Joe Hankins - are you out there?  Ride in and save the day here.

What do you think "at least OH2" means?  Can you shed any light on the
difference between a OH1 and OH2 fire?  How about between a OH2 and EH1
fire?  What heat release characteristics would be associated with each? 
Is there any effort in the standards development process to relate fire
size to sprinkler density for the NFPA 13 area/density fires (thereby
linking a particular hazard to a particular curve), perhaps factoring in
room height, ceiling slope, sprinkler temperature and RTI also?

Bill Brooks

William N. Brooks, P.E.
Brooks Fire Protection Engineering Inc.
372 Wilett Drive
Severna Park, MD 21146
410-544-3620 Phone
410-544-3032 FAX
412-400-6528 Cell

-------- Original Message --------
Subject: RE: Glass Fiber Reinforced Resin Manufacturing
From: <[EMAIL PROTECTED]>
Date: Mon, February 18, 2008 8:52 am
To: <[email protected]>

Thanks for the reference. Note the minimal wording in the phrase "AT
LEAST Ord. Haz 2...." Under some circumstances OH2 might be
acceptable, think of an auto body or boat shop where they might do some
occasional small scale resin spraying for instance.

First thing is what the owner wants as far as a classification is
unimportant, what the codes say is what makes the determination. I hear
this kind of junk all the time.

I had a well known client of this type, their products were tubs and tub
surrounds. The mfg. area was .3/3000, wet pipe systems, spray booths
were sprinkled within as well as in the ductwork and behind filters,
Chemical storage was in cut-off rooms with some of the Class I stuff in
UL listed cabinets. The warehouse was a higher density since they had
crated and boxed products, pallets, and other misc. stuff stacked and
racked over 25ft high but I can't remember what that area design
criteria was.

Sounds like you got an Engineer and owner just looking for a simple
boiler plate answer and who really don't have the expertise to do a
proper analysis. But if you are stuck with this project what can you
do? The engineer is the hired "expert" as far as the owner is
concerned, so you either go along and install what he has specified or
pass on the job. If he is going to stand on his OH2 classification and
you have concerns over the adequacy of that, I'd be writing a few
letters so that there is a record of your questioning the decision and
your concern over it's appropriateness.

As far as when do you go by NFPA 30 versus NFPA 13, use the decision
trees in 30 as well as take a look at the various charts. They give
quantities and types of containers and arrangements in relation to what
the protection criteria should be and when it is acceptable to refer
back to specific protection schemes out of NFPA 13.



Craig L. Prahl, CET
Fire Protection Group
Mechanical Department
CH2MHILL
Lockwood Greene
1500 International Drive
PO Box 491, Spartanburg, SC 29304-0491
Direct - 864.599.4102
Fax - 864.599.8439
[EMAIL PROTECTED]
http://www.lg.com


-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of A.P.Silva
Sent: Friday, February 15, 2008 1:10 PM
To: [email protected]
Subject: RE: Glass Fiber Reinforced Resin Manufacturing

The following is from the NFPA 33, 2000 edition:

"15.3 Fire Protection.
Resin application areas shall be protected by an automatic sprinkler
system that is designed and installed in accordance with the
requirements of NFPA 13, Standard for the Installation of Sprinkler
Systems, for at least Ordinary Hazard, Group 2 occupancies."

The owner agrees with the engineer that the entire building can be OH2.
He has conceded that the storage area for plastic molds can be designed
for miscellaneous plastic storage and will have a storage area for the
flammable liquids that can be designed as per NFPA 30. He wants the rest
of the building to OH2 and argues that the flammable liquids in this
area is incidental for the process. Is there a quantity beyond which it
would be considered storage, and requiring compliance with NFPA 30?

Tony

-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of
[EMAIL PROTECTED]
Sent: February 15, 2008 10:28 AM
To: [email protected]
Subject: RE: Glass Fiber Reinforced Resin Manufacturing

Careful, Acetone is 1B, MEKP varies depending on composition and mfgr
from Class II to IIIB, PR's are another animal that requires special
attention.
Acetones are usually protected by foam-water, but this depends on the
quantities you are dealing with. Small qtys don't warrant F-W systems.
Using UL listed Flammable storage cabinets can also be a help.

It's great they are storing the PR's in resin rooms, do they get pumped
or are they carried in containers to the process/mfg areas. Two
separate issues.

Again another Special Hazards application that should be analyzed by
someone with Spec. Haz experience. These things are not boiler plate.
But OH2, no, doubt it highly, more like EH1 as a minimum or greater
depending on other factors.

Can't help with the NFPA 33 reference, don't have access to that old of
a copy. Can you help?

This is going to take more than a few minutes to answer.


Craig L. Prahl, CET
Fire Protection Group
Mechanical Department
CH2MHILL
Lockwood Greene
1500 International Drive
PO Box 491, Spartanburg, SC 29304-0491
Direct - 864.599.4102
Fax - 864.599.8439
[EMAIL PROTECTED]
http://www.lg.com


-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of A.P.Silva
Sent: Friday, February 15, 2008 2:24 AM
To: [email protected]
Subject: Glass Fiber Reinforced Resin Manufacturing

A building is being used for manufacuring Glass fiber reinforced resin
products. (I think the products are bath tubs etc., but not sure yet).
Some material used, such as Polyester Resins, Methyl Ethyl Ketone
Peroxyde (MEKP), Acetone etc. are class 1C flammable liquids.

The owner states that "Polyester resins will be stored in resin rooms.
Acetone in certified containers throughout shop space. And MEKP
catalysts will be stored in certified containers at workstations. Also,
composite plastic molds will be stored on racks, 5 to 12 feet high."

The engineer of record has specified OH2 for the building and when
questioned is directing to NFPA 33, 2000, section 15.3.

I think the storage areas have to be designed as per NFPA 30 for
flammable liquids, and as per NFPA 13 for plastic storage. Will the
storage quantities be a deciding factor (for selecting OH2)?

Will the process areas and spray application areas be OH2 (as per NFPA
33)?

Tony

_______________________________________________
Sprinklerforum mailing list
[email protected]
http://lists.firesprinkler.org/mailman/listinfo/sprinklerforum

To Unsubscribe, send an email
to:[EMAIL PROTECTED]
(Put the word unsubscribe in the subject field)
_______________________________________________
Sprinklerforum mailing list
[email protected]
http://lists.firesprinkler.org/mailman/listinfo/sprinklerforum

To Unsubscribe, send an email
to:[EMAIL PROTECTED]
(Put the word unsubscribe in the subject field)

_______________________________________________
Sprinklerforum mailing list
[email protected]
http://lists.firesprinkler.org/mailman/listinfo/sprinklerforum

To Unsubscribe, send an email
to:[EMAIL PROTECTED]
(Put the word unsubscribe in the subject field)
_______________________________________________
Sprinklerforum mailing list
[email protected]
http://lists.firesprinkler.org/mailman/listinfo/sprinklerforum

To Unsubscribe, send an email
to:[EMAIL PROTECTED]
(Put the word unsubscribe in the subject field)


_______________________________________________
Sprinklerforum mailing list
[email protected]
http://lists.firesprinkler.org/mailman/listinfo/sprinklerforum

To Unsubscribe, send an email to:[EMAIL PROTECTED]
(Put the word unsubscribe in the subject field)

Reply via email to