according to the ./configure output pthread.lib isn't yet supported ( I guess this is only true for OpenBSD ) so pppoa3 doesn't get build by make so I can only use pppoa2. Should work though because if I look through the mailing archives I can see that many people are using the speedtouch drivers with OpenBSD 3.2...
Juel On Fri, 24 Jan 2003 11:07:36 +0100, Vaessen, E.M.J. (Ed) <[EMAIL PROTECTED]> wrote: > I only know something about how to configure the speedtouch USB (330) > modem > on (Mandrake) linux. > I was surprised to see that you use pppoa2 and not pppoa3. > > Ed > > >> -----Oorspronkelijk bericht----- >> Van: Juel da Costa [mailto:[EMAIL PROTECTED]] >> Verzonden: donderdag 23 januari 2003 18:45 >> Aan: [EMAIL PROTECTED] >> Onderwerp: [speedtouch] errno: No such process on OpenBSD 3.2 >> >> >> >> Hi all, >> >> I am hoping anyone can help me with the following problem: >> >> Having just installed a clean OpenBSD 3.2 system (on a laptop) I have >> built and installed speedtouch-1.1.tar.gz and copied mgmt.o the /usr/local/libdata/ >> . I have copied the sample ppp.conf file to /etc/ppp/ppp.conf and >> amended it to fit my own requirements and changed /etc/syslog.conf to >> enable modem_run and pppoa2 to log to /var/log/messages. >> >> When I start modem_run it all seems to work fine according to the log entries >> in /var/log/messages but when I start "ppp adsl" I'm getting the following >> error messages : >> >> Jan 23 14:56:15 omni ppp[27087]: tun0: Warning: Add route failed: 0.0.0.0/0: >> errno: No such process >> >> and then I'm dropped into ppp interactive mode. >> When I open another console I can see that tun0 hasn't been configured. >> >> I doublechecked that I specified the full path to pppoa2 in ppp.conf and >> I even tried explicitly specifying -d /dev/ugen0 but that didn't work >> either. >> >> Does anyone have any ideas on how to solve this? Any suggestions would >> be welcome because I'm getting desperate... >> >> Thanks, >> Juel >> >> my ppp.conf >> >> default: >> ident user-ppp VERSION (built COMPILATIONDATE) >> set log Phase Chat IPCP CCP tun command >> >> adsl: >> set authname myusername >> set authkey mypassword >> set device !"/usr/local/sbin/pppoa2 -d /dev/ugen0 -vpi 8 -vci 48 -v 2" >> accept chap >> set speed sync >> set timeout 0 >> enable lqr >> set lqrperiod 5 >> set redial 15 10000 >> set dial "" >> set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 >> add default HISADDR >> enable dns >> >> >> >> Liste de diffusion modem ALCATEL SpeedTouch USB >> Pour se désinscrire : mailto:speedtouch- >> [EMAIL PROTECTED]?subject=unsubscribe >> >> >> > > Disclaimer > ************************************************************************ > Aan dit bericht kunnen geen rechten worden ontleend. Dit bericht is > uitsluitend bestemd voor de geadresseerde. > Als u dit bericht per abuis hebt ontvangen, wordt u verzocht het te vernietigen > en de afzender te informeren. > Wij adviseren u om bij twijfel over de juistheid of de volledigheid van de > mail contact met afzender op te nemen. > ************************************************************************ > > > > Liste de diffusion modem ALCATEL SpeedTouch USB > Pour se désinscrire : mailto:speedtouch- > [EMAIL PROTECTED]?subject=unsubscribe > > > -- Juel da Costa Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]?subject=unsubscribe
