I had these CRC errors too on a GA-7VAXP mother board that uses the VIA chipset. I got myself a USB/PCI card with a OPTi chipset. Error free now!
> -----Oorspronkelijk bericht----- > Van: Jose Bernardo Silva [mailto:[EMAIL PROTECTED] > Verzonden: zondag 23 februari 2003 16:20 > Aan: speedtouch mailing > Onderwerp: [speedtouch] CRC error in an AAL5 frame > > > > Well, now I have my speedtouch 330 working with Mandrake's > MNF 8.2, I get "CRC > error in an AAL5 frame" by the dozen, and the transfer speeds > are around > 25Kbps. My hardware is a AMD K6-3D+ running at 450Mhz, my > motherboard has a > VIA chipset (usb-ohci), and a lspci -v gives the following output: > > lspci -v > 00:00.0 Host bridge: Acer Laboratories Inc. [ALi] M1541 (rev 04) > Subsystem: Acer Laboratories Inc. [ALi] ALI M1541 > Aladdin V/V+ AGP > System Controller > Flags: bus master, slow devsel, latency 64 > Memory at e0000000 (32-bit, non-prefetchable) [size=64M] > Capabilities: [b0] AGP version 1.0 > > 00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5243 (rev > 04) (prog-if 00 > [Normal decode]) > Flags: bus master, slow devsel, latency 64 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > > 00:02.0 USB Controller: Acer Laboratories Inc. [ALi] M5237 > USB (rev 03) > (prog-if 10 [OHCI]) > Flags: bus master, medium devsel, latency 64, IRQ 9 > Memory at df800000 (32-bit, non-prefetchable) [size=4K] > > 00:03.0 Bridge: Acer Laboratories Inc. [ALi] M7101 PMU > Subsystem: Acer Laboratories Inc. [ALi] ALI M7101 > Power Management > Controller > Flags: medium devsel > > 00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to > ISA Bridge > [Aladdin IV] (rev c3) > Flags: bus master, medium devsel, latency 0 > > 00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL-8139 (rev 10) > Subsystem: OVISLINK Corp. LFE-8139ATX > Flags: bus master, medium devsel, latency 32, IRQ 12 > I/O ports at d800 [size=256] > Memory at df000000 (32-bit, non-prefetchable) [size=256] > Expansion ROM at <unassigned> [disabled] [size=64K] > Capabilities: [50] Power Management version 2 > > 00:0a.0 Ethernet controller: 3Com Corporation 3c905B > 100BaseTX [Cyclone] (rev 30) > Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100 > Flags: bus master, medium devsel, latency 32, IRQ 5 > I/O ports at d400 [size=128] > Memory at de800000 (32-bit, non-prefetchable) [size=128] > Expansion ROM at <unassigned> [disabled] [size=128K] > Capabilities: [dc] Power Management version 1 > > 00:0b.0 SCSI storage controller: Adaptec AHA-2940U2/W > Subsystem: Adaptec: Unknown device a180 > Flags: bus master, medium devsel, latency 32, IRQ 10 > BIST result: 00 > I/O ports at d000 [disabled] [size=256] > Memory at de000000 (64-bit, non-prefetchable) [size=4K] > Expansion ROM at <unassigned> [disabled] [size=128K] > Capabilities: [dc] Power Management version 1 > > 00:0c.0 VGA compatible controller: Avance Logic Inc. > ALG-2064i (prog-if 00 [VGA]) > Flags: medium devsel, IRQ 11 > Memory at dd800000 (32-bit, non-prefetchable) [size=2M] > Expansion ROM at 000c0000 [disabled] [size=32K] > > 00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL-8139 (rev 10) > Subsystem: Realtek Semiconductor Co., Ltd. RT8139 > Flags: bus master, medium devsel, latency 32, IRQ 12 > I/O ports at b800 [size=256] > Memory at dd000000 (32-bit, non-prefetchable) [size=256] > Expansion ROM at <unassigned> [disabled] [size=64K] > > 00:0f.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c1) > (prog-if 8a [Master SecP PriP]) > Flags: bus master, medium devsel, latency 32 > [virtual] I/O ports at 01f0 > [virtual] I/O ports at 03f4 > [virtual] I/O ports at 0170 > [virtual] I/O ports at 0374 > I/O ports at b400 [size=16] > > Any ideas on what can I do to fix the CRC errors? > Thanks! > > > --- > Jose Bernardo B R Silva | Source Mage GNU/Linux Developer > [EMAIL PROTECTED] | http://www.sourcemage.org > http://counter.li.org #245602 > [EMAIL PROTECTED] > > > > Liste de diffusion modem ALCATEL SpeedTouch USB > Pour se désinscrire : > mailto:[EMAIL PROTECTED] > > > Disclaimer ************************************************************************ Aan dit bericht kunnen geen rechten worden ontleend. Dit bericht is uitsluitend bestemd voor de geadresseerde. Als u dit bericht per abuis hebt ontvangen, wordt u verzocht het te vernietigen en de afzender te informeren. Wij adviseren u om bij twijfel over de juistheid of de volledigheid van de mail contact met afzender op te nemen. ************************************************************************ Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
