Thanks Mark and to the others who responded.
I've concluded that ship building in a bottle will be worth the effort.
-----Original Message-----
From: Mark Williams <[EMAIL PROTECTED]>
To: [EMAIL PROTECTED]; [email protected]
Sent: Mon, 13 Jun 2005 19:41:35 -0500
Subject: Re: [RCSE] Ballast suggestions, Long!
Dan,
What I have done in my Shappire is this. Make up some 1/2" K & S brass
slugs at the increments you want to be able to add weight. Fill with
your
weight of choice, lead shot/epoxy, tungsten powder, or melted tire
weights.
Obtain some Estes Rocket tubes, # BT-5. These have a nominal ID of
.518",
perfect for a slip fit on the K & S tubing. Just do a search on the
Net,
found multiple suppliers or look in a good hobby shop if you can find
one
these days. Make a plug to close the aft end of the tube, so the slugs
don't fly all the way to the tail feathers when inserted. I like
lite-ply,
light weight and bonds to the tubes with thin CA like crazy.
If you want to really strengthen the tube wrap it with 1.5 oz.
fiberglass
cloth using CA. Or, you can just soak the inside with CA. If you CA
the
inside, you might need to ream the tube after the CA sets with a piece
of
1/2" brass tube. I have done either and both, with both the cloth and
CA
the tubes are really STIFF and LIGHT. That is what I just recently
installed in my Eraser. I recommend a brass tube collar CA'd to the
paper
tube where you plan to have a piano wire retainer to carry landing
shock
loads. The Eraser tube weighed less than 3/8 oz. with the collar.
If you are installing this in the Sapphire I sold you and still have
the pin
type landing skeg, I would recommend two tubes. These go either side
of the
landing skeg. Make a bulkhead for the aft portion of the tubes and the
forward portion of the tubes. Install all of this in your fuselage so
the
full ballast load rests at the CG. Don't you just love building a ship
in a
bottle?
Now make up some 3/8" hard balsa spacers to your liking so you can use
less
than the full load. 3/8" balsa will fit perfectly if you just break
the
corners. Just make sure the spacers keep the ballast at the CG. I
will
also recommend that if you require a balsa spacer at the retainer pin
like I
do, CA a piece of brass shim stock on the end that contacts the piano
wire
retainer pin to prevent crushing when dorking.
This is all easier to see than to write. The next time we meet up let
me
know so I can bring my Sapphire and show how it looks. This set-up
allows
me to carry 15.5 oz. of ballast in my Sapphire if desired. It's not an
even
pound because I am using the slugs I made 20+ years ago. The Eraser
set-up
carries the same load in one tube, all centered on my favorite CG.
It's
nice having only one ballast system in the flight box for all of your
arrows!
Mark W.
----- Original Message -----
From: <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Sunday, June 12, 2005 7:03 PM
Subject: [RCSE] Ballast suggestions
Gent's
I'd like to add a provision for ballast to my Sapphire.
Looking for suggestions on tube/plug combinations that fit nicely.
Didn't have a whole lot of luck at Home Depot.
Dan
RCSE-List facilities provided by Model Airplane News. Send
"subscribe"
and "unsubscribe" requests to [EMAIL PROTECTED] Please
note
that subscribe and unsubscribe messages must be sent in text only
format
with MIME turned off. Email sent from web based email such as
Hotmail and
AOL are generally NOT in text format
RCSE-List facilities provided by Model Airplane News. Send "subscribe"
and
"unsubscribe" requests to [EMAIL PROTECTED] Please note that
subscribe and unsubscribe messages must be sent in text only format
with MIME
turned off. Email sent from web based email such as Hotmail and AOL
are
generally NOT in text format
RCSE-List facilities provided by Model Airplane News. Send "subscribe" and
"unsubscribe" requests to [EMAIL PROTECTED] Please note that subscribe and unsubscribe
messages must be sent in text only format with MIME turned off. Email sent from web based email
such as Hotmail and AOL are generally NOT in text format