Kevin and Lord Geoff, This is only the Mark 1 model! Doesn't even have wheels fitted! Still some work to do before it rolls under its own steam.
Lord Geoff: can you tell me what the clearance should be between the top of the wick tubes and the boiler or crown sheet in a typical gauge 1 boiler? Right now I think I have to much clearance - perhaps 25mm - between the wick tubes and the bottom of the boiler. Steve On 4/23/07, Kevin Schindler <[EMAIL PROTECTED]> wrote: > > Steve, > Well done! I too have been thinking about this for a few years, but like > Vance, I never did anything about it. I have 4 RH gas fired jobs plus one > Lady Anne Chassis and Boiler Kit in the waiting. That kit project maybe a > good place to apply your new found technology. I would love to have at > least > alcohol fired locomotive. Variety is the spice, don't cha know. > > Please bring your work down to Sacramento this July, I want to give it a > good look. Thanks in advance. > > Cheers, > Kevin > Estancia Fortuna > www.narrowescape.com > > > ----- Original Message ----- > From: "Steve Shyvers" <[EMAIL PROTECTED]> > To: "Small-scale live steam discussions" <[email protected]> > Sent: Monday, April 23, 2007 7:23 AM > Subject: [SSLiveSteam] Alcohol Firing a Standard Roundhouse Butane Boiler > > > > Succeeded yesterday with a successful experiment to alcohol-fire a > > Roundhouse single-flue butane boiler. It was a bench test using a simple > > add-on firebox and a two-wick burner. No fancy calculations involved. > Most > > dimensions guesstimated. This first test with little more than a mock-up > > of > > an external firebox blew the safety after not too many minutes and > simply > > amazed me. My last two loco projects were not brilliant in the firing > > department until after a lot of experimentation and rebuilding. > > > > The firebox was fabricated from olive oil can sheet metal and > > silver-brazed. > > It fits under the aft 50mm of the boiler, and an extension wraps up > around > > the back of the boiler to connect the firebox to the existing single > flue. > > The wicks are positioned below the boiler's aft end, which makes the > > boiler > > a C-type. Right now the boiler wrapper is holding the firebox onto the > > boiler by means of flanges along the upper edges of the firebox that are > > slipped under the wrapper before it's cinched tight. Properly it should > > have > > a more secure method of mounting, and there should be some sort of > sealant > > to prevent leaks that might interfere with the draft. > > > > The burner's two wick holders are each 11mm inside dia and 20mm deep > > inside > > (fabricated from std copper pipe and pipe caps.) The wick holders are > > spaced > > 20mm apart. I did a proper job and silver-brazed the burner and fuel > sump > > assemblies. The idea was that if the experiment were a success, then > > these > > parts would be good for the final version and not need to be made again. > > Otherwise they could be re-used in some other project. > > > > To create a draft for the fire I rigged a blast nozzle in the smokebox > > (standard Roundhouse) and fed it with an air jet from a garden sprayer > > that's been setup as a low-pressure compressed air supply. The blast > > nozzle > > was positioned below the narrowest part of the stack a distance equal to > > the > > three times the stack's narrowest inside diameter. The nozzle height is > > adjustable, and some experimentation must be done for the optimal blast > > nozzle oriface size and position. Blast nozzle (a piece of K&S 1/8 inch > > brass tubing) oriface was 3/32 inch for the test. Probably bigger than > > necessary. > > > > In a few days I will try to post a photo or two of the bench test setup, > > the > > burner assembly, and the firebox. > > > > Steve > > Duke of Spam > > -------------- next part -------------- > > An HTML attachment was scrubbed... > > URL: > > > http://postfix.45mm.com/pipermail/sslivesteam/attachments/20070423/0d70843a/attachment.html > > _______________________________________________ > > SSLiveSteam mailing list > > Send messages: [email protected] > > Cancel subscription: > http://postfix.45mm.com/mailman/listinfo/sslivesteam > > Rules: http://www.45mm.com/sslivesteam_guide.html > > > > _______________________________________________ > SSLiveSteam mailing list > Send messages: [email protected] > Cancel subscription: http://postfix.45mm.com/mailman/listinfo/sslivesteam > Rules: http://www.45mm.com/sslivesteam_guide.html > > -------------- next part -------------- An HTML attachment was scrubbed... URL: http://postfix.45mm.com/pipermail/sslivesteam/attachments/20070423/b3964519/attachment.html _______________________________________________ SSLiveSteam mailing list Send messages: [email protected] Cancel subscription: http://postfix.45mm.com/mailman/listinfo/sslivesteam Rules: http://www.45mm.com/sslivesteam_guide.html
