Hi Matthias,
Matthias Fuchs wrote:
> This patch adds support for SJA1000 based PCI CAN interface cards
> from electronic system design gmbh.
>
> Two changes have been done on the common code:
> - esd boards must not have the 2nd local interupt enabled (PLX9030/9050)
> - a new path for PLX9056/PEX8311 chips has been added
>
> In detail the following additional boards are now supported:
>
> CAN-PCI/200 (PCI)
> CAN-PCI/266 (PCI)
> CAN-PMC266 (PMC module)
> CAN-PCIe/2000 (PCI Express)
> CAN-CPCI/200 (Compact PCI, 3U)
> CAN-PCI104 (PCI104)
>
> Signed-off-by: Matthias Fuchs <[email protected]>
Could you also please update the corresponding Kconfig entry. Apart
from that, the patch looks good.
Thanks,
Wolfgang.
> drivers/net/can/sja1000/plx_pci.c | 110
> ++++++++++++++++++++++++++++++++++---
> 1 files changed, 101 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/net/can/sja1000/plx_pci.c
> b/drivers/net/can/sja1000/plx_pci.c
> index 6b46a63..42602e9 100644
> --- a/drivers/net/can/sja1000/plx_pci.c
> +++ b/drivers/net/can/sja1000/plx_pci.c
> @@ -40,7 +40,10 @@ MODULE_DESCRIPTION("Socket-CAN driver for PLX90xx
> PCI-bridge cards with "
> MODULE_SUPPORTED_DEVICE("Adlink PCI-7841/cPCI-7841, "
> "Adlink PCI-7841/cPCI-7841 SE, "
> "Marathon CAN-bus-PCI, "
> - "TEWS TECHNOLOGIES TPMC810");
> + "TEWS TECHNOLOGIES TPMC810, "
> + "esd CAN-PCI/CPCI/PCI104/200, "
> + "esd CAN-PCI/PMC/266, "
> + "esd CAN-PCIe/2000")
> MODULE_LICENSE("GPL v2");
>
> #define PLX_PCI_MAX_CHAN 2
> @@ -53,7 +56,7 @@ struct plx_pci_card {
>
> #define PLX_PCI_CAN_CLOCK (16000000 / 2)
>
> -/* PLX90xx registers */
> +/* PLX9030/9050/9052 registers */
> #define PLX_INTCSR 0x4c /* Interrupt Control/Status */
> #define PLX_CNTRL 0x50 /* User I/O, Direct Slave Response,
> * Serial EEPROM, and Initialization
> @@ -65,6 +68,12 @@ struct plx_pci_card {
> #define PLX_PCI_INT_EN (1 << 6) /* PCI Interrupt Enable */
> #define PLX_PCI_RESET (1 << 30) /* PCI Adapter Software Reset */
>
> +/* PLX9056 registers */
> +#define PLX9056_INTCSR 0x68 /* Interrupt Control/Status */
> +
> +#define PLX9056_LINTI (1 << 11)
> +#define PLX9056_PCI_INT_EN (1 << 8)
> +
> /*
> * The board configuration is probably following:
> * RX1 is connected to ground.
> @@ -100,6 +109,13 @@ struct plx_pci_card {
> #define ADLINK_PCI_VENDOR_ID 0x144A
> #define ADLINK_PCI_DEVICE_ID 0x7841
>
> +#define ESD_PCI_SUB_SYS_ID_PCI200 0x0004
> +#define ESD_PCI_SUB_SYS_ID_PCI266 0x0009
> +#define ESD_PCI_SUB_SYS_ID_PMC266 0x000e
> +#define ESD_PCI_SUB_SYS_ID_CPCI200 0x010b
> +#define ESD_PCI_SUB_SYS_ID_PCIE2000 0x0200
> +#define ESD_PCI_SUB_SYS_ID_PCI104200 0x0501
> +
> #define MARATHON_PCI_DEVICE_ID 0x2715
>
> #define TEWS_PCI_VENDOR_ID 0x1498
> @@ -147,6 +163,30 @@ static struct plx_pci_card_info
> plx_pci_card_info_adlink_se __devinitdata = {
> /* based on PLX9052 */
> };
>
> +static struct plx_pci_card_info plx_pci_card_info_esd200 __devinitdata = {
> + "esd CAN-PCI/CPCI/PCI104/200", 2,
> + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
> + {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
> + &plx_pci_reset_common
> + /* based on PLX9030/9050 */
> +};
> +
> +static struct plx_pci_card_info plx_pci_card_info_esd266 __devinitdata = {
> + "esd CAN-PCI/PMC/266", 2,
> + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
> + {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
> + &plx_pci_reset_common
> + /* based on PLX9056 */
> +};
> +
> +static struct plx_pci_card_info plx_pci_card_info_esd2000 __devinitdata = {
> + "esd CAN-PCIe/2000", 2,
> + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
> + {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
> + &plx_pci_reset_common
> + /* based on PEX8311 */
> +};
> +
> static struct plx_pci_card_info plx_pci_card_info_marathon __devinitdata = {
> "Marathon CAN-bus-PCI", 2,
> PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
> @@ -179,6 +219,48 @@ static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) = {
> (kernel_ulong_t)&plx_pci_card_info_adlink_se
> },
> {
> + /* esd CAN-PCI/200 */
> + PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
> + PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI200,
> + 0, 0,
> + (kernel_ulong_t)&plx_pci_card_info_esd200
> + },
> + {
> + /* esd CAN-CPCI/200 */
> + PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
> + PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_CPCI200,
> + 0, 0,
> + (kernel_ulong_t)&plx_pci_card_info_esd200
> + },
> + {
> + /* esd CAN-PCI104/200 */
> + PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
> + PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI104200,
> + 0, 0,
> + (kernel_ulong_t)&plx_pci_card_info_esd200
> + },
> + {
> + /* esd CAN-PCI/266 */
> + PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
> + PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI266,
> + 0, 0,
> + (kernel_ulong_t)&plx_pci_card_info_esd266
> + },
> + {
> + /* esd CAN-PMC/266 */
> + PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
> + PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PMC266,
> + 0, 0,
> + (kernel_ulong_t)&plx_pci_card_info_esd266
> + },
> + {
> + /* esd CAN-PCIE/2000 */
> + PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
> + PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCIE2000,
> + 0, 0,
> + (kernel_ulong_t)&plx_pci_card_info_esd2000
> + },
> + {
> /* Marathon CAN-bus-PCI card */
> PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID,
> PCI_ANY_ID, PCI_ANY_ID,
> @@ -304,10 +386,13 @@ static void plx_pci_del_card(struct pci_dev *pdev)
> plx_pci_reset_common(pdev);
>
> /*
> - * Disable interrupts from PCI-card (PLX90xx) and disable Local_1,
> - * Local_2 interrupts
> + * Disable interrupts from PCI-card and disable local
> + * interrupts
> */
> - iowrite32(0x0, card->conf_addr + PLX_INTCSR);
> + if (pdev->device != PCI_DEVICE_ID_PLX_9056)
> + iowrite32(0x0, card->conf_addr + PLX_INTCSR);
> + else
> + iowrite32(0x0, card->conf_addr + PLX9056_INTCSR);
>
> if (card->conf_addr)
> pci_iounmap(pdev, card->conf_addr);
> @@ -437,10 +522,17 @@ static int __devinit plx_pci_add_card(struct pci_dev
> *pdev,
> * Enable interrupts from PCI-card (PLX90xx) and enable Local_1,
> * Local_2 interrupts from the SJA1000 chips
> */
> - val = ioread32(card->conf_addr + PLX_INTCSR);
> - val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
> - iowrite32(val, card->conf_addr + PLX_INTCSR);
> -
> + if (pdev->device != PCI_DEVICE_ID_PLX_9056) {
> + val = ioread32(card->conf_addr + PLX_INTCSR);
> + if (pdev->subsystem_vendor == PCI_VENDOR_ID_ESDGMBH)
> + val |= PLX_LINT1_EN | PLX_PCI_INT_EN;
> + else
> + val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
> + iowrite32(val, card->conf_addr + PLX_INTCSR);
> + } else {
> + iowrite32(PLX9056_LINTI | PLX9056_PCI_INT_EN,
> + card->conf_addr + PLX9056_INTCSR);
> + }
> return 0;
>
> failure_cleanup:
_______________________________________________
Socketcan-core mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/socketcan-core
