Hello Joe 
   I think that the bow that you found is fine. It seams to have a metal bar 
on top that could be a problem with insulation of the cutting wire but it 
looks fine. 
  I will state this as simple as possible. Why I do not like Feather cut!  A 
few years ago there was a seminar on composite model building at a school 
near 
Hawaiian Gardens Long Beach area. One of the sponsors was Michael Tabby of 
Superior Balsa. I planed to attend and called Mr. Tabby and ask him if the 
seminar was going to be video taped. His reply was that he had not had time 
to set it up. I make videos and offered to film the session. He said he would 
be pleased if I would do that. So I gathered up my crew, camera equipment and 
all and drove from 
San Jose to Long Beach. When I arrived and started to set up the tripods and 
cameras I was suddenly interrupted by a Mr. Rodger Chasten shouting from the 
podium that 
"THIS IS CLOSED TO VIDEO" I explained that I had been Invited to film the 
seminar for Mr. Tabby. His reply was "OH THAT WAS A MISTAKE." So I did not 
film the seminar. I was promised a tape that Mr. Chasten had filmed for 
compensation for my trouble. I never received it. Now I watched the Feather 
Cut demonstration. I will list it, s faults. 
1. The little wheel on the bow is no good.
2. Power attached by alligator clips. is no good
3. Pull wire is also power source. is no good_.I will list it good points 
also.

1. It folds up.
2. It has a nice anodized finish.  What will make it better. I will list

1. Needs to be supported by a bungi cord that will allow the cutting arm to 
pass over  the edge of the foam block being cut.
2. Needs to have the arms of the bow to be insulated from the metal frame so 
that the power can be applied directly to the bow.
3. Connect power to the bow as in 2 above.
4. Remove the little wheel and put it on something that needs it.
5. Airfoil templets need to have a stop on the rear to keep the bow from 
falling over the edge of the cutting table. 
  There are other small refinements but this is the most important changes 
that need to be made. It can be used as it is designed but it will be a whole 
lot of trouble. I made my first hot wire cutter in the late 60's at that time 
we used a two person system and a single template. I had several moves from 
the Bay Area to LA
and to San Diego area where I worked on the Atlas missile system. Then I went 
to Edward's AFB and did ground support on the X-15 and also the unmanned 
lifting body then to Vandenberg and worked on the Titan. After that I 
returned to the bay area and worked at Lockeed in Instrument calibration. I 
have been in the bay area since then I worked for Stanford Research Institute 
building sensors for atomic research in Nevada test sites. I helped build the 
Stanford linear accelerator. I went to work at the University of Santa Clara 
for 12 years after that I started contracting with Westinghouse where I 
worked on things like a homopolar generator a rail gun and  in three days I 
worked nonstop on a device to disarm a warhead on a missile that had failed a 
test in a silo in Wyoming and was in danger of detonating. I prevented that.
  So what does this have to do with anything. I am now retired. I am 68 years 
old and I am diabetic, have had a four way heart bypass. Will most likely not 
be around to much longer. I enjoy RC sailplanes, I like the people that fly 
them. I enjoy cutting foam wings. I do not like to see modelers taken 
advantage of. I have more experance than most could ever hope for and I will 
help any person that needs it. So fault me if you may but I do not like 
Feather Cut or Its Maker and I think that I am intitled.
 I want to thank all on this list and excuse the length of this reply but it 
is my final word on this subject. Thank you very much.  Ex USAF Del Brengman
RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and 
"unsubscribe" requests to [EMAIL PROTECTED]

Reply via email to