Chuck, You are a better flier than I am to feel that difference in of all things a Sailaire, when I watch guys put in 5 pound blocks for ballast and say they fly no different, I cannot imagine that two wing servos would make much of a difference. If set up correctly you get crisper action, more adjustability, and more accurate throws. I am not saying use 2 ounce servos, how about .5 ounce ones with good tight pushrod set ups and that will more than do the job. I will never make another spoiler ship with out this set up, my Skybench Aerotech Legionaire will be next, I will use JR217's to drive them.
Marc --- Original Message --- From: Chuck Anderson <[EMAIL PROTECTED]> Sent: Tue, 12 Oct 2004 20:40:32 -0500 To: [EMAIL PROTECTED] Subject: re: [RCSE] Sailaire Spoiler Servo Mount > Sorry but I must disagree. I have used both and prefer pull strings with > servos in the nose where the weight is needed instead of outboard in the > wing where it isn't needed. I have used pull strings for spoiler control > for 30 years. I built a Sailaire in 1978 and used pull strings without > problems. I sold it a few years later and tried to buy it back in 1994 to > fly in the first Nostalgia contest at Muncie without success. I was > finally able to buy it back a couple of years ago and found that the > spoilers had been converted to wing servos. A good pull string system is > easier to set up and adjust. When I recover the wing, I will take the > servos out and convert it back to the way I built it 26 years ago. I only > use wing spoiler servos for three piece wings with spoilers in the outboard > panels where pull strings are impractical. > > Chuck Anderson > > At 08:15 PM 10/12/2004, you wrote: > >If you are radio capable, mount a servo in each wing and then there is no > >plumbing and much more accurate and controllable spoilers. > > > > > >Mard > > > > > > > > > >--- Original Message --- > >From: Richard Jones <[EMAIL PROTECTED]> > >Sent: Tue, 12 Oct 2004 21:00:58 -0400 > >To: [EMAIL PROTECTED] > >Subject: [RCSE] Sailaire Spoiler Servo Mount > > > > > Hi > > > I'm currently building a dchobby's Sailaire and the plans are not very > > > clear about where the servo for the spoilers should be mounted. > > > > > > The control tubes for the spoilers exit the wings at quite a sharp angle > > > so I'm guessing the servo must be quite far forward? > > > > > > Also I've seen a few posts mentioning actually putting mini servos in the > > > wings for the spoilers, is this a good idea? > > > > > > If wanyone has a picture of the servo bay of a sailaire could you please > > > send it to me? > > > > > > Thanks > > > Richard > > > > > > -- > > > Using Opera's revolutionary e-mail client: http://www.opera.com/m2/ > > > RCSE-List facilities provided by Model Airplane News. Send "subscribe" > > and "unsubscribe" requests to [EMAIL PROTECTED] Please note > > that subscribe and unsubscribe messages must be sent in text only format > > with MIME turned off. > > > > > > >Marc Gellart, Marketing Representative > >704-473-9292 Cell Phone > >618-654-8101 Home and Fax > >RCSE-List facilities provided by Model Airplane News. Send "subscribe" > >and "unsubscribe" requests to [EMAIL PROTECTED] Please note > >that subscribe and unsubscribe messages must be sent in text only format > >with MIME turned off. > > RCSE-List facilities provided by Model Airplane News. Send "subscribe" and > "unsubscribe" requests to [EMAIL PROTECTED] Please note that subscribe and > unsubscribe messages must be sent in text only format with MIME turned off. > Marc Gellart, Marketing Representative 704-473-9292 Cell Phone 618-654-8101 Home and Fax RCSE-List facilities provided by Model Airplane News. Send "subscribe" and "unsubscribe" requests to [EMAIL PROTECTED] Please note that subscribe and unsubscribe messages must be sent in text only format with MIME turned off.