Module Name: src Committed By: sborrill Date: Mon Nov 9 12:35:32 UTC 2015
Added Files: src/sys/dev/pci [netbsd-5]: if_bnxvar.h Log Message: Pull up the following revisions(s) (requested by msaitoh in ticket #1983): sys/dev/pci/pcidevs: revisions 1.1079, 1.1134, 1.1148-1.1149, 1.1151 sys/dev/pci/pcidevs.h: regen sys/dev/pci/pcidevs_data.h: regen sys/dev/pci/if_bge.c: revisions 1.183-1.185, 1.187, 1.189-1.193, 1.195-1.199, 1.202-1.226, 1.228-1.237, 1.240-1.264, 1.267-1.276, 1.278-1.280, 1.283-1.287 via patch sys/dev/pci/if_bgereg.h: revisions 1.57-1.74, 1.76-1.90 via patch sys/dev/pci/if_bgevar.h: revisions 1.6, 1.10-1.13, 1.15-1.17 via patch sys/dev/pci/if_bnx.c: revisions 1.32, 1.34-1.43, 1.48-1.49, 1.52 sys/dev/pci/if_bnxreg.h: revisions 1.8, 1.11-1.14 sys/dev/pci/if_bnxvar.h: revisions 1.1-1.3 sys/dev/mii/brgphy.c: revisions 1.53-1.63, 1.65-69, 1.72-1.74 via patch sys/dev/mii/brgphyreg.h: revisions 1.5-1.8 sys/dev/mii/miivar.h: revisions 1.61 sys/dev/pci/pcireg.h: patch Sync bge(4) up to if_bge.c rev. 1.287. Sync brgphy(4) up to 1.74. Fix some bugs on bnx(4). Common: - Add device IDs for Broadcom BCM57710, BCM57711(E), BCM57712(E) and BCM57766 (pcidevs only). - Fix BCM5709 PHY detection. - Fix detection of BGEPHYF_FIBER_{MII|TBI} - Add BCM5708S support in brgphy(4). - Don't use the WIRESPEED function for fiber devices. bge(4): - Add some Fujitsu's device support from Michael Moll. - Add BCM57762 support (PR#46961 from Ryo Onodera). - Add Altima AC1003, APPLE BCM5701, Broadcom BCM5785F. BCM5785G, BCM5787F, BCM5719, BCM5720, BCM57766, BCM57782 and BCM57786. - Fix DMA setting for read/write on conventional PCI bus devices. This bug was added in rev. 1.166. - Fix printing "discarding oversize frame (len=-4)" message and crash by NULL pointer dereferencing. - The BCM5785 is a PCIe chip but does not report PCIe capabilities. Check for this chip explicitely and enable PCIe. Fixes 'firmware handshake timeout'. - Allow disabling interrupt mitigation. - Workaround for BCM5906 silicon bug. When auto-negotiation results in half-duplex operation, excess collision on the ethernet link may cause internal chip delays that may result in subsequent valid frames being dropped due to insufficient receive buffer resources. (FreeBSD: r214219, r214251, r214292). - Allow write DMA to request larger DMA burst size to get better performance on BCM5785. (FreeBSD r213333: OpenBSD 1.294) - Enable TX MAC state machine lockup fix for both BCM5755 or higher and BCM5906. Publicly available data sheet just says it may happen due to corrupted TxMbuf. (FreeBSD r214216) - Follow Broadcom datasheet: Delay 100 microseconds after enabling transmit MAC. Delay 10 microseconds after enabling receive MAC. (FreeBSD r241220) - Insert the completion barrier between register write and the consecutive delay(). It will fix some device timeout problems we have seen before. - Add DELAY(40) after turning on write DMA state machine. - Add some workarounds for 5717 A0 and 5776[56] to be stable. - Check BGE_RXBDFLAG_IPV6 flag for 5717_PLUS case. Note that {tcp,udp}6csum flag is currently not added in the capability. - Add delay after clearing BGE_MACMODE_TBI_SEND_CFGS for the link checking. - Do not touch the jumbo replenish threshold register on chips that do not have jumbo support. - Wait for the bootcode to complete initialization for 5717 and newer devices. - 5718 and 57785 document say we should wait 100us in init. - Fix a bug that chips which have BCM5906 ASIC touch GPIO wrongly. - Fix the setting of Tx Random Backoff Register. - Check the hardware config words and print them. - Set BGE_MISC_CTL's byte/word swap options before using bge_readmem_ind(). Fixes PR#47716. - For BGE_IS_575X_PLUS() devices, don't set BGE_RXLPSTATCONTROL_DACK_FIX bits because these bits are reserved. - Document says 5717 and newer chips have no BGE_PCISTATE_INTR_NOT_ACTIVE bit, so don't use the bit on those chips. Same as OpenBSD. - Fix a bug that the PHY address bits in MI_MODE register is wrongly cleard. Set the PHY address correctly. - Use BGE_SETBIT() instead of CSR_WRITE_4() for the BGE_MISC_LOCAL_CTL register to not to modify some GPIO bits. - Set DMA watermark depend on the PCI max payload size. - Set BGE_JUMBO_CAPABLE correctly. - Fix a link detect bug on non-autopoll systems. - Change the TX ring size for 5717 series and 57764 series. - Set maximum read byte count to 2048 for PCI-X BCM5703/5704 devices. - For PCI-X BCM5704, set maximum outstanding split transactions to 0. - Add 40bit DMA bug workaround(BGEF_40BIT_BUG) from FreeBSD. This workaround is for 5714/5715 controllers and is not actually a MAC controller bug but an issue with the embedded PCIe to PCI-X bridge in the device. This change uses bus_dmatag_subregion(), so this workaround won't work on some archs which doesn't support bus_dmatag_subregion(). - Add 2500SX support (not tested). - Don't use the PHY Auto Poll Mode on many chips. This fixes a bug that MII Fiber NIC drop packet about 50%. Tested on HP Moonshot. - Add workaround for PR#48451. Some BCM5717-5720 based systems getNMI on boot. This problem doesn't occur when we don't use prefetchable memory in the APE area. Tested with HP MicroServer Gen8. - In the BCM5703, the DMA read watermark should be set to less than or equal to the maximum memory read byte count of the PCI-X command register. - Fix a bug that BGE_PHY_TEST_CTRL_REG isn't set correctly on some PCIe devices. - Use another firmware command in bge_asf_driver_up(). Same as Linux. This change fixes a bug that watchdog timeout occurs every 25-30 minutes on HP ML110 G6 reported enami@ in PR#49657. - Fix mbuf leak on failure. - Remove PCI_PRODUCT_BROADCOM_BCM5724 and PCI_PRODUCT_BROADCOM_BCM5750M. These devices have not released to public. - Add some workaround code for BGE_ASICREV_BCM5784 from Linux. - Change some printf() to aprint_*(). - Fix typo in comments. - Cleanup. brgphy(4): - Fix bit definition of BRGPHY_MRBE_MSG_PG5_NP_T2 from FreeBSD. - Add BCM5481, BCM5709S, BCM5756, BCM5717C, BCM5720C, BCM5785, BCM57765(PR#46961), BCM57780 - In brgphyattach(), set sc_isbge, sc_isbnx and sc_phyflags before PHY_RESET() because brgphy_reset() refers those flags. - Call brgpy specific autonego function in MII_TICK. Before this commit, only MII_MEDIACHG calls brgphy_mii_phy_auto() and MII_TICK calls MI mii_phy_auto(). That was not intended. - Remove extra delay in brgphy_mii_phy_auto. Same as {Free,Open}BSD. bnx(4): - Add missing ifmedia_delete_instance() in bnx_detach(). - Fix a bug that BNX_NO_WOL_FLAG isn't correctly set on some chips. Reported by From Henning Petersen in PR#44151. - Fix SERDES initialization. - Get out of the interrupt handler early if !IFF_RUNNING. To generate a diff of this commit: cvs rdiff -u -r0 -r1.6.8.2 src/sys/dev/pci/if_bnxvar.h Please note that diffs are not public domain; they are subject to the copyright notices on the relevant files.