SPI master controller driver for the Intel MID platform Medfield
This driver uses the Penwell SSP controller and configures it to
be a SPI device (spibus 3). This bus supports a single device -
the 3G SPI modem that can operate up to 25Mhz.
Signed-off-by: Russ Gorby <russ.go...@intel.com>
---
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/intel_mid_ssp_spi.c | 1507 +++++++++++++++++++++++++++++++++++
drivers/spi/intel_mid_ssp_spi_def.h | 139 ++++
4 files changed, 1654 insertions(+), 0 deletions(-)
create mode 100644 drivers/spi/intel_mid_ssp_spi.c
create mode 100644 drivers/spi/intel_mid_ssp_spi_def.h
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index bb233a9..60ba339 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -178,6 +178,13 @@ config SPI_IMX
This enables using the Freescale i.MX SPI controllers in master
mode.
+config SPI_INTEL_MID_SSP
+ tristate "SSP SPI controller driver for Intel Medfield platform"
+ depends on SPI_MASTER && INTEL_MID_DMAC
+ help
+ This is the SPI master controller driver for the Intel
+ Medfield MID platform.
+
config SPI_LM70_LLP
tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
depends on PARPORT && EXPERIMENTAL
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 86d1b5f..c64deb9 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
obj-$(CONFIG_SPI_SH_MSIOF) += spi_sh_msiof.o
obj-$(CONFIG_SPI_STMP3XXX) += spi_stmp.o
obj-$(CONFIG_SPI_NUC900) += spi_nuc900.o
+obj-$(CONFIG_SPI_INTEL_MID_SSP) += intel_mid_ssp_spi.o
# special build for s3c24xx spi driver with fiq support
spi_s3c24xx_hw-y := spi_s3c24xx.o
diff --git a/drivers/spi/intel_mid_ssp_spi.c b/drivers/spi/intel_mid_ssp_spi.c
new file mode 100644
index 0000000..19c62bc
--- /dev/null
+++ b/drivers/spi/intel_mid_ssp_spi.c
@@ -0,0 +1,1507 @@
+/*
+ * intel_mid_ssp_spi.c - Penwell SPI master controller driver
+ * based on pxa2xx.c
+ *
+ * Copyright (C) Intel 2010
+ * Ken Mills <ken.k.mi...@intel.com>
+ * Russ Gorby <russ.go...@intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
+ * USA
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/highmem.h>
+#include <linux/pci.h>
+#include <linux/dma-mapping.h>
+#include <linux/pm_qos_params.h>
+#include <linux/intel_mid_dma.h>
+#include <linux/interrupt.h>
+#include <linux/spi/spi.h>
+#include <linux/pm_runtime.h>
+#include "intel_mid_ssp_spi_def.h"
+
+#define DRIVER_NAME "intel_mid_ssp_spi"
+#define PCI_DMAC_MAXDI 2047
+#define PCI_DMAC_ID 0x0827
+/* PM QoS define */
+#define MIN_EXIT_LATENCY 20
+
+#define TESTMODE_COMMON_MASK 0x00ff
+#define TESTMODE_PRIV_MASK 0xff00
+#define TESTMODE_ENABLE_DMA 0x01
+#define TESTMODE_ENABLE_POLL 0x02
+#define TESTMODE_ENABLE_LOOPBACK 0x04
+#define TESTMODE_ENABLE_INTR 0x08
+#define TESTMODE(x) (testmode & x)
+static unsigned int testmode = (TESTMODE_ENABLE_DMA | TESTMODE_ENABLE_POLL);
+
+module_param(testmode, uint, S_IRUGO|S_IWUSR);
+MODULE_PARM_DESC(testmode, "supply test mode bits");
+
+MODULE_AUTHOR("Intel");
+MODULE_DESCRIPTION("Penwell SPI3 Master Contoller");
+MODULE_LICENSE("GPL");
+
+#define RX_THRESH_DFLT 8
+#define TX_THRESH_DFLT 8
+#define TIMOUT_DFLT 1000
+
+/*
+ * For testing SSCR1 changes that require SSP restart, basically
+ * everything except the service and interrupt enables
+ */
+
+#define SSCR1_CHANGE_MASK (SSCR1_TTELP | SSCR1_TTE | SSCR1_SCFR \
+ | SSCR1_ECRA | SSCR1_ECRB | SSCR1_SCLKDIR \
+ | SSCR1_SFRMDIR | SSCR1_RWOT | SSCR1_TRAIL \
+ | SSCR1_IFS | SSCR1_STRF | SSCR1_EFWR \
+ | SSCR1_RFT | SSCR1_TFT | SSCR1_MWDS \
+ | SSCR1_SPH | SSCR1_SPO | SSCR1_LBM)
+
+#define PNWL_SSPSP (SSPSP_FSRT | SSPSP_SFRMWDTH(1) | SSPSP_SFRMP | \
+ SSPSP_SCMODE(3))
+
+/*
+ * clock divider
+ * 8 bpw
+ * TUR/ROR do not generate interrupt
+ * SPI mode operation
+ * SSP enabled
+ */
+#define PNWL_CR0(clk, bits, spi, chip) \
+ ((SSCR0_SerClkDiv(clk) & SSCR0_SCR) | \
+ SSCR0_Motorola | \
+ SSCR0_DataSize(bits > 16 ? bits - 16 : bits) | \
+ SSCR0_SSE | \
+ SSCR0_TIM | \
+ SSCR0_RIM | \
+ (bits > 16 ? SSCR0_EDSS : 0))
+
+#define PNWL_CR1_MASTER_ROLE 0
+#define PNWL_CR1_SLAVE_ROLE (SSCR1_SFRMDIR | SSCR1_SCLKDIR)
+/* MRST SSP must be slave */
+#define PNWL_CR1_ROLE PNWL_CR1_MASTER_ROLE
+#define PNWL_CR1(spi, chip) \
+ ((chip->enable_loopback ? SSCR1_LBM : 0) | \
+ ((spi->mode & SPI_CPHA) ? SSCR1_SPH : 0) | \
+ ((spi->mode & SPI_CPOL) ? SSCR1_SPO : 0) | \
+ SSCR1_SCFR | \
+ chip->threshold | \
+ PNWL_CR1_ROLE)
+
+
+
+struct callback_param {
+ void *drv_data;
+ int *donep;
+};
+
+enum dd_pwrstate {
+ PWRSTATE_ON = 1,
+ PWRSTATE_IDLE,
+ PWRSTATE_OFF,
+};
+
+enum dd_pwrflags {
+ PWRFLAG_RTRESUMING,
+};
+
+struct driver_data {
+ /* Driver model hookup */
+ struct pci_dev *pdev;
+ /* SPI framework hookup */
+ struct spi_master *master;
+
+ /* SSP register addresses */
+ unsigned long paddr;
+ void __iomem *ioaddr;
+ u32 iolen;
+ int irq;
+
+ /* SSP masks*/
+ u32 dma_cr1;
+ u32 int_cr1;
+ u32 clear_sr;
+ u32 mask_sr;
+
+
+ /* Current message transfer state info */
+ struct tasklet_struct poll_transfer;
+ struct spi_message *cur_msg;
+ size_t len;
+ void *tx;
+ void *tx_end;
+ void *rx;
+ void *rx_end;
+ int dma_mapped;
+ dma_addr_t rx_dma;
+ dma_addr_t tx_dma;
+ size_t rx_map_len;
+ size_t tx_map_len;
+ u8 n_bytes;
+ int (*write)(struct driver_data *drv_data);
+ int (*read)(struct driver_data *drv_data);
+ irqreturn_t (*transfer_handler)(struct driver_data *drv_data);
+ void (*cs_control)(u32 command);
+ struct workqueue_struct *wq;
+ struct work_struct resume_transfer_work;
+
+ /* controller state */
+ int dma_inited;
+
+ /* pwrstate mgmt */
+ int pwrstate; /* enum dd_pwrstate */
+ unsigned long pwrflags; /* enum dd_pwrflags */
+
+ /* used by DMA code */
+ struct pci_dev *dmac1;
+ struct intel_mid_dma_slave dmas_tx;
+ struct intel_mid_dma_slave dmas_rx;
+ struct dma_chan *txchan;
+ struct dma_chan *rxchan;
+ int txdma_done;
+ int rxdma_done;
+ struct callback_param tx_param;
+ struct callback_param rx_param;
+};
+
+struct chip_data {
+ u32 cr0;
+ u32 cr1;
+ u32 psp;
+ u32 timeout;
+ u8 n_bytes;
+ u32 threshold;
+ u8 enable_dma; /* use dma if possible */
+ u8 poll_mode; /* use poll mode */
+ u8 enable_loopback; /* configure in loopback mode */
+ u8 bits_per_word;
+ u32 speed_hz;
+ int (*write)(struct driver_data *drv_data);
+ int (*read)(struct driver_data *drv_data);
+};
+
+static int transfer(struct spi_device *, struct spi_message *);
+
+static inline int have_fifo_data(struct driver_data *drv_data, u32 *sssrp)
+{
+ u32 sssr;
+ void *reg = drv_data->ioaddr;
+ sssr = ioread32(reg + SSSR);
+
+ if (sssrp)
+ *sssrp = sssr;
+ return ((sssr & SSSR_TFL) || !(sssr & SSSR_TNF)) ||
+ ((sssr & SSSR_RFL) != SSSR_RFL || (sssr & SSSR_RNE));
+}
+
+static void flush(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ u32 sssr;
+
+ /* If the transmit fifo is not empty, reset the interface. */
+ if (have_fifo_data(drv_data, &sssr)) {
+ dev_warn(&drv_data->pdev->dev,
+ "ERROR: flush: fifos not empty! sssr:%x", sssr);
+ iowrite32(ioread32(reg + SSCR0) & ~SSCR0_SSE, reg + SSCR0);
+ return;
+ }
+
+ iowrite32(SSSR_ROR, reg + SSSR);
+ iowrite32(SSSR_TUR, reg + SSSR);
+}
+
+/*
+ * reader/writer functions
+ *
+ * *_reader functions return:
+ * 0: not complete (data not available)
+ * 1: *all* requested data has been read
+ *
+ * *_writer functions return:
+ * 1: data successfully writen
+ * 0: *all* requested data already written *or* full condition hit
+ * note: this means caller must verify write-complete condition
+ *
+ */
+static int null_writer(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ u8 n_bytes = drv_data->n_bytes;
+ if (((ioread32(reg + SSSR) & SSSR_TFL) == SSSR_TFL)
+ || (drv_data->tx == drv_data->tx_end))
+ return 0;
+
+ iowrite32(0, reg + SSDR);
+ drv_data->tx += n_bytes;
+
+ return 1;
+}
+
+static int null_reader(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ u8 n_bytes = drv_data->n_bytes;
+
+ while ((ioread32(reg + SSSR) & SSSR_RNE) &&
+ (drv_data->rx < drv_data->rx_end)) {
+
+ ioread32(reg + SSDR);
+ drv_data->rx += n_bytes;
+ }
+
+ return drv_data->rx == drv_data->rx_end;
+}
+
+static int u8_writer(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+
+ if (((ioread32(reg + SSSR) & SSSR_TFL) == SSSR_TFL)
+ || (drv_data->tx == drv_data->tx_end))
+ return 0;
+
+ iowrite32(*(u8 *)(drv_data->tx), reg + SSDR);
+ dev_dbg(&drv_data->pdev->dev, "u8_write: %x", ((u8 *)drv_data->tx)[0]);
+ drv_data->tx++;
+
+ return 1;
+}
+
+static int u8_reader(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+
+ while ((ioread32(reg + SSSR) & SSSR_RNE)
+ && (drv_data->rx < drv_data->rx_end)) {
+
+ *(u8 *)(drv_data->rx) = ioread32(reg + SSDR);
+ drv_data->rx++;
+ }
+
+ return drv_data->rx == drv_data->rx_end;
+}
+
+static int u16_writer(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ if (((ioread32(reg + SSSR) & SSSR_TFL) == SSSR_TFL)
+ || (drv_data->tx == drv_data->tx_end))
+ return 0;
+
+ iowrite32(*(u16 *)(drv_data->tx), reg + SSDR);
+ drv_data->tx += 2;
+
+ return 1;
+}
+
+static int u16_reader(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ dev_dbg(&drv_data->pdev->dev, "u16_read");
+
+ while ((ioread32(reg + SSSR) & SSSR_RNE)
+ && (drv_data->rx < drv_data->rx_end)) {
+
+ *(u16 *)(drv_data->rx) = ioread32(reg + SSDR);
+ drv_data->rx += 2;
+ }
+
+ return drv_data->rx == drv_data->rx_end;
+}
+
+static int u32_writer(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ dev_dbg(&drv_data->pdev->dev, "u32_write");
+
+ if (((ioread32(reg + SSSR) & SSSR_TFL) == SSSR_TFL)
+ || (drv_data->tx == drv_data->tx_end)) {
+ return 0;
+ }
+
+ iowrite32(*(u32 *)(drv_data->tx), reg + SSDR);
+ drv_data->tx += 4;
+
+ return 1;
+}
+
+static int u32_reader(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+
+ while ((ioread32(reg + SSSR) & SSSR_RNE)
+ && (drv_data->rx < drv_data->rx_end)) {
+
+ *(u32 *)(drv_data->rx) = ioread32(reg + SSDR);
+ drv_data->rx += 4;
+ }
+
+ return drv_data->rx == drv_data->rx_end;
+}
+
+
+/* caller already set message->status; dma and pio irqs are blocked */
+static void giveback(struct driver_data *drv_data)
+{
+ struct spi_message *msg;
+
+ msg = drv_data->cur_msg;
+ drv_data->cur_msg = NULL;
+ msg->state = NULL;
+ if (msg->complete)
+ msg->complete(msg->context);
+}
+
+static bool chan_filter(struct dma_chan *chan, void *param)
+{
+ struct driver_data *drv_data = (struct driver_data *)param;
+ bool ret = false;
+
+ if (!drv_data->dmac1)
+ return ret;
+
+ if (chan->device->dev == &drv_data->dmac1->dev)
+ ret = true;
+
+ return ret;
+}
+
+/**
+ * unmap_dma_buffers() - Unmap the DMA buffers used during the last transfer.
+ * @drv_data: Pointer to the private driver data
+ */
+static void unmap_dma_buffers(struct driver_data *drv_data,
+ struct spi_message *msg)
+{
+ struct device *dev = &drv_data->pdev->dev;
+
+ if (unlikely(!drv_data->dma_mapped)) {
+ dev_err(dev, "ERROR : DMA buffers not mapped");
+ return;
+ }
+ if (unlikely(msg->is_dma_mapped))
+ return;
+
+ dma_unmap_single(dev, drv_data->rx_dma, drv_data->len, DMA_FROM_DEVICE);
+ dma_unmap_single(dev, drv_data->tx_dma, drv_data->len, DMA_TO_DEVICE);
+ drv_data->dma_mapped = 0;
+}
+
+
+static void dma_transfer_complete(void *arg)
+{
+ struct callback_param *param = arg;
+ struct driver_data *drv_data = (struct driver_data *)param->drv_data;
+ int *done;
+ void *reg;
+ u32 sscr1;
+
+ done = (int *)param->donep;
+ reg = drv_data->ioaddr;
+ *done = 1;
+
+ if (!drv_data->txdma_done || !drv_data->rxdma_done)
+ return;
+
+ /* Clear Status Register */
+ iowrite32(drv_data->clear_sr, reg + SSSR);
+
+ sscr1 = ioread32(reg + SSCR1);
+
+ /* Disable Triggers to DMA */
+ sscr1 &= ~drv_data->dma_cr1;
+
+ /* Disable Interrupt */
+ sscr1 &= ~drv_data->int_cr1;
+ iowrite32(sscr1, reg + SSCR1);
+
+ /* Stop getting Time Outs */
+ iowrite32(0, reg + SSTO);
+
+ /* release DMA mappings */
+ unmap_dma_buffers(drv_data, drv_data->cur_msg);
+
+ /* Update total byte transfered return count actual bytes read */
+ drv_data->cur_msg->actual_length = drv_data->len;
+
+ drv_data->cur_msg->status = 0;
+ giveback(drv_data);
+ pm_runtime_put(&drv_data->pdev->dev);
+}
+
+/**
+ * intel_mid_ssp_spi_dma_init() - Initialize DMA
+ * @drv_data: Pointer to the private driver data
+ *
+ * This function is called at driver setup phase to allocate DMA
+ * ressources.
+ */
+static void intel_mid_ssp_spi_dma_init(struct driver_data *drv_data)
+{
+ struct intel_mid_dma_slave *rxs, *txs;
+ dma_cap_mask_t mask;
+
+ if (drv_data->dma_inited)
+ return;
+
+ drv_data->dmac1 = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DMAC_ID,
+ NULL);
+ if (!drv_data->dmac1) {
+ dev_warn(&drv_data->pdev->dev, "Can't find DMAC %x",
+ PCI_DMAC_ID);
+ return;
+ }
+
+ /* 1. init rx channel */
+ rxs = &drv_data->dmas_rx;
+ rxs->hs_mode = LNW_DMA_HW_HS;
+ rxs->cfg_mode = LNW_DMA_PER_TO_MEM;
+ rxs->dma_slave.direction = DMA_FROM_DEVICE;
+ rxs->dma_slave.src_maxburst = LNW_DMA_MSIZE_8;
+ rxs->dma_slave.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ rxs->dma_slave.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_MEMCPY, mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ drv_data->rxchan = dma_request_channel(mask, chan_filter, drv_data);
+ if (!drv_data->rxchan)
+ goto err_exit;
+ drv_data->rxchan->private = rxs;
+
+ /* 2. init tx channel */
+ txs = &drv_data->dmas_tx;
+ txs->hs_mode = LNW_DMA_HW_HS;
+ txs->cfg_mode = LNW_DMA_MEM_TO_PER;
+ txs->dma_slave.direction = DMA_TO_DEVICE;
+ txs->dma_slave.dst_maxburst = LNW_DMA_MSIZE_8;
+ txs->dma_slave.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ txs->dma_slave.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+
+ dma_cap_set(DMA_SLAVE, mask);
+ dma_cap_set(DMA_MEMCPY, mask);
+
+ drv_data->txchan = dma_request_channel(mask, chan_filter, drv_data);
+ if (!drv_data->txchan)
+ goto free_rxchan;
+ drv_data->txchan->private = txs;
+
+ drv_data->dma_inited = 1;
+ drv_data->txdma_done = 1;
+ drv_data->rxdma_done = 1;
+
+ drv_data->tx_param.drv_data = (void *)drv_data;
+ drv_data->tx_param.donep = &drv_data->txdma_done;
+ drv_data->rx_param.drv_data = (void *)drv_data;
+ drv_data->rx_param.donep = &drv_data->rxdma_done;
+ return;
+
+free_rxchan:
+ dev_err(&drv_data->pdev->dev, "DMA TX Channel Not available");
+ dma_release_channel(drv_data->rxchan);
+err_exit:
+ dev_err(&drv_data->pdev->dev, "DMA RX Channel Not available");
+ pci_dev_put(drv_data->dmac1);
+}
+
+/**
+ * intel_mid_ssp_spi_dma_exit() - Release DMA ressources
+ * @drv_data: Pointer to the private driver data
+ */
+static void intel_mid_ssp_spi_dma_exit(struct driver_data *drv_data)
+{
+ if (!drv_data->dma_inited)
+ return;
+ dma_release_channel(drv_data->txchan);
+ dma_release_channel(drv_data->rxchan);
+ pci_dev_put(drv_data->dmac1);
+ drv_data->dma_inited = 0;
+}
+
+static void dma_transfer(struct driver_data *drv_data)
+{
+ dma_addr_t ssdr_addr;
+ struct dma_async_tx_descriptor *txdesc = NULL, *rxdesc = NULL;
+ struct dma_chan *txchan, *rxchan;
+ enum dma_ctrl_flags flag;
+ struct dma_slave_config *txconf, *rxconf;
+ struct device *dev = &drv_data->pdev->dev;
+
+ /* get Data Read/Write address */
+ ssdr_addr = (dma_addr_t)(drv_data->paddr + 0x10);
+ flag = DMA_PREP_INTERRUPT | DMA_CTRL_ACK;
+
+ /* 2. Prepare the RX dma transfer - DMA_FROM_DEVICE */
+ if (drv_data->rx_dma) {
+ rxconf = &drv_data->dmas_rx.dma_slave;
+ rxconf->src_addr = drv_data->rx_dma;
+ rxchan = drv_data->rxchan;
+ rxchan->device->device_control(rxchan, DMA_SLAVE_CONFIG,
+ (unsigned long) rxconf);
+ rxdesc = rxchan->device->device_prep_dma_memcpy
+ (rxchan, /* DMA Channel */
+ drv_data->rx_dma, /* DAR */
+ ssdr_addr, /* SAR */
+ drv_data->len, /* Data Length */
+ flag); /* Flag */
+ if (!rxdesc) {
+ dev_err(dev, "ERROR : rxdesc is null!");
+ return;
+ }
+ rxdesc->callback = dma_transfer_complete;
+ rxdesc->callback_param = &drv_data->rx_param;
+ drv_data->rxdma_done = 0;
+ }
+
+ /* 3. Prepare the TX dma transfer - DMA_TO_DEVICE */
+ if (drv_data->tx_dma) {
+ txconf = &drv_data->dmas_tx.dma_slave;
+ txconf->dst_addr = drv_data->rx_dma;
+ txchan = drv_data->txchan;
+ txchan->device->device_control(txchan, DMA_SLAVE_CONFIG,
+ (unsigned long) txconf);
+ txdesc = txchan->device->device_prep_dma_memcpy
+ (txchan, /* DMA Channel */
+ ssdr_addr, /* DAR */
+ drv_data->tx_dma, /* SAR */
+ drv_data->len, /* Data Length */
+ flag); /* Flag */
+ if (!txdesc) {
+ dev_err(dev, "ERROR : txdesc is null!");
+ return;
+ }
+ txdesc->callback = dma_transfer_complete;
+ txdesc->callback_param = &drv_data->tx_param;
+ drv_data->txdma_done = 0;
+ }
+
+ if (rxdesc)
+ rxdesc->tx_submit(rxdesc);
+ if (txdesc)
+ txdesc->tx_submit(txdesc);
+
+}
+
+
+/**
+ * map_dma_buffers() - Map DMA buffer before a transfer
+ * @drv_data: Pointer to the private driver data
+ */
+static int map_dma_buffers(struct driver_data *drv_data,
+ struct spi_message *msg,
+ struct spi_transfer *transfer)
+{
+ struct device *dev = &drv_data->pdev->dev;
+
+ if (unlikely(drv_data->dma_mapped)) {
+ dev_err(dev, "ERROR : DMA buffers already mapped");
+ return 0;
+ }
+ if (unlikely(msg->is_dma_mapped)) {
+ drv_data->rx_dma = transfer->rx_dma;
+ drv_data->tx_dma = transfer->tx_dma;
+ return 1;
+ }
+ if (drv_data->len > PCI_DMAC_MAXDI * drv_data->n_bytes) {
+ /* if length is too long we revert to programmed I/O */
+ return 0;
+ }
+
+ if (likely(drv_data->rx)) {
+ drv_data->rx_dma =
+ dma_map_single(dev, drv_data->rx,
+ drv_data->len, DMA_FROM_DEVICE);
+ if (unlikely(dma_mapping_error(dev, drv_data->rx_dma))) {
+ dev_err(dev, "ERROR : rx dma mapping failed");
+ return 0;
+ }
+ }
+ if (likely(drv_data->tx)) {
+ drv_data->tx_dma =
+ dma_map_single(dev, drv_data->tx,
+ drv_data->len, DMA_TO_DEVICE);
+ if (unlikely(dma_mapping_error(dev, drv_data->tx_dma))) {
+ dma_unmap_single(dev, drv_data->rx_dma,
+ drv_data->len, DMA_FROM_DEVICE);
+ dev_err(dev, "ERROR : tx dma mapping failed");
+ return 0;
+ }
+ }
+ return 1;
+}
+
+static void set_dma_width(struct driver_data *drv_data, int bits)
+{
+ struct dma_slave_config *rxconf, *txconf;
+ rxconf = &drv_data->dmas_rx.dma_slave;
+ txconf = &drv_data->dmas_tx.dma_slave;
+
+ if (bits <= 8) {
+ rxconf->src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ txconf->dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+ } else if (bits <= 16) {
+ rxconf->src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ txconf->dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ } else if (bits <= 32) {
+ rxconf->src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ txconf->dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ }
+}
+
+static void int_error_stop(struct driver_data *drv_data, const char* msg)
+{
+ void *reg = drv_data->ioaddr;
+
+ /* Stop and reset SSP */
+ iowrite32(drv_data->clear_sr, reg + SSSR);
+ iowrite32(ioread32(reg + SSCR1) & ~drv_data->int_cr1, reg + SSCR1);
+ iowrite32(0, reg + SSTO);
+ flush(drv_data);
+
+ dev_err(&drv_data->pdev->dev, "%s", msg);
+
+}
+
+static void int_transfer_complete(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ u32 sscr1;
+
+ dev_dbg(&drv_data->pdev->dev, "interrupt transfer complete");
+ /* Clear Status Register */
+ iowrite32(drv_data->clear_sr, reg + SSSR);
+
+ sscr1 = ioread32(reg + SSCR1);
+
+ /* Disable Triggers to DMA */
+ sscr1 &= ~drv_data->dma_cr1;
+
+ /* Disable Interrupt */
+ sscr1 &= ~drv_data->int_cr1;
+ iowrite32(sscr1, reg + SSCR1);
+
+ /* Stop getting Time Outs */
+ iowrite32(0, reg + SSTO);
+
+ /* Update total byte transfered return count actual bytes read */
+ drv_data->cur_msg->actual_length += drv_data->len -
+ (drv_data->rx_end - drv_data->rx);
+
+ drv_data->cur_msg->status = 0;
+ giveback(drv_data);
+ pm_runtime_put(&drv_data->pdev->dev);
+}
+
+static void transfer_complete(struct driver_data *drv_data)
+{
+ /* Update total byte transfered return count actual bytes read */
+ drv_data->cur_msg->actual_length +=
+ drv_data->len - (drv_data->rx_end - drv_data->rx);
+
+ drv_data->cur_msg->status = 0;
+ giveback(drv_data);
+ pm_runtime_put(&drv_data->pdev->dev);
+}
+
+static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
+{
+ void *reg = drv_data->ioaddr;
+ u32 irq_mask = (ioread32(reg + SSCR1) & SSCR1_TIE) ?
+ drv_data->mask_sr : drv_data->mask_sr & ~SSSR_TFS;
+
+ u32 irq_status = ioread32(reg + SSSR) & irq_mask;
+ if (irq_status & SSSR_ROR) {
+ int_error_stop(drv_data, "interrupt_transfer: fifo overrun");
+ return IRQ_HANDLED;
+ }
+
+ if (irq_status & SSSR_TINT) {
+ iowrite32(SSSR_TINT, reg + SSSR);
+ if (drv_data->read(drv_data)) {
+ int_transfer_complete(drv_data);
+ return IRQ_HANDLED;
+ }
+ }
+
+ /* Drain rx fifo, Fill tx fifo and prevent overruns */
+ do {
+ if (drv_data->read(drv_data)) {
+ int_transfer_complete(drv_data);
+ return IRQ_HANDLED;
+ }
+ } while (drv_data->write(drv_data));
+
+ if (drv_data->read(drv_data)) {
+ int_transfer_complete(drv_data);
+ return IRQ_HANDLED;
+ }
+
+ if (drv_data->tx == drv_data->tx_end)
+ iowrite32(ioread32(reg + SSCR1) & ~SSCR1_TIE, reg + SSCR1);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t ssp_int(int irq, void *dev_id)
+{
+ struct driver_data *drv_data = dev_id;
+ void *reg = drv_data->ioaddr;
+ u32 status = ioread32(reg + SSSR);
+
+ if (status & (SSSR_ROR | SSSR_TUR)) {
+ dev_dbg(&drv_data->pdev->dev,
+ "--- SPI ROR or TUR Occred : SSSR=%x", status);
+
+ if (drv_data->dma_mapped) {
+ iowrite32(SSSR_ROR, reg + SSSR); /* Clear ROR */
+ iowrite32(SSSR_TUR, reg + SSSR); /* Clear TUR */
+ return IRQ_HANDLED;
+ }
+ }
+
+ /* just return if this is not our interrupt */
+ if (!(ioread32(reg + SSSR) & drv_data->mask_sr))
+ return IRQ_NONE;
+
+ if (!drv_data->cur_msg) {
+ iowrite32(ioread32(reg + SSCR0) & ~SSCR0_SSE, reg + SSCR0);
+ iowrite32(ioread32(reg + SSCR1) & ~drv_data->int_cr1,
+ reg + SSCR1);
+ iowrite32(drv_data->clear_sr, reg + SSSR);
+
+ /* Never fail */
+
+ return IRQ_HANDLED;
+ }
+
+ return drv_data->transfer_handler(drv_data);
+}
+
+static void poll_transfer(unsigned long data)
+{
+ struct driver_data *drv_data = (struct driver_data *)data;
+
+ if (drv_data->tx)
+ while (drv_data->tx != drv_data->tx_end) {
+ drv_data->write(drv_data);
+ drv_data->read(drv_data);
+ }
+
+ while (!drv_data->read(drv_data))
+ cpu_relax();
+
+ transfer_complete(drv_data);
+}
+
+static unsigned int ssp_get_clk_div(int speed)
+{
+ u32 clk_div;
+
+ /*
+ * fabric clock: 100MHz
+ * SSP clock: 25MHz max
+ */
+ clk_div = max(100000000 / speed, 4);
+
+ return clk_div;
+}
+
+/**
+ * resume_transfer_work() - resume from pm_runtime sleep then
+ * perform transfer() work
+ */
+static void resume_transfer_work(struct work_struct *work)
+{
+ struct driver_data *drv_data = container_of(work, struct driver_data,
+ resume_transfer_work);
+ struct spi_message *msg;
+
+ pm_runtime_get_sync(&drv_data->pdev->dev);
+ WARN_ON(drv_data->pwrstate != PWRSTATE_ON);
+ msg = drv_data->cur_msg;
+ drv_data->cur_msg = NULL;
+ transfer(msg->spi, msg);
+}
+
+static int transfer(struct spi_device *spi, struct spi_message *msg)
+{
+ struct driver_data *drv_data = spi_master_get_devdata(spi->master);
+ struct chip_data *chip = NULL;
+ struct spi_transfer *transfer = NULL;
+ void *reg = drv_data->ioaddr;
+ int truth;
+ u8 bits;
+ u32 clk_div;
+ u32 speed;
+ u32 cr0;
+ u32 cr1;
+
+ if (unlikely(drv_data->pwrstate == PWRSTATE_OFF)) {
+ dev_dbg(&drv_data->pdev->dev, "transfer: busy, pwrstate:%d",
+ drv_data->pwrstate);
+ return -EIO;
+ }
+ if (unlikely(drv_data->pwrstate == PWRSTATE_IDLE)) {
+ truth = test_and_set_bit(PWRFLAG_RTRESUMING,
+ &drv_data->pwrflags);
+ if (truth > 0) {
+ WARN_ON(1);
+ return -EBUSY;
+ }
+ drv_data->cur_msg = msg;
+ queue_work(drv_data->wq, &drv_data->resume_transfer_work);
+ return 0;
+ }
+ msg->actual_length = 0;
+ msg->status = -EINPROGRESS;
+ drv_data->cur_msg = msg;
+
+ /* We handle only one transfer message since the protocol module has to
+ control the out of band signaling. */
+ transfer = list_entry(msg->transfers.next, struct spi_transfer,
+ transfer_list);
+
+ /* Setup the transfer state based on the type of transfer */
+ if (likely(!test_and_clear_bit(PWRFLAG_RTRESUMING,
+ &drv_data->pwrflags)))
+ pm_runtime_get(&drv_data->pdev->dev);
+ chip = spi_get_ctldata(msg->spi);
+ flush(drv_data);
+ drv_data->n_bytes = chip->n_bytes;
+ drv_data->tx = (void *)transfer->tx_buf;
+ drv_data->tx_end = drv_data->tx + transfer->len;
+ drv_data->rx = transfer->rx_buf;
+ drv_data->rx_end = drv_data->rx + transfer->len;
+ drv_data->rx_dma = transfer->rx_dma;
+ drv_data->tx_dma = transfer->tx_dma;
+ drv_data->len = transfer->len;
+ drv_data->write = drv_data->tx ? chip->write : null_writer;
+ drv_data->read = drv_data->rx ? chip->read : null_reader;
+
+ /* Change speed and bit per word on a per transfer */
+ cr0 = chip->cr0;
+ if (transfer->speed_hz || transfer->bits_per_word) {
+
+ bits = chip->bits_per_word;
+ speed = chip->speed_hz;
+
+ if (transfer->speed_hz)
+ speed = transfer->speed_hz;
+
+ clk_div = ssp_get_clk_div(speed);
+
+ if (transfer->bits_per_word)
+ bits = transfer->bits_per_word;
+
+ if (bits <= 8) {
+ drv_data->n_bytes = 1;
+ drv_data->read = drv_data->read != null_reader ?
+ u8_reader : null_reader;
+ drv_data->write = drv_data->write != null_writer ?
+ u8_writer : null_writer;
+ } else if (bits <= 16) {
+ drv_data->n_bytes = 2;
+ drv_data->read = drv_data->read != null_reader ?
+ u16_reader : null_reader;
+ drv_data->write = drv_data->write != null_writer ?
+ u16_writer : null_writer;
+ } else if (bits <= 32) {
+ drv_data->n_bytes = 4;
+ drv_data->read = drv_data->read != null_reader ?
+ u32_reader : null_reader;
+ drv_data->write = drv_data->write != null_writer ?
+ u32_writer : null_writer;
+ }
+ if (likely(chip->enable_dma))
+ set_dma_width(drv_data, bits);
+ cr0 = PNWL_CR0(clk_div, bits, spi, chip);
+ }
+
+ /* try to map dma buffer and do a dma transfer if successful */
+ if (likely(chip->enable_dma))
+ drv_data->dma_mapped = map_dma_buffers(drv_data, msg, transfer);
+ else {
+ WARN_ON(drv_data->dma_mapped != 0);
+ drv_data->dma_mapped = 0;
+ }
+
+ drv_data->transfer_handler = interrupt_transfer;
+ iowrite32(drv_data->clear_sr, reg + SSSR);
+ cr1 = chip->cr1;
+ iowrite32(chip->timeout, reg + SSTO);
+
+ if (likely(drv_data->dma_mapped))
+ cr1 |= drv_data->dma_cr1;
+ else if (!chip->poll_mode)
+ cr1 |= drv_data->int_cr1;
+
+ dev_dbg(&drv_data->pdev->dev,
+ "%s drv_data:%p len:%d n_bytes:%d cr0:%x cr1:%x",
+ (drv_data->dma_mapped ? "DMA io:" :
+ (chip->poll_mode ? "Poll io:" : "Intr io:")),
+ drv_data, drv_data->len, drv_data->n_bytes, cr0, cr1);
+
+ /* see if we need to reload the config registers */
+ truth = ioread32(reg + SSCR0) != cr0 ||
+ ((ioread32(reg + SSCR1) & SSCR1_CHANGE_MASK) !=
+ (cr1 & SSCR1_CHANGE_MASK));
+ if (unlikely(truth)) {
+ /* stop the SSP, and update the other bits */
+ iowrite32(cr0 & ~SSCR0_SSE, reg + SSCR0);
+ /* first set CR1 without interrupt and service enables */
+ iowrite32(cr1 & SSCR1_CHANGE_MASK, reg + SSCR1);
+ /* restart the SSP */
+ iowrite32(cr0, reg + SSCR0);
+ }
+
+ /* after chip select, release the data by enabling service
+ * requests and interrupts, without changing any mode bits */
+ iowrite32(cr1, reg + SSCR1);
+
+ if (likely(drv_data->dma_mapped)) {
+ /* transfer using DMA */
+ dma_transfer(drv_data);
+ } else if (chip->poll_mode) {
+ /* transfer using non interrupt polling */
+ tasklet_schedule(&drv_data->poll_transfer);
+ }
+ /*
+ * if not using dma or poll-mode, transfers are done
+ * using interrupt driven programmed I/O
+ */
+
+ return 0;
+}
+
+/**
+ * setup() - configures hardware according to given @chip
+ * @espi: ep93xx SPI controller struct
+ * @chip: chip specific settings
+ *
+ * This function sets up the actual hardware registers with settings given in
+ * @chip
+ */
+static int setup(struct spi_device *spi)
+{
+ struct intel_mid_ssp_spi_chip *chip_info = NULL;
+ struct chip_data *chip;
+ uint tx_thres = TX_THRESH_DFLT;
+ uint rx_thres = RX_THRESH_DFLT;
+ u32 clk_div;
+ struct driver_data *drv_data = spi_master_get_devdata(spi->master);
+
+ if (drv_data->pwrstate == PWRSTATE_OFF) {
+ dev_dbg(&drv_data->pdev->dev, "setup: busy, pwrstate:%d",
+ drv_data->pwrstate);
+ return -EIO;
+ }
+
+ if (!spi->bits_per_word)
+ spi->bits_per_word = 8;
+
+ if ((spi->bits_per_word < 4 || spi->bits_per_word > 32))
+ return -EINVAL;
+
+ /* Only alloc on first setup */
+ chip = spi_get_ctldata(spi);
+ if (!chip) {
+ chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
+ if (!chip) {
+ dev_err(&spi->dev,
+ "failed setup: can't allocate chip data");
+ return -ENOMEM;
+ }
+
+ chip->timeout = TIMOUT_DFLT;
+ }
+
+ /*
+ * protocol drivers may change the chip settings, so...
+ * if chip_info exists, use it
+ */
+ chip_info = spi->controller_data;
+
+ /* chip_info isn't always needed */
+ if (chip_info) {
+ if (chip_info->timeout)
+ chip->timeout = chip_info->timeout;
+
+ if (chip_info->tx_threshold)
+ tx_thres = chip_info->tx_threshold;
+ if (chip_info->rx_threshold)
+ rx_thres = chip_info->rx_threshold;
+ }
+ chip->enable_dma = TESTMODE(TESTMODE_ENABLE_DMA);
+ chip->poll_mode = TESTMODE(TESTMODE_ENABLE_POLL);
+ chip->enable_loopback = TESTMODE(TESTMODE_ENABLE_LOOPBACK);
+
+ if (spi->bits_per_word <= 8) {
+ chip->n_bytes = 1;
+ chip->read = u8_reader;
+ chip->write = u8_writer;
+
+ } else if (spi->bits_per_word <= 16) {
+ chip->n_bytes = 2;
+ chip->read = u16_reader;
+ chip->write = u16_writer;
+ } else if (spi->bits_per_word <= 32) {
+ chip->n_bytes = 4;
+ chip->read = u32_reader;
+ chip->write = u32_writer;
+ } else {
+ dev_err(&spi->dev, "invalid wordsize");
+ return -ENODEV;
+ }
+
+ if (chip->enable_dma) {
+ intel_mid_ssp_spi_dma_init(drv_data);
+ set_dma_width(drv_data, spi->bits_per_word);
+ }
+
+ chip->speed_hz = spi->max_speed_hz;
+ clk_div = ssp_get_clk_div(chip->speed_hz);
+
+ chip->threshold = (SSCR1_RxTresh(rx_thres) & SSCR1_RFT) |
+ (SSCR1_TxTresh(tx_thres) & SSCR1_TFT);
+ chip->bits_per_word = spi->bits_per_word;
+
+ chip->cr0 = PNWL_CR0(clk_div, spi->bits_per_word, spi, chip);
+ chip->cr1 = PNWL_CR1(spi, chip);
+
+ dev_dbg(&spi->dev,
+ "KHz:%d bpw:%d mode:%d dma:%d poll:%d loop:%d cr0:%x cr1:%x",
+ 100000 / clk_div, spi->bits_per_word, spi->mode & 0x3,
+ chip->enable_dma, chip->poll_mode, chip->enable_loopback,
+ chip->cr0, chip->cr1);
+
+ spi_set_ctldata(spi, chip);
+
+ return 0;
+}
+
+/**
+ * cleanup() - cleans up master controller specific state
+ * @spi: SPI device to cleanup
+ *
+ * This function releases master controller specific state for given @spi
+ * device.
+ */
+static void cleanup(struct spi_device *spi)
+{
+ struct chip_data *chip = spi_get_ctldata(spi);
+ struct driver_data *drv_data = spi_master_get_devdata(spi->master);
+
+ if (drv_data->dma_inited)
+ intel_mid_ssp_spi_dma_exit(drv_data);
+ kfree(chip);
+ spi_set_ctldata(spi, NULL);
+}
+
+static int intel_mid_ssp_spi_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct device *dev = &pdev->dev;
+ struct spi_master *master;
+ struct driver_data *drv_data;
+ int status = 0;
+ int pci_bar = 0;
+ void __iomem *syscfg_ioaddr;
+ unsigned long syscfg;
+ u8 ssp_cfg;
+ int pos;
+
+ /* Check if the SSP we are probed for has been allocated to */
+ /* operate as SPI master. This information is get from the */
+ /* field adid of the Vendor-Specific PCI capability which is */
+ /* used as a configuration register. */
+ pos = pci_find_capability(pdev, PCI_CAP_ID_VNDR);
+ if (pos > 0) {
+ pci_read_config_byte(pdev,
+ pos + VNDR_CAPABILITY_ADID_OFFSET,
+ &ssp_cfg);
+ } else {
+ dev_info(dev, "No Vendor Specific PCI capability");
+ goto err_abort_probe;
+ }
+ if ((SSP_CFG_GET_MODE(ssp_cfg) != SSP_CFG_SPI_MODE_ID) ||
+ SSP_CFG_IS_SPI_SLAVE(ssp_cfg)) {
+ dev_info(dev, "Unsupported SSP mode (%02xh)",
+ ssp_cfg);
+ goto err_abort_probe;
+ }
+
+ dev_info(&pdev->dev, "found PCI SSP controller(ID: %04xh:%04xh"
+ " cfg: %02xh)", pdev->vendor, pdev->device, ssp_cfg);
+
+ status = pci_enable_device(pdev);
+ if (status)
+ return status;
+
+ /* Allocate Slave with space for drv_data and null dma buffer */
+ master = spi_alloc_master(dev, sizeof(struct driver_data));
+
+ if (!master) {
+ dev_err(dev, "cannot alloc spi_master");
+ status = -ENOMEM;
+ goto err_free_0;
+ }
+
+ drv_data = spi_master_get_devdata(master);
+ drv_data->master = master;
+ drv_data->pdev = pdev;
+ drv_data->pwrstate = PWRSTATE_ON;
+ drv_data->wq = create_workqueue(DRIVER_NAME);
+ INIT_WORK(&drv_data->resume_transfer_work, resume_transfer_work);
+
+ master->mode_bits = SPI_CPOL | SPI_CPHA;
+ master->bus_num = SSP_CFG_GET_SPI_BUS_NB(ssp_cfg);
+ master->num_chipselect = 1;
+ master->cleanup = cleanup;
+ master->setup = setup;
+ master->transfer = transfer;
+
+ /* get basic io resource and map it */
+ drv_data->paddr = pci_resource_start(pdev, pci_bar);
+ drv_data->iolen = pci_resource_len(pdev, pci_bar);
+
+ status = pci_request_region(pdev, pci_bar, dev_name(dev));
+ if (status)
+ goto err_free_1;
+
+ drv_data->ioaddr = ioremap_nocache(drv_data->paddr, drv_data->iolen);
+ if (!drv_data->ioaddr) {
+ status = -ENOMEM;
+ goto err_free_2;
+ }
+ dev_dbg(dev, "paddr = : %08lx", drv_data->paddr);
+ dev_dbg(dev, "ioaddr = : %p", drv_data->ioaddr);
+ dev_dbg(dev, "attaching to IRQ: %04x", pdev->irq);
+
+ /* Attach to IRQ */
+ drv_data->irq = pdev->irq;
+
+ status = request_irq(drv_data->irq, ssp_int, IRQF_SHARED,
+ "intel_mid_ssp_spi", drv_data);
+ if (status < 0) {
+ dev_err(dev, "can not get IRQ %d", drv_data->irq);
+ goto err_free_3;
+ }
+
+ /* get base address of DMA selector. */
+ syscfg = drv_data->paddr - SYSCFG;
+ syscfg_ioaddr = ioremap_nocache(syscfg, 0x10);
+ if (!syscfg_ioaddr) {
+ status = -ENOMEM;
+ goto err_free_3;
+ }
+
+ iowrite32(ioread32(syscfg_ioaddr) | 2, syscfg_ioaddr);
+
+ drv_data->int_cr1 = SSCR1_TIE | SSCR1_RIE | SSCR1_TINTE;
+ drv_data->dma_cr1 = SSCR1_TSRE | SSCR1_RSRE | SSCR1_TRAIL;
+ drv_data->clear_sr = SSSR_ROR | SSSR_TINT;
+ drv_data->mask_sr = SSSR_TINT | SSSR_RFS | SSSR_TFS | SSSR_ROR;
+
+ tasklet_init(&drv_data->poll_transfer,
+ poll_transfer, (unsigned long)drv_data);
+
+ /* Load default SSP configuration */
+ dev_info(dev, "setup default SSP configuration");
+ iowrite32(0, drv_data->ioaddr + SSCR0);
+ iowrite32(SSCR1_RxTresh(RX_THRESH_DFLT) |
+ SSCR1_TxTresh(TX_THRESH_DFLT),
+ drv_data->ioaddr + SSCR1);
+ iowrite32(SSCR0_Motorola | SSCR0_DataSize(8), drv_data->ioaddr + SSCR0);
+ iowrite32(0, drv_data->ioaddr + SSTO);
+ iowrite32(PNWL_SSPSP, drv_data->ioaddr + SSPSP);
+
+ /* Register with the SPI framework */
+ dev_info(&pdev->dev, "register with SPI framework (as SPI%d)",
+ master->bus_num);
+ status = spi_register_master(master);
+ if (status != 0) {
+ dev_err(dev, "problem registering driver");
+ goto err_free_4;
+ }
+
+ pci_set_drvdata(pdev, drv_data);
+
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_idle(&pdev->dev);
+ pm_runtime_allow(dev);
+
+ return status;
+
+err_free_4:
+ free_irq(drv_data->irq, drv_data);
+err_free_3:
+ iounmap(drv_data->ioaddr);
+err_free_2:
+ pci_release_region(pdev, pci_bar);
+err_free_1:
+ spi_master_put(master);
+err_free_0:
+ pci_disable_device(pdev);
+
+ return status;
+err_abort_probe:
+ dev_info(dev, "Abort probe for SSP %04xh:%04xh",
+ pdev->vendor, pdev->device);
+ return -ENODEV;
+}
+
+static void __devexit intel_mid_ssp_spi_remove(struct pci_dev *pdev)
+{
+ struct driver_data *drv_data = pci_get_drvdata(pdev);
+
+ if (!drv_data)
+ return;
+
+ pci_set_drvdata(pdev, NULL);
+
+ free_irq(drv_data->irq, drv_data);
+
+ iounmap(drv_data->ioaddr);
+
+ pci_release_region(pdev, 0);
+
+ spi_unregister_master(drv_data->master);
+
+ pci_disable_device(pdev);
+
+ return;
+}
+
+/*
+ * for now IDLE and OFF states are treated the same
+ */
+static int _pm_suspend(struct pci_dev *pdev, int to)
+{
+ struct driver_data *drv_data = pci_get_drvdata(pdev);
+ void *reg = drv_data->ioaddr;
+ int from = drv_data->pwrstate;
+ u32 sssr;
+
+
+ if (to != PWRSTATE_IDLE && to != PWRSTATE_OFF) {
+ dev_err(&pdev->dev, "ERROR: suspend: invalid dst pwrstate %x",
+ to);
+ return -EINVAL;
+ }
+
+ switch (from) {
+ case PWRSTATE_ON:
+ dev_dbg(&pdev->dev, "suspend: turn off SSP");
+ if (have_fifo_data(drv_data, &sssr)) {
+ dev_err(&pdev->dev,
+ "ERROR: suspend: i/o present! sssr:%x", sssr);
+ return -EBUSY;
+ }
+ tasklet_disable(&drv_data->poll_transfer);
+ drv_data->pwrstate = to;
+ iowrite32(0, reg + SSCR0);
+ dev_dbg(&pdev->dev, "suspend: cr0:%x cr1:%x sssr:%x",
+ ioread32(reg + SSCR0), ioread32(reg + SSCR1),
+ ioread32(reg + SSSR));
+ break;
+ case PWRSTATE_IDLE:
+ case PWRSTATE_OFF:
+ drv_data->pwrstate = to;
+ break;
+ default:
+ dev_err(&pdev->dev, "ERROR: suspend: invalid src pwrstate %x",
+ from);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/*
+ * for now IDLE and OFF states are treated the same
+ */
+static void _pm_resume(struct pci_dev *pdev)
+{
+ struct driver_data *drv_data = pci_get_drvdata(pdev);
+ void *reg = drv_data->ioaddr;
+
+ switch (drv_data->pwrstate) {
+ default:
+ dev_err(&pdev->dev, "ERROR: resume: invalid src pwrstate %x",
+ drv_data->pwrstate);
+ /* fall through ... */
+ case PWRSTATE_IDLE:
+ case PWRSTATE_OFF:
+ dev_dbg(&pdev->dev, "resume: turn on SSP");
+
+ /*
+ * we don't bother reconfiguring the registers
+ * on resume - that will get done when transfer()
+ * is called
+ */
+ tasklet_enable(&drv_data->poll_transfer);
+ dev_dbg(&pdev->dev, "resume: cr0:%x cr1:%x sssr:%x",
+ ioread32(reg + SSCR0), ioread32(reg + SSCR1),
+ ioread32(reg + SSSR));
+
+ drv_data->pwrstate = PWRSTATE_ON;
+ break;
+ case PWRSTATE_ON:
+ break;
+ }
+}
+
+
+#ifdef CONFIG_PM
+
+static int intel_mid_ssp_spi_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ int retval;
+ struct driver_data *drv_data = pci_get_drvdata(pdev);
+
+ dev_dbg(&pdev->dev, "%s called", __func__);
+ if (drv_data->pwrstate != PWRSTATE_ON)
+ dev_warn(&pdev->dev, "suspend: !on, pwrstate:%d",
+ drv_data->pwrstate);
+ retval = _pm_suspend(pdev, PWRSTATE_OFF);
+ if (retval)
+ return retval;
+ retval = pci_prepare_to_sleep(pdev);
+ if (retval) {
+ dev_err(&pdev->dev, "suspend: prepare to sleep failed");
+ return retval;
+ }
+ pci_disable_device(pdev);
+ return 0;
+}
+
+static int intel_mid_ssp_spi_resume(struct pci_dev *pdev)
+{
+ int retval;
+ struct driver_data *drv_data = pci_get_drvdata(pdev);
+
+ dev_dbg(&pdev->dev, "%s called", __func__);
+ if (drv_data->pwrstate != PWRSTATE_OFF)
+ dev_warn(&pdev->dev, "resume: !off, pwrstate:%d",
+ drv_data->pwrstate);
+ retval = pci_enable_device(pdev);
+ if (retval) {
+ dev_err(&pdev->dev, "resume: back from sleep failed");
+ return retval;
+ }
+ retval = pci_back_from_sleep(pdev);
+ if (retval) {
+ dev_err(&pdev->dev, "resume: back from sleep failed");
+ return retval;
+ }
+ _pm_resume(pdev);
+ return 0;
+}
+
+#else
+#define intel_mid_ssp_spi_suspend NULL
+#define intel_mid_ssp_spi_resume NULL
+#endif /* CONFIG_PM */
+
+
+static int intel_mid_ssp_spi_pm_runtime_resume(struct device *dev)
+{
+ int retval;
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct driver_data *drv_data = pci_get_drvdata(pdev);
+
+ dev_dbg(dev, "%s called", __func__);
+ if (drv_data->pwrstate == PWRSTATE_ON)
+ return 0;
+ if (drv_data->pwrstate != PWRSTATE_IDLE)
+ dev_warn(&pdev->dev, "rt resume: !idle, pwrstate:%d",
+ drv_data->pwrstate);
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ retval = pci_enable_device(pdev);
+ if (retval)
+ return retval;
+ _pm_resume(pdev);
+
+ return retval;
+}
+
+static int intel_mid_ssp_spi_pm_runtime_suspend(struct device *dev)
+{
+ int retval;
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct driver_data *drv_data = pci_get_drvdata(pdev);
+
+ dev_dbg(dev, "%s called", __func__);
+ if (drv_data->pwrstate != PWRSTATE_ON)
+ dev_warn(&pdev->dev, "rt suspend: !on, pwrstate:%d",
+ drv_data->pwrstate);
+ retval = _pm_suspend(pdev, PWRSTATE_IDLE);
+ if (retval)
+ return retval;
+ pci_save_state(pdev);
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, PCI_D3hot);
+
+ return retval;
+}
+
+static int intel_mid_ssp_spi_pm_runtime_idle(struct device *dev)
+{
+ dev_dbg(dev, "%s called", __func__);
+ pm_schedule_suspend(dev, 100);
+ return -EBUSY;
+}
+
+static const struct dev_pm_ops intel_mid_ssp_spi_pm = {
+ .runtime_resume = intel_mid_ssp_spi_pm_runtime_resume,
+ .runtime_suspend = intel_mid_ssp_spi_pm_runtime_suspend,
+ .runtime_idle = intel_mid_ssp_spi_pm_runtime_idle,
+};
+
+static const struct pci_device_id pci_ids[] __devinitdata = {
+ { PCI_VDEVICE(INTEL, 0x0816) },
+ { }
+};
+
+static struct pci_driver intel_mid_ssp_spi_driver = {
+ .driver = {
+ .pm = &intel_mid_ssp_spi_pm,
+ },
+ .name = DRIVER_NAME,
+ .id_table = pci_ids,
+ .probe = intel_mid_ssp_spi_probe,
+ .remove = __devexit_p(intel_mid_ssp_spi_remove),
+ .suspend = intel_mid_ssp_spi_suspend,
+ .resume = intel_mid_ssp_spi_resume,
+};
+
+static int __init intel_mid_ssp_spi_init(void)
+{
+ return pci_register_driver(&intel_mid_ssp_spi_driver);
+}
+late_initcall(intel_mid_ssp_spi_init);
+
+static void __exit intel_mid_ssp_spi_exit(void)
+{
+ pci_unregister_driver(&intel_mid_ssp_spi_driver);
+}
+module_exit(intel_mid_ssp_spi_exit);
diff --git a/drivers/spi/intel_mid_ssp_spi_def.h
b/drivers/spi/intel_mid_ssp_spi_def.h
new file mode 100644
index 0000000..4610d62
--- /dev/null
+++ b/drivers/spi/intel_mid_ssp_spi_def.h
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) Intel 2010
+ * Ken Mills <ken.k.mi...@intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
+ * USA
+ *
+ */
+#ifndef INTEL_MID_SSP_SPI_DEF_H_
+#define INTEL_MID_SSP_SPI_DEF_H_
+
+
+/*
+ * Penwell SSP register definitions
+ */
+
+#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */
+#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */
+#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */
+#define SSCR0_Motorola (0x0 << 4) /* Motorola's SPI mode */
+#define SSCR0_ECS (1 << 6) /* External clock select */
+#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */
+
+
+#define SSCR0_SCR (0x000fff00) /* Serial Clock Rate (mask) */
+#define SSCR0_SerClkDiv(x) (((x) - 1) << 8) /* Divisor [1..4096] */
+#define SSCR0_EDSS (1 << 20) /* Extended data size select */
+#define SSCR0_NCS (1 << 21) /* Network clock select */
+#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun int mask */
+#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun int mask */
+#define SSCR0_FRDC (0x07000000) /* Frame rate divider control
(mask) */
+#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24) /* Time slots per frame */
+#define SSCR0_ADC (1 << 30) /* Audio clock select */
+#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */
+
+
+#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
+#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
+#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */
+#define SSCR1_SPO (1 << 3) /* SSPSCLK polarity setting */
+#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */
+#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */
+#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */
+#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
+#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */
+#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
+
+#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */
+#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */
+#define SSSR_BSY (1 << 4) /* SSP Busy */
+#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */
+#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
+#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
+#define SSSR_TFL (0x0f00) /* Transmit FIFO Level (mask) */
+#define SSSR_RFL (0xf000) /* Receive FIFO Level (mask) */
+
+#define SSCR0_TIM (1 << 23) /* Transmit FIFO Under Run Int Mask */
+#define SSCR0_RIM (1 << 22) /* Receive FIFO Over Run int Mask */
+#define SSCR0_NCS (1 << 21) /* Network Clock Select */
+#define SSCR0_EDSS (1 << 20) /* Extended Data Size Select */
+
+#define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */
+#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
+#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
+#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
+#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
+#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */
+#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */
+#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */
+#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */
+#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */
+#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */
+#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */
+#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */
+#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */
+#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */
+#define SSCR1_PINTE (1 << 18) /* Trailing Byte Interupt Enable */
+#define SSCR1_IFS (1 << 16) /* Invert Frame Signal */
+#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */
+#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */
+
+#define SSSR_BCE (1 << 23) /* Bit Count Error */
+#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */
+#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */
+#define SSSR_EOC (1 << 20) /* End Of Chain */
+#define SSSR_TINT (1 << 19) /* Receiver Time-out
Interrupt */
+#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
+
+#define SSPSP_FSRT (1 << 25) /* Frame Sync Relative Timing */
+#define SSPSP_DMYSTOP(x) ((x) << 23) /* Dummy Stop */
+#define SSPSP_SFRMWDTH(x) ((x) << 16) /* Serial Frame Width */
+#define SSPSP_SFRMDLY(x) ((x) << 9) /* Serial Frame Delay */
+#define SSPSP_DMYSTRT(x) ((x) << 7) /* Dummy Start */
+#define SSPSP_STRTDLY(x) ((x) << 4) /* Start Delay */
+#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */
+#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */
+#define SSPSP_SCMODE(x) ((x) << 0) /* Serial Bit Rate Clock
Mode */
+
+#define SSCR0 0x00
+#define SSCR1 0x04
+#define SSSR 0x08
+#define SSITR 0x0c
+#define SSDR 0x10
+#define SSTO 0x28
+#define SSPSP 0x2c
+#define SYSCFG 0x20bc0
+
+/* SSP assignement configuration from PCI config */
+#define SSP_CFG_GET_MODE(ssp_cfg) ((ssp_cfg) & 0x07)
+#define SSP_CFG_GET_SPI_BUS_NB(ssp_cfg) (((ssp_cfg) >> 3) & 0x07)
+#define SSP_CFG_IS_SPI_SLAVE(ssp_cfg) ((ssp_cfg) & 0x40)
+#define SSP_CFG_SPI_MODE_ID 1
+/* adid field offset is 6 inside the vendor specific capability */
+#define VNDR_CAPABILITY_ADID_OFFSET 6
+
+/* spi_board_info.controller_data for SPI slave devices,
+ * copied to spi_device.platform_data ... mostly for dma tuning
+ */
+struct intel_mid_ssp_spi_chip {
+ u8 tx_threshold;
+ u8 rx_threshold;
+ u8 dma_burst_size;
+ u32 timeout;
+ u16 extra_data[5];
+};
+
+
+#endif /* INTEL_MID_SSP_SPI_DEF_H_ */
--
1.7.2.3
------------------------------------------------------------------------------
Special Offer-- Download ArcSight Logger for FREE (a $49 USD value)!
Finally, a world-class log management solution at an even better price-free!
Download using promo code Free_Logger_4_Dev2Dev. Offer expires
February 28th, so secure your free ArcSight Logger TODAY!
http://p.sf.net/sfu/arcsight-sfd2d
_______________________________________________
spi-devel-general mailing list
spi-devel-general@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/spi-devel-general
