTECTED]


RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and 
"unsubscribe" requests to [EMAIL PROTECTED]

Reply via email to