Hi Tom, > because of SRH
Ok I buy this that there are devices which do check checksum and are not final destination of the packets ... I was more talking about plain forwarding devices (aka P routers). Then I doubt firewalls would be sitting in the core of the networks. But let me come black to what I believe is the main disconnect. Why SRH would cause an issue ? I think there is claimed issue *ONLY* with SRv6 packets which are not encapsulated - call it raw - sent by the hosts which talk SRv6 and sent with more then one SID/uSID which may get swapped on the way. Because only in those cases the destination address will be changing while checksum of the tunnel header will not be zero. So what we should I think discuss are really B.1 and B.2.2 cases. Francois, Pablo - could you comment on this how often do we see those type of SRv6 deployments ? And also could you comment if operator who enables SRv6 in the first place sees those checksum errors how difficult is to address it ? Thx, Robert On Thu, Mar 28, 2024 at 3:29 PM Tom Herbert <t...@herbertland.com> wrote: > On Thu, Mar 28, 2024 at 6:26 AM Robert Raszuk <rob...@raszuk.net> wrote: > > > > Hi Alvaro, > > > > On this specific topic I think you have flatted it a bit too much. > > > > These are apparently the options on the table: > > > > A) Original packet get's encapsulated with IPv6 header > > > > A.1 SHR is added to it > > > > A.1.1. Regular SIDs are used > > A.1.2 Compresses SIDs are used > > > > A.2 SRH is not added to it > > > > A.2.1. Regular SID is used as destination > > A.2.2 Compresses SIDs are used in a container > > A.2.3 Compresses SID is used > > > > B) Original packet get's send from SRv6 host (without encapsulation) > > > > B.1 SHR is added to it > > > > B.1.1. Regular SIDs are used > > B.1.2 Compresses SIDs are used > > > > B.2 SRH is not added to it > > > > B.2.1. Regular SID is used as destination > > B.2.2 Compresses SIDs are used in a container > > B.2.3 Compresses SID is used > > > > So within all checksum related discussions so far it seems that the only > concern is about B.2.2 and perhaps B.1 however folks did state that if > there is SRH added there is no issue so I am not sure how the presence of > SRH fixes it. > > > > Maybe there was some assumption that presence of SRH mandates > encapsulation, but I do not believe this is the case for native SRv6 hosts. > > > > All in all I think it should be no business for transit nodes to verify > packet's upper layer checksum. I do not know if there is any RFC which > would describe what is an expected behavior for transit nodes or even say > that they MAY do it. > > Robert, > > I can go further than that. I believe that intermediate nodes have no > business parsing into the transport layer, and yet firewalls do that > all the time even though there is no standard RFC on it (I've asked > for someone to formalize the requirements of firewalls, but to no > avail). Validating the checksum in flight is an instance of this, and > there are devices that commonly do this in deployment. Protocol > specific checksum offload in NICs is one example. Also, if someone is > seeing checksum failures in their network, an obvious action is to > sample packets from routers in the path and look at the traces. If the > checksum is incorrect on the wire because of SRH then the operator > sees a whole bunch of checksum errors at the router, but has no way to > distinguish those packets that are actually good from those that are > bad. > > It's a long established convention in IP that the transport checksum > is maintained to be correct on the wire-- this is done in NAT by > adjusting the checksum directly, there's also checksum neutral NAT > that adjusts another part of the IPv6 header to keep the transport > layer checksum correct. IMO, deviating from this convention is risky, > not just to SRH packets but that can have collateral damage like > breaking the user's ability to debug bad links as I described above. > > Tom > > > > > Kind regards, > > Robert > > > > > > > > On Thu, Mar 28, 2024 at 1:06 PM Alvaro Retana <aretana.i...@gmail.com> > wrote: > >> > >> Focusing on the C-SID draft, some have suggested requiring the > >> presence of the SRH whenever C-SIDs are used. Please discuss whether > >> that is the desired behavior (or not) -- please be specific when > >> debating the benefits or consequences of either behavior. > >> > >> Please keep the related (but independent) discussion of requiring the > >> SRH whenever SRv6 is used separate. This larger topic may impact > >> several documents and is better handled in a different thread (with > >> 6man and spring included). > >> > >> Thanks! > >> > >> Alvaro > >> -- for spring-chairs > >> > >> -------------------------------------------------------------------- > >> IETF IPv6 working group mailing list > >> i...@ietf.org > >> Administrative Requests: https://www.ietf.org/mailman/listinfo/ipv6 > >> -------------------------------------------------------------------- > > > > -------------------------------------------------------------------- > > IETF IPv6 working group mailing list > > i...@ietf.org > > Administrative Requests: https://www.ietf.org/mailman/listinfo/ipv6 > > -------------------------------------------------------------------- >
_______________________________________________ spring mailing list spring@ietf.org https://www.ietf.org/mailman/listinfo/spring
