I'm sorry for creating too many threads. I can't seem to reply to anything. I'm trying
the user-level drivers once again. Once again they seem to work up to point then just
fail. This time I made a log to show what is going on.
Here are the commands which I typed and the response:
[EMAIL PROTECTED]:~$ su
[EMAIL PROTECTED]:/home/avatar# modprobe ppp_generic
[EMAIL PROTECTED]:/home/avatar# modprobe ppp_synctty
[EMAIL PROTECTED]:/home/avatar# modprobe n_hdlc
[EMAIL PROTECTED]:/home/avatar# modprobe usbcore
[EMAIL PROTECTED]:/home/avatar# mount none /proc/bus/usb -t usbdevfs
[EMAIL PROTECTED]:/home/avatar# modprobe uhci
[EMAIL PROTECTED]:/home/avatar# modem_run -v 1 -m -f /usr/speedtouch/alcaudsl.sys
[EMAIL PROTECTED]:/home/avatar# pppd call adsl
[EMAIL PROTECTED]:/home/avatar# ifconfig ppp0
ppp0 Link encap:Point-to-Point Protocol
POINTOPOINT NOARP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Here is what "/var/log/messages" shows me:
Feb 3 20:11:40 avatar kernel: CSLIP: code copyright 1989 Regents of the University of
California
Feb 3 20:11:40 avatar kernel: PPP generic driver version 2.4.2
Feb 3 20:11:49 avatar kernel: N_HDLC line discipline registered.
Feb 3 20:12:19 avatar modem_run[1298]: modem_run version 1.2-beta3 started by avatar
uid 0
Feb 3 20:12:19 avatar modem_run[1298]: Found ALCATEL SpeedTouch USB modem
Feb 3 20:12:19 avatar modem_run[1298]: Best offset 2772 with probability 100%
Feb 3 20:12:19 avatar modem_run[1298]: Best offset 671657 with probability 100%
Feb 3 20:12:19 avatar modem_run[1298]: Firmware information (CRC:0xe0251a5e,
Size:671665, 1.6.1 - Win32(5.0.1801))
Feb 3 20:12:21 avatar modem_run[1298]: BLOCK1 : 883 bytes uploaded : OK
Feb 3 20:12:22 avatar modem_run[1298]: BLOCK2 : 511 bytes downloaded : OK
Feb 3 20:12:24 avatar modem_run[1298]: BLOCK3 : 671665 bytes uploaded : OK
Feb 3 20:12:24 avatar modem_run[1298]: BLOCK4 : 511 bytes downloaded : OK
Feb 3 20:12:25 avatar modem_run[1298]: Modem reference : 3EC18607USAB01
Feb 3 20:12:39 avatar modem_run[1299]: Sending a signal to notify the adsl up state
Feb 3 20:12:39 avatar modem_run[1298]: ADSL synchronization has been obtained
Feb 3 20:12:39 avatar modem_run[1298]: ADSL line is up (160 kbit/s down | 96 kbit/s up)
Feb 3 20:12:43 avatar pppd[1302]: pppd 2.4.1 started by root, uid 0
Feb 3 20:12:43 avatar pppd[1302]: Using interface ppp0
Feb 3 20:12:43 avatar pppd[1302]: Connect: ppp0 <--> /dev/pts/4
Feb 3 20:12:43 avatar pppoa3[1303]: pppoa3 version 1.2-beta3 started by root (uid 0)
Feb 3 20:12:43 avatar pppoa3[1303]: Vpi set to 0
Feb 3 20:12:43 avatar pppoa3[1303]: Vci set to 35
Feb 3 20:12:43 avatar pppoa3[1303]: Verbosity level set to 2
Feb 3 20:12:43 avatar pppoa3[1303]: Schedule policy set to 0
Feb 3 20:12:43 avatar pppoa3[1303]: Modem ID set to 1
Feb 3 20:12:43 avatar pppoa3[1303]: Using Sync HDLC mode
Feb 3 20:12:43 avatar pppoa3[1303]: Using PPPoA mode
Feb 3 20:12:43 avatar pppoa3[1303]: Control pipe disabled
Feb 3 20:12:43 avatar pppoa3[1303]: Previous instance cleaning enabled
Feb 3 20:12:43 avatar pppoa3[1303]: Control thread ready
Feb 3 20:12:43 avatar pppoa3[1303]: Modem found!
Feb 3 20:12:43 avatar pppoa3[1312]: host --> pppoa3 --> modem stream ready
Feb 3 20:12:43 avatar pppoa3[1313]: modem --> pppoa3 --> host stream ready
Feb 3 20:13:14 avatar pppd[1302]: Connection terminated.
Feb 3 20:13:14 avatar pppoa3[1312]: Cleaning Read from usb data
Feb 3 20:13:14 avatar pppoa3[1303]: Write to usb Canceled
Feb 3 20:13:14 avatar pppoa3[1313]: Cleaning Write to usb data
And finally this is what "/var/log/syslog" tells me:
Feb 3 20:11:49 avatar kernel: HDLC line discipline: version $Revision: 3.3 $,
maxframe=4096
Feb 3 20:12:21 avatar kernel: usb_control/bulk_msg: timeout
Feb 3 20:12:21 avatar kernel: usbdevfs: USBDEVFS_BULK failed dev 6 ep 0x85 len 512 ret
-110
Feb 3 20:13:14 avatar pppd[1302]: LCP: timeout sending Config-Requests
Feb 3 20:13:14 avatar pppoa3[1312]: Error reading from source device
Feb 3 20:13:14 avatar pppoa3[1303]: Woken by a sem_post event -> Exiting
Any help whatsoever would be appreciated. So far, from what I gather, the firmware
upload works. All the modules are present. The only thing I see that goes wrong is
once I type "pppd call adsl". It works all according to plan....then finds a previous
instance (????) and fails for no reason. Can someone explain this? I really would love
to get this working, I've spent far too much time trying this and I am running out of
plans.
Bewildred: avatar_58
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se d�sinscrire : mailto:[EMAIL PROTECTED]
