>The reason real railroads have eliminated the coned tread of locomotives is 
> traction. The contact{ are} AREA is greater when the wheel is contacting 
> the rail across the whole tread, where as the cone wheel has a very tiny 
> contact area, which gives you a MUCH better chance to slip!
 
I don't think it is quite that simple, as I believe the rails were canted 
inwards at the same angle as the wheel taper?  And also (just to add to the 
confusion) the possibly tiny contact area has much greater force acting on it 
(lbs/sq-in) so it offers adhesion almost as good as the larger contact patch?
 
However, the PRR Standard Plans on railfan.net don't show any such tilt/camber 
so I guess I'm wrong.
http://prr.railfan.net/standards/standards.cgi?plan=56773--
(Lots of good stuff on that collection - the index link is at the bottom, if 
you don't already have it bookmarked.)
 
Pete
410-533-4219
 
 
-----Original Message-----
From: [EMAIL PROTECTED]
To: [email protected]
Sent: Wed, 29 Nov 2006 3:00 PM
Subject: SSLiveSteam Digest, Vol 15, Issue 17


Send SSLiveSteam mailing list submissions to
    [email protected]

To subscribe or unsubscribe via the World Wide Web, visit
    http://postfix.45mm.com/mailman/listinfo/sslivesteam
or, via email, send a message with subject or body 'help' to
    [EMAIL PROTECTED]

You can reach the person managing the list at
    [EMAIL PROTECTED]

When replying, please edit your Subject line so it is more specific
than "Re: Contents of SSLiveSteam digest..."


Today's Topics:

   1. Re: O gauge wheel profile (Tom Jones)
   2. Re: O gauge wheel profile (Keith Taylor)
   3. Re: O gauge wheel profile (Sam)
   4. Re: O gauge wheel profile (Mike Chaney)
   5. Re: Wheel taper ([EMAIL PROTECTED])
   6. Re: Wheel taper (Keith Taylor)
   7. Re: Wheel taper (Keith Taylor)
   8. Dezincification of brass (Jeffrey Williams)
   9. Re: O gauge wheel profile - Off List (Tom Jones)
  10. (no subject) (Arthur S. Cohen)
  11. Fw: (Arthur S. Cohen)


----------------------------------------------------------------------

Message: 1
Date: Tue, 28 Nov 2006 14:06:29 -0700
From: "Tom Jones" <[EMAIL PROTECTED]>
Subject: Re: [SSLiveSteam] O gauge wheel profile
To: [email protected]
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; format=flowed

I didn't think to mention it until I had seen Sam's question, but this will 
be garden based.

Sam-

Thanks for you info.  I will be looking into it right away.  Also, I am not 
sure if I am misunderstanding your reply or not, but I was refering to 
'L.B.S.C' the man.  In one of his design booklets for an O gauge locomotive, 
he had his preference for the wheel profile.

Keith-

Thanks for the input!  Strangley enough I have heard of no coneing on the 
tread before for both prototypes and models.  It will be interesting to see 
if there is an outcry or not. :)

Once again, thanks for the input!

-Mitchell

_________________________________________________________________
Get FREE company branded e-mail accounts and business Web site from 
Microsoft Office Live 
http://clk.atdmt.com/MRT/go/mcrssaub0050001411mrt/direct/01/



------------------------------

Message: 2
Date: Tue, 28 Nov 2006 16:26:23 -0500
From: "Keith Taylor" <[EMAIL PROTECTED]>
Subject: Re: [SSLiveSteam] O gauge wheel profile
To: "'Small-scale live steam discussions'"
    <[email protected]>
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain;   charset="iso-8859-1"

Mike,
How did you measure that 3 degree taper?
And....I said folks would get upset!
Still, in over 46 years of live steaming, I never saw a track damaged by a
cylindrical wheel tread. Amtrak and every Class 1 road in the US are buying
locomotives with cylindrical treads, and they run the Acela trains at 150
miles per hour.
Keith

> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:sslivesteam-
> [EMAIL PROTECTED] On Behalf Of Mike Chaney
> Sent: Tuesday, November 28, 2006 2:21 PM
> To: Small-scale live steam discussions
> Subject: Re: [SSLiveSteam] O gauge wheel profile
> 
> Keith Taylor wrote:-
> 
> >.... A 3? taper over the tiny tread of an "O" scale wheel is
> > pracitally impossible to see, much less machine.Trying to
> > set over the compound on most lathes to cut a 3? coning
> > of the tread would be tough too, as the graduations on the
> > lathes probably aren't accurate enough to bother.
> 
> What utter nonsense!  My eyes are 67 years old and I can see the taper
quite
> clearly.  I've also spent the last three days machining a batch of wheels
-
> with a three degree taper - and had no difficulty setting the compound
slide
> to within a sensible (about one quarter of a degree) tolerance.
> 
> Mike Chaney
> 
> 
> _______________________________________________
> SSLiveSteam mailing list
> Send messages: [email protected]
> Cancel subscription: http://postfix.45mm.com/mailman/listinfo/sslivesteam
> Rules: http://www.45mm.com/sslivesteam_guide.html



------------------------------

Message: 3
Date: Tue, 28 Nov 2006 21:23:51 +0000
From: Sam <[EMAIL PROTECTED]>
Subject: Re: [SSLiveSteam] O gauge wheel profile
To: Small-scale live steam discussions <[email protected]>
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; charset=us-ascii; format=flowed

Tom Jones wrote:


> Thanks for you info.  I will be looking into it right away.  Also, I am not 
> sure if I am misunderstanding your reply or not, but I was refering to 
> 'L.B.S.C' the man.  In one of his design booklets for an O gauge locomotive, 
> he had his preference for the wheel profile.


Tom

Yes I know that LBSC was 'Curly' Lawrence, an ex LBSC fireman hence the 
pseudonym.  His wheel standards are not NECESSARILY  relevant today.  It 
depends on what track you intend to run on.  Modern Coarse O in UK uses 
a btb of 28mm with a flange root width of 1.5 mm running on track with a 
flangeway of 2.2mm.  Technically the flange depth should be 1.5mm but 
16mm modellers tend to use 2mm as this allows the use of the same 
(GIMRA) wheel profile for 32mm and 45mm gauges while retaining the same 
scale.

Sam E


------------------------------

Message: 4
Date: Tue, 28 Nov 2006 22:04:54 -0000
From: "Mike Chaney" <[EMAIL PROTECTED]>
Subject: Re: [SSLiveSteam] O gauge wheel profile
To: "Small-scale live steam discussions"
    <[email protected]>
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
    reply-type=original

Keith asked:-

> How did you measure that 3 degree taper?

I didn't.  I machined it.

First, I set the compound slide cutting parallel - this took a little time, 
but I only had to do it once, which when I commissioned the lathe.  Then I 
noted the error on the degree scale, which was 1/4 degree clockwise.  When 
setting the slide, I allow for that error assuming that, the machine being 
British made, the graduations had been engraved accurately.

After that, it's all down to eyesight and craftsmanship.

Mike 




------------------------------

Message: 5
Date: Tue, 28 Nov 2006 17:50:25 EST
From: [EMAIL PROTECTED]
Subject: Re: [SSLiveSteam] Wheel taper
To: [email protected]
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; charset="us-ascii"

My understanding of wheel taper (And I may be full of B.S., but this is  what 
I have read) is to allow trains to navigate curves without excessive wheel  
slip. As centrifugal force causes the wheel set to move to the outside of  the 
curve the larger diameter of the tread is contacting the rail  on the larger 
diameter, while the inner wheel is riding on its smaller diameter.  This 
lessens wheel slip and I presume that on 1=1 scale (full size) that  railroads 
set 
minimum curve radius to suit on mainline practice. Look at the  steep taper on 
a Lionel 027 wheel compared to the slight taper on a fine scale  wheel. 
 
I have two kinds of wheels on my 3.5 gauge stuff, one set has each wheel  
with a brass bushing so the wheels can rotate independent of what his brother 
on  

the other end of the axle is doing. The other sets of wheels each wheel is 
press  fitted on the axle so where "Righty" goes, "Lefty" must follow along. 
Next time  I am out at the shop will check and see if either, both or which 
ever 

has taper  and which don't. I have seen no difference in the wheel sets to 
stay on the  track over my 20' radius curves. 
 
Of course on a rod driven locomotive the wheels must be secured to each  axle 
to keep the valve gear working properly. 
 
On my lathe (Sear's Atlas, 12 inch) I have no problem turning the slight 3  
degree taper by setting over the compound to three degrees. Or it could be done 
 by a file on our small wheels with a template to see where we are in the  
process. The wheels must be made to the same diameter, coned or flat within as  
close a limit as you can manage so both sides work the same. What I have done  
and seen recommended is to "rough" turn all your wheels first, then set up to 
 finish each wheel at the same settings on your cross slide and compound. 
When I  have done cast iron wheels I use a carbide bit to dig under the cast 
iron 
"skin"  then when all wheels in the set are rough turned leaving a few thous 
for  finishing change to a HSS tool with the root radius between tread and 
flange  ground in. Then set up a mandrel to take each wheel running true on its 
axis and  take off the final few thous and put in the taper and touch the outer 
rim with a  file to just barely round it over. Also use a file to radius the 
top of the  flange, but I don't think that is too important, but I presume a 
special ground  tool or jig would do that more evenly. 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
http://postfix.45mm.com/pipermail/sslivesteam/attachments/20061128/de2a0d4e/attachment.html


------------------------------

Message: 6
Date: Tue, 28 Nov 2006 18:18:07 -0500
From: "Keith Taylor" <[EMAIL PROTECTED]>
Subject: Re: [SSLiveSteam] Wheel taper
To: "'Small-scale live steam discussions'"
    <[email protected]>
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain;   charset="us-ascii"



> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:sslivesteam-
> [EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED]

> My understanding of wheel taper (And I may be full of B.S., but this is
what
> I have read) is to allow trains to navigate curves without excessive wheel
> slip. As centrifugal force causes the wheel set to move to the outside of
the
> curve the larger diameter of the tread is contacting the rail  on the
larger
> diameter, while the inner wheel is riding on its smaller diameter.  This
> lessens wheel slip and I presume that on 1=1 scale (full size) that
railroads set
> minimum curve radius to suit on mainline practice.

Basically that is true, but the difference in diameter over a 3 degree taper
of a wheel a couple inches in diameter is negligible. And, since most garden
lines use brass or nickel silver rail, that would wear long before the wheel
tread wore! The amount of wheel slip due to now using wheels of constant
diameter wasn't enough for "real railroads" to bother with coned treads
anymore. Class 1 roads use a spiral leading into the curve and
superelevation to eliminate the wheel slip issues.

 Look at the  steep taper on
> a Lionel 027 wheel compared to the slight taper on a fine scale  wheel.

Tinplate is an entirely different application, as they run on tubular rail,
not rail of scale profile. The wheel tread is actually the flange on Lionel
trains.

Basically if you want to put a 3 degree taper on the wheels for accuracy
reasons...fine. But to a beginner building his first steam locomotive
doesn't need to worry if his wheel are EXACTLY a three degree taper. In
fact....if he builds his locomotive with parallel wheel treads, it will run
and track as well as those with a three degree taper. The reason real
railroads have eliminated the coned tread of locomotives is traction. The
contact are is greater when the wheel is contacting the rail across the
whole tread, where as the cone wheel has a very tiny contact area, which
gives you a MUCH better chance to slip! For me....I'll take all the traction
I can get on my models.

Keith

> 



------------------------------

Message: 7
Date: Tue, 28 Nov 2006 18:31:50 -0500
From: "Keith Taylor" <[EMAIL PROTECTED]>
Subject: Re: [SSLiveSteam] Wheel taper
To: "'Small-scale live steam discussions'"
    <[email protected]>
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain;   charset="us-ascii"



Fingers got away from me again. I wrote:
>The reason real railroads have eliminated the coned tread of locomotives is
traction. The
> contact{ are} AREA is greater when the wheel is contacting the rail across
the
> whole tread, where as the cone wheel has a very tiny contact area, which
> gives you a MUCH better chance to slip! For me....I'll take all the
traction
> I can get on my models.

I wrote ARE, when I meant AREA in the above passage.

Keith



------------------------------

Message: 8
Date: Tue, 28 Nov 2006 18:30:51 -0800
From: Jeffrey Williams <[EMAIL PROTECTED]>
Subject: [SSLiveSteam] Dezincification of brass
To: Live steam list <[email protected]>
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed

My "ancient" copy (1961 edition) of the American Society of Metals 
Handbook, Vol 1. describes the dezincification of brass as:

"Copper-zinc alloys containing more than 15% zinc are susceptible to a 
corrosion process called dezincification.  This type of corrosion does 
not occur in aluminum bronze and cupro-nickel, because they do not 
contain zinc.  The initial attack is followed by a secondary reaction in 
which the copper in the corrosion product is redeposited in a porous,  
friable and weak mass on the metal surface.  Corrosion of a similar 
nature continues beneath the primary deposit of copper, resulting in a 
gradual replacement of sound metal by weakened porous copper.   Action 
of this kind, unless arrested, eventually penetrates the metal, 
weakening it structurally and resulting in leakage of liquids or gasses 
through the porous layer....the dezincification usually occurs when 
brasses are in contact with waters that have high oxygen and carbon 
dioxide content....dezincification is not usually a serious problem 
since red brass, admiralty and aluminum brass containing inhibitors of 
dezincification can be used where this form of corrosion has been 
experienced or is anticipated."

This indicates that brass with less than 15% zinc isn't a problem in our 
applications in live steam boilers.  McMaster-Carr 
(http://www.mcmaster.com/) lists a number of bronze and brass shapes for 
pretty reasonable prices that could be easily machined and safely used.


------------------------------

Message: 9
Date: Wed, 29 Nov 2006 06:41:07 -0700
From: "Tom Jones" <[EMAIL PROTECTED]>
Subject: Re: [SSLiveSteam] O gauge wheel profile - Off List
To: [email protected]
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; format=flowed

Sam-

I did misunderstand your first email.  I am sure that with what you have 
given me I will do just fine!

Once again thanks!

-Mitchell


>From: Sam <[EMAIL PROTECTED]>
>Reply-To: Small-scale live steam discussions <[email protected]>
>To: Small-scale live steam discussions <[email protected]>
>Subject: Re: [SSLiveSteam] O gauge wheel profile
>Date: Tue, 28 Nov 2006 21:23:51 +0000
>
>Tom Jones wrote:
>
>
> > Thanks for you info.  I will be looking into it right away.  Also, I am 
>not
> > sure if I am misunderstanding your reply or not, but I was refering to
> > 'L.B.S.C' the man.  In one of his design booklets for an O gauge 
>locomotive,
> > he had his preference for the wheel profile.
>
>
>Tom
>
>Yes I know that LBSC was 'Curly' Lawrence, an ex LBSC fireman hence the
>pseudonym.  His wheel standards are not NECESSARILY  relevant today.  It
>depends on what track you intend to run on.  Modern Coarse O in UK uses
>a btb of 28mm with a flange root width of 1.5 mm running on track with a
>flangeway of 2.2mm.  Technically the flange depth should be 1.5mm but
>16mm modellers tend to use 2mm as this allows the use of the same
>(GIMRA) wheel profile for 32mm and 45mm gauges while retaining the same
>scale.
>
>Sam E
>_______________________________________________
>SSLiveSteam mailing list
>Send messages: [email protected]
>Cancel subscription: http://postfix.45mm.com/mailman/listinfo/sslivesteam
>Rules: http://www.45mm.com/sslivesteam_guide.html
>

_________________________________________________________________
Talk now to your Hotmail contacts with Windows Live Messenger. 
http://clk.atdmt.com/MSN/go/msnnkwme0020000001msn/direct/01/?href=http://get.live.com/messenger/overview



------------------------------

Message: 10
Date: Wed, 29 Nov 2006 13:38:04 -0600
From: "Arthur S. Cohen" <[EMAIL PROTECTED]>
Subject: [SSLiveSteam] (no subject)
To: [email protected]
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; charset="iso-8859-1"

There's been discussion about bronze components not standing up to live ste=
am.  Let me first tell you that all bronzes and brasses are copper alloys. =
 The problem Is the bronze being for brazed on connections are of unknown c=
omposition.  The bronze that should be used is an alloy identified as C92 3=
00.  It's made up of  88 Cu, 6 Sn, 1.5 pb, and 4.5 zn.  All numbers of elem=
ents are %s.  This material is used for high pressure steam connections and=
 valves and should work with the low pressures we use.  I imagine the probl=
em of why some connection fail while others don't is because the brass or b=
ronzes used are not know for their alloy.  They are usually left over small=
 pieces of materials of unknown origin.  I have no idea as to where the cor=
rect material can be obtained in the States.

Arthur---Mexico City
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://postfix.45mm.com/pipermail/sslivesteam/attachments/20061129/866=
4730a/attachment.html


------------------------------

Message: 11
Date: Wed, 29 Nov 2006 13:38:54 -0600
From: "Arthur S. Cohen" <[EMAIL PROTECTED]>
Subject: [SSLiveSteam] Fw:
To: [email protected]
Message-ID: <[EMAIL PROTECTED]>
Content-Type: text/plain; charset="iso-8859-1"


----- Original Message ----- =

From: Arthur S. Cohen =

To: [email protected] =

Sent: Wednesday, November 29, 2006 1:38 PM


There's been discussion about bronze components not standing up to live ste=
am.  Let me first tell you that all bronzes and brasses are copper alloys. =
 The problem Is the bronze being for brazed on connections are of unknown c=
omposition.  The bronze that should be used is an alloy identified as C92 3=
00.  It's made up of  88 Cu, 6 Sn, 1.5 pb, and 4.5 zn.  All numbers of elem=
ents are %s.  This material is used for high pressure steam connections and=
 valves and should work with the low pressures we use.  I imagine the probl=
em of why some connection fail while others don't is because the brass or b=
ronzes used are not know for their alloy.  They are usually left over small=
 pieces of materials of unknown origin.  I have no idea as to where the cor=
rect material can be obtained in the States.

Arthur---Mexico City
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://postfix.45mm.com/pipermail/sslivesteam/attachments/20061129/b3e=
fef23/attachment.html


------------------------------

_______________________________________________
SSLiveSteam mailing list
[email protected]
http://postfix.45mm.com/mailman/listinfo/sslivesteam


End of SSLiveSteam Digest, Vol 15, Issue 17
*******************************************
________________________________________________________________________
Check out the new AOL.  Most comprehensive set of free safety and security 
tools, free access to millions of high-quality videos from across the web, free 
AOL Mail and more.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
http://postfix.45mm.com/pipermail/sslivesteam/attachments/20061129/a44f8536/attachment.html
_______________________________________________
SSLiveSteam mailing list
Send messages: [email protected]
Cancel subscription: http://postfix.45mm.com/mailman/listinfo/sslivesteam
Rules: http://www.45mm.com/sslivesteam_guide.html

Reply via email to