Update on this issue. Have opened a case with support, to find out when this ios release will be supported.
________________________________ From: Bourlin, Stephen [mailto:[email protected]] Sent: Thursday, September 09, 2010 1:44 PM To: Murtey, Patrick Subject: RE: cisco ncm causes reboots Wow, that's good to know. You might want to put that out there for the group to know. Regards, Stephen B. DoIT NMS/NOC NOC Phone # 386-1995 Desk Phone # 733-9154 From: Murtey, Patrick [mailto:[email protected]] Sent: Thursday, September 09, 2010 12:31 PM To: Bourlin, Stephen Subject: RE: cisco ncm causes reboots We have completed some testing of our own and come to find that it is an IOS issue. NCM cant handle cisco IOS of 12.2.50 and Higher. I even tried the same device on my spectrum 9.2 h01 SpectroServer, and got the same results. I am hoping that the support will catch up in 92.sp1. ________________________________ From: Bourlin, Stephen [mailto:[email protected]] Sent: Thursday, September 09, 2010 12:02 PM To: Murtey, Patrick Subject: RE: cisco ncm causes reboots I don't know, both of these 3750's have plenty of free memory. One of them said last reset from power on and the other said last reset from address error. I would investigate that one. Are you managing the switches via SNMP ver1, ver2 or ver3? Can you send me the information for the 2960 and the 3560? Regards, Stephen B. DoIT NMS/NOC NOC Phone # 386-1995 Desk Phone # 733-9154 From: Murtey, Patrick [mailto:[email protected]] Sent: Wednesday, September 08, 2010 8:30 AM To: Bourlin, Stephen Subject: RE: cisco ncm causes reboots Attached ________________________________ From: Bourlin, Stephen [mailto:[email protected]] Sent: Tuesday, September 07, 2010 4:14 PM To: Murtey, Patrick Subject: RE: cisco ncm causes reboots Send me a "sh ver" and a "dir" from a 3560 and a "dir" and a "sh ver" and "dir all-filesystems" from a 3750 . I think it's a memory issue with them as well. I'm running Spectrum 9.2 and our IOS gold version isn't much new then yours. But I didn't have any issues when we were running Spectrum 9.1 and older IOS version. Regards, Stephen B. DoIT NMS/NOC NOC Phone # 386-1995 Desk Phone # 733-9154 From: Murtey, Patrick [mailto:[email protected]] Sent: Tuesday, September 07, 2010 3:46 PM To: Bourlin, Stephen Subject: RE: cisco ncm causes reboots Also a 3750 running 12.2.(44) an a 3560 running 12.2.35. both have a total non volatile Ram size 524288, 10442 used. ________________________________ From: Murtey, Patrick Sent: Tuesday, September 07, 2010 3:24 PM To: 'Bourlin, Stephen' Subject: RE: cisco ncm causes reboots The 2960's are running 12.2.37 IOS with 62914560kb of system cpu ram, 12366 of non-volatile ram used, 65536 non-volatile ram size. We are on Spectrum 9.1 sp1. ________________________________ From: Bourlin, Stephen [mailto:[email protected]] Sent: Tuesday, September 07, 2010 3:15 PM To: Murtey, Patrick Subject: RE: cisco ncm causes reboots What IOS version are you guys running and what's your memory on them. We run 2960's and we've never had that problem. Also what version of Spectrum are you running? Regards, Stephen B. DoIT NMS/NOC NOC Phone # 386-1995 Desk Phone # 733-9154 From: Murtey, Patrick [mailto:[email protected]] Sent: Tuesday, September 07, 2010 3:13 PM To: Bourlin, Stephen Subject: RE: cisco ncm causes reboots We know for sure it is happening on the 2960 switch. ________________________________ From: Bourlin, Stephen [mailto:[email protected]] Sent: Tuesday, September 07, 2010 2:54 PM To: Murtey, Patrick Subject: RE: cisco ncm causes reboots What type of Cisco device and how much memory does it have. We had an issue with older Cisco 2924's and 2950's with low memory would experience high CPU utilization to the point they would be unreachable and locked up. They would still pass data, but we would have to reboot them to regain access to them, but no I've never seen a Cisco device reload after a NCM push. Regards, Stephen B. DoIT NMS/NOC NOC Phone # 386-1995 Desk Phone # 733-9154 From: Murtey, Patrick [mailto:[email protected]] Sent: Tuesday, September 07, 2010 12:59 PM To: spectrum Subject: [spectrum] cisco ncm causes reboots Hi All, We have noticed when using NCM on some Cisco Devices, when you tftp push the config back to the devices with changes and select "also save to startup". It will cause the switch/router to reboot itself. Is this normal behavior? Is there a way to allow the write to startup, without the reboot occurring? TIA Patrick Murtey MGM RESORTS Information Technology [email protected] * --To unsubscribe from spectrum, send email to [email protected] with the body: unsubscribe spectrum [email protected] --- To unsubscribe from spectrum, send email to [email protected] with the body: unsubscribe spectrum [email protected]
<<image001.jpg>>
<<attachment: Stephen Bourlin5.vcf>>
