Having recently completed a cost-to-coast trip via commercial airline I
thought I'd pass on my experience and some tips I learned.

To get ready for the trip:
I obtained a plastic Golf-Guard golf bag carrier from my local K-mart
($39.95) and a large piece of 4" thick foam from the local fabric store. I
cut the foam into 2 sections, shaped it to "fit" the bottom of the case
using an electric carving knife, and slit it for the wings. The foam slides
over the wings from each end and then drops down into the case. Stabs, etc
were then slipped into the same slit holding the wings. A couple of pop
rivets, cable holders, and short bungees held everything in place quite
securely. The bottom "end" of the case (if you were to stand it up) had
plenty of clearance for my Nova 250S Charger w/ 2 battery packs in side its
box, and for my Alpha4 charger...So in they went. I laid a piece of 1" foam
in the top of the case and placed the 2 fuselages in. I then cut a piece of
styrofoam (maybe a couple of inches thick) to fit the into the top of the
case (again at what would be the "bottom end" if you were to stand it up)
and dug out some of the foam so the spinners would slip down into the
styrofoam (to hold the nose of the planes securely). A few more pop rivets,
cable holders, and short bungees were used to secure each fuse' in place at
appx the middle of the fuse. I took 1 more piece of 1" foam and laid it over
the tail end of the fuselages and again, secured it with bungees. Closed the
case and shook the case, bumped it, etc...WOW...It works! Now to see what
the airlines will think/do <G>!

At the airport:
I got to the counter and checked-in...No questions asked as to what was in
the case. Security though was another matter. I had forgotten to remove the
small tools that I carry in my TX case and they were definitely not happy
about that (my fault). Security suggested that I check the TX case and I
said absolutely not, they could remove anything the wanted and I'd get it
into my checked luggage somehow (not that I couldn't have done w/o it at the
other end mind you). No problem they said. Back to the agent at the ticket
counter, explaining the problem, and they managed to locate my checked bags
and slip the envelope (provided by security) into the bags. So here's what
you DO NOT want to pack into carry-on luggage...screwdrivers, exactos,
needlenose pliers, forceps, hemostats, etc...basically ANYTHING with a point
or sharp edge. The spare battery packs were ok, the Tx was OK, but the other
stuff was a no-no!

Boarding the plane:
I had a window seat so I was able to watch as they loaded the luggage. Golf
bags appear to go on close to the end of the loading and I watched (and
cringed) as they tossed the bag onto the conveyer. Oh well, not much I can
do now except enjoy a flight from ROC to ORD to DFW to SAC (not the most
direct flight I realize).

At the other end:
Yep...everything got there when I did! The golf bag looked intact too.
Arrived at my family's house and, once settled, checked my "toys" to find
out that everything had come through with flying colors. A couple of days
later I introduced my nephews to the hobby and I think they're hooked. They
had no idea how much pleasure you can get out of tooling around the skies in
search of lift!

In short, when traveling via commercial airlines...If you can cut, poke, or
pry with it...Simply pack it into your checked luggage and you should be
just fine!

-Sheldon-
YNT uDesign

A Supporter of the 2002 Soaring Nationals

RCSE-List facilities provided by Model Airplane News.  Send "subscribe" and 
"unsubscribe" requests to [EMAIL PROTECTED]

Reply via email to