Hi Vim, thanks for your help, set ConSpeed did the trick! :-) I looked at the commands listed when you type ?, but never tried the "show" command..... Robin
> -----Original Message----- > From: Wim Vandeputte Mailing list only [mailto:[EMAIL PROTECTED] > Sent: Tuesday, October 14, 2008 10:20 PM > To: Robin Kipp > Cc: [email protected] > Subject: Re: [Soekris] How to set baudrate for serial interface? > > > > hey, > > On Tue, Oct 14, 2008 at 08:49:33PM +0200, Robin Kipp wrote: > > First thing I did is I upgraded it to Com Bios v1.33c and > now I want > > to install Debian on it. However, I have to change the baudrate to > > 9600 baud. In the bios, I tried the command set ComBaud = 9600, but > > that doesn't work :-( Can anyone please tell me the right command? > > Also, is there a list of all the commands you can issue to CB? > > Thanks!!! > > Just read what the boards tells you (read the net4801 manual > for more hints) > > [snip] > > comBIOS Monitor. Press ? for help. > > (see the hint? :-) > > > ? > comBIOS Monitor Commands > > boot [drive][:partition] INT19 Boot > reboot cold boot > download download a file using XMODEM/CRC > flashupdate update flash BIOS with downloaded file > time [HH:MM:SS] show or set time > date [YYYY/MM/DD] show or set date > d[b|w|d] [adr] dump memory bytes/words/dwords > e[b|w|d] adr value [...] enter bytes/words/dwords > i[b|w|d] port input from 8/16/32-bit port > o[b|w|d] port value output to 8/16/32-bit port > run adr execute code at adr > cmosread [adr] read CMOS RAM data > cmoswrite adr byte [...] write CMOS RAM data > cmoschecksum update CMOS RAM Checksum > set parameter=value set system parameter to value > show [parameter] show one or all system parameters > ?/help show this help > > > show > > ConSpeed = 19200 > ConLock = Enabled > ConMute = Disabled > BIOSentry = Enabled > PCIROMS = Enabled > PXEBoot = Enabled > FLASH = Primary > BootDelay = 5 > FastBoot = Disabled > BootPartition = Disabled > BootDrive = 80 81 F0 FF > ShowPCI = Enabled > Reset = Hard > CpuSpeed = Default > > > set ConSpeed 9600 > > > reboot > ææþx~þxx`xæàà`~~æxàxxxxxxxxxæxxàxxxøæøxxxxxxxxxxxxxxxxxxxxxxxx > xxxxxxxxxxxxxxxxxæfæx`fxæøfxxxxxæxàxxææææà~xxxxxææææææææææææææ > ææææææææææææææææææææææææææææææææææææææææææææææææææææææx~xàx~xx > àxxxxxxxxxxàxxàxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxàxxx~ > xx~xx~xx~xxàxàxxxxxæxxxxxxxxxøxxxàxàxxxxxxxxxxxxxxxxxxxxxxxxøx > x~xøx~xxàxàxxxxxæxxxxxxxxxøxxxàxàxxxxxxxxxxxxxxxxxxxxàxxxxxxxx > xàxxæx~xx~xxàxxxxxxxøxxxxxàxxxxxxxxxøxxxxxxxxxxxxxxxxxxxxàxxxx > xxxxàxxx~xx~xxàxxxxxxxøxxxàxxàxxxxàxxxxxæxxxxxxxxxxxxxxxxxxxxx > xxxxxxxxxxxxx~xàx~xxàxxxxxxxøxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxæx > xxxxxxxxxxxxxàxæxx~xàx~xxàx > _______________________________________________ Soekris-tech mailing list [email protected] http://lists.soekris.com/mailman/listinfo/soekris-tech
