Thanks for the help, I was able to fix the spawning by modifying the intervals to be smaller so the car spawning was not as inconsistent. I have a couple other questions. Is it possible to spawn pedestrians similarly to cars with calibrators? I tried to do it but it doesn't seem to work. Also, is there a way to set more than one route in a calibrator?
Thanks again, Kaitlyn On Tue, Apr 16, 2024 at 3:27 AM Mirko Barthauer <m.bartha...@t-online.de> wrote: > Hi Kaitlyn, > > > > you have used the Calibrator together with routeProbe elements. I didn't > notice that when first scrolling across your XML. Apparently the route > distribution created by routeProbe is preferred in comparison to the flow > route attribute. When the route distribution is not available (no vehicles > passed in the last interval), then it seems no vehicles are generated > neither. > > > > As you added a route attribute to the flow definition, it looks like you > don't want the routeProbe...? So just remove the routeProbe attribute from > the Calibrator. > > > > Best regards > > Mirko > > > > > > > > > > > > -----Original-Nachricht----- > > Betreff: Re: [sumo-user] Calibrators Not Spawning > > Datum: 2024-04-13T05:28:52+0200 > > Von: "Kaitlyn Liu" <liu.kaitl...@gmail.com> > > An: "Mirko Barthauer" <m.bartha...@t-online.de> > > > > > > > Attached are the files for my simulation as well as the basic TraCI script > stepping through the simulation. I also noticed other than the problem with > the delay over 3600, the cars don't start spawning until around 200 steps > into the simulation and each of the calibrators start spawning at different > times. I'm not sure how to fix this issue either because I want the cars to > start spawning immediately and the flow begins at 0 for all of the > calibrators. > > Thank you again! > Kaitlyn > > On Fri, Apr 12, 2024 at 5:30 AM Mirko Barthauer <m.bartha...@t-online.de> > wrote: > >> Hi Kaitlyn, >> >> >> >> I can't reproduce this with our test examples. Could you please post at >> least your updated calibrator definitions (or better even attach a minimal >> failing scenario to run in sumo)? >> >> >> >> Best regards >> >> Mirko >> >> >> >> >> >> >> >> >> >> -----Original-Nachricht----- >> >> Betreff: Re: [sumo-user] Calibrators Not Spawning >> >> Datum: 2024-04-11T17:48:22+0200 >> >> Von: "Kaitlyn Liu" <liu.kaitl...@gmail.com> >> >> An: "Mirko Barthauer" <m.bartha...@t-online.de> >> >> >> >> >> >> >> >> Just realized I didn’t reply to the mailing list, so resending my >> previous message. >> >> Thanks for the response! I added the flow end attribute and cars are >> spawning now, however I can't seem to extend the end past 3600 seconds. >> Whenever I try to do so, the calibrators won't spawn cars. What should I do >> if I want to make the simulation last for longer than an hour? >> >> Thanks, >> Kaitlyn >> >> On Apr 10, 2024, at 5:10 PM, Kaitlyn Liu <liu.kaitl...@gmail.com> wrote: >> >> Hi Mirko, >> >> Thanks for the response. I added the flow end attribute and cars are >> spawning now, however I can't seem to extend the end past 3600 seconds. >> Whenever I try to do so, the calibrators won't spawn cars. What should I do >> if I want to make the simulation last for longer than an hour? >> >> Thanks, >> Kaitlyn >> >> On Wed, Apr 10, 2024 at 12:36 PM Mirko Barthauer <m.bartha...@t-online.de> >> wrote: >> >>> Hi Kaitlyn, >>> >>> >>> >>> what happens if you add the flow end attribute? Judging from the source >>> code, I think this can be a problem because the flow duration is undefined >>> / set to 0. >>> >>> >>> >>> Best regards >>> >>> Mirko >>> >>> >>> >>> >>> >>> >>> >>> -----Original-Nachricht----- >>> >>> Betreff: [sumo-user] Calibrators Not Spawning >>> >>> Datum: 2024-04-10T17:50:37+0200 >>> >>> Von: "Kaitlyn Liu via sumo-user" <sumo-user@eclipse.org> >>> >>> An: "sumo-user@eclipse.org" <sumo-user@eclipse.org> >>> >>> >>> >>> >>> >>> >>> Hello, >>> >>> I am currently trying to insert calibrators into my simulation but the >>> calibrators do not seem to be spawning in with both a manual route (ca_3) >>> or a route probe (ca_0-2). I have the following additional file: >>> >>> >>>> <additional xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"; >>>> xsi:noNamespaceSchemaLocation=" >>>> http://sumo.dlr.de/xsd/additional_file.xsd";> >>>> <!-- RouteProbes --> >>>> <vType id="spawned_car" vClass="passenger" color="1,1,1"/> >>>> <routeProbe id="rp_0" begin="0.00" period="20.00" edge="28727103#0" >>>> file="rp_0.xml"/> >>>> <routeProbe id="rp_1" begin="0.00" period="20.00" >>>> edge="625479007#6" file="rp_1.xml"/> >>>> <routeProbe id="rp_2" begin="0.00" period="20.00" >>>> edge="-292851770#0" file="rp_2.xml"/> >>>> <routeProbe id="rp_3" begin="0.00" period="20.00" >>>> edge="-966308107#4" file="rp_3.xml"/> >>>> >>>> <route id="r_0" edges="-966308107#4 -28727096#5 -28727096#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 926031003#0 11956345 >>>> 926031004#0 -11734068#2" color="red"/> >>>> <route id="r_1" edges="-966308107#4 11826990#0 11826990#2 >>>> 11826990#3 265895120#0 28727103#0 28727103#4 11834237#0 11834237#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 11737884#0" color="green"/> >>>> <route id="r_2" edges="-625851681#2 -28727096#5 -28727096#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 11737884#0" color="green"/> >>>> <route id="r_3" edges="-966308107#4 -28727096#5 -28727096#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 11737884#0"/> >>>> <route id="r_4" edges="-625851681#2 -28727096#5 -28727096#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 926031003#0 11956345 >>>> 926031004#0 -11734068#2" color="blue"/> >>>> <route id="r_5" edges="-625851681#2 11826990#0 11826990#2 >>>> 11826990#3 265895120#0 28727103#0 28727103#4 11834237#0 11834237#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 11737884#0" color="blue"/> >>>> <route id="r_6" edges="-625851681#2 11826990#0 11826990#2 >>>> 11826990#3 265895120#0 -320455187#3 -24864540#7 -335532208#1 335532207#0 >>>> 11729090#0 11729090#1 335532206 54964356#0" color="blue"/> >>>> <route id="r_7" edges="-966308107#4 11826990#0 11826990#2 >>>> 11826990#3 265895120#0 -320455187#3 -24864540#7 -335532208#1 335532207#0 >>>> 11729090#0 11729090#1 335532206 54964356#0" color="blue"/> >>>> <route id="r_8" edges="-11826990#1 11960711#0 -294921088#6 >>>> 1121515071" color="blue"/> >>>> <route id="r_9" edges="-11826990#1 625851681#0 625361998#0 >>>> 625361998#1 625361998#4 625361998#5 292851770#0 292851770#1 292851770#7" >>>> color="blue"/> >>>> <route id="r_10" edges="-11826990#1 -28727096#5 -28727096#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 11737884#0" color="blue"/> >>>> <route id="r_11" edges="-11826990#1 -28727096#5 -28727096#1 >>>> 625479007#0 625479007#1 625479007#3 625479007#6 926031003#0 11956345 >>>> 926031004#0 -11734068#2" color="blue"/> >>>> <route id="r_12" edges="28727096#2 11826990#0 11826990#2 11826990#3 >>>> 265895120#0 -320455187#3 -24864540#7 -335532208#1 335532207#0 11729090#0 >>>> 11729090#1 335532206 54964356#0"/> >>>> <route id="r_13" edges="28727096#2 625851681#0 625361998#0 >>>> 625361998#1 625361998#4 625361998#5 292851770#0 292851770#1 292851770#7"/> >>>> <route id="r_14" edges="28727096#2 11960711#0 -294921088#6 >>>> -294921088#4 320948882#0"/> >>>> <route id="r_15" edges="28727096#2 625851681#0 625361998#0 >>>> 625361998#1 625361998#4 625361998#5 11837579#0 11837579#3 335532207#0 >>>> 11729090#0 11729090#1 335532206 54964356#0"/> >>>> >>>> <!-- Calibrators --> >>>> <calibrator id="ca_1" edge="625479007#6" pos="0.00" >>>> routeProbe="rp_1"> >>>> <flow begin="0.00" departPos="free" departSpeed="max" >>>> speed="27.80" vehsPerHour="600.00"/> >>>> </calibrator> >>>> <calibrator id="ca_0" edge="28727103#0" pos="0.00" >>>> routeProbe="rp_0"> >>>> <flow begin="0.00" departPos="free" departSpeed="max" >>>> speed="27.80" vehsPerHour="1000.00"/> >>>> </calibrator> >>>> <calibrator id="ca_2" edge="-292851770#0" pos="0.00" >>>> routeProbe="rp_2"> >>>> <flow begin="0.00" departPos="free" departSpeed="max" >>>> speed="27.80" vehsPerHour="600.00"/> >>>> </calibrator> >>>> <calibrator id="ca_3" edge="-966308107#4" pos="0.00" >>>> output="ca_3.xml"> >>>> <flow begin="0.00" departPos="free" departSpeed="max" >>>> speed="27.80" route="r_0" vehsPerHour="100.00" period="5"/> >>>> </calibrator> >>>> >>>> <!-- Detectors --> >>>> <laneAreaDetector id="0" lane="28727096#2_0" pos="70.00" >>>> length="49.00" tl="GS_105097632" file="LAD_output"/> >>>> <laneAreaDetector id="1" lane="28727096#2_1" pos="70.00" >>>> length="49.00" tl="GS_105097632" file="LAD_output"/> >>>> <laneAreaDetector id="2" lane="-625851681#2_0" pos="80.00" >>>> length="49.00" tl="GS_105097632" file="LAD_output"/> >>>> <laneAreaDetector id="3" lane="-625851681#2_1" pos="80.00" >>>> length="49.00" tl="GS_105097632" file="LAD_output"/> >>>> <laneAreaDetector id="4" lane="-966308107#4_0" pos="285.00" >>>> length="49.00" tl="GS_105097632" file="LAD_output"/> >>>> <laneAreaDetector id="5" lane="-11826990#1_0" pos="5.00" >>>> length="40.00" tl="GS_105097632" file="LAD_output"/> >>>> </additional> >>> >>> >>> These are my configs for traci: >>> >>>> traci.start( >>> >>> [ >>> sumoBinary, >>> '--net-file', 'simulation/network.net.xml', >>> '--route-files', 'simulation/passenger.trips.xml', >>> '--delay', '1000', >>> '--gui-settings-file', 'simulation/view.xml', >>> '--additional-files', 'simulation/additional.add.xml', >>> '--max-depart-delay', '20', >>> '--extrapolate-departpos', >>> '--start' >>> ]) >>> >>> I was wondering if anyone has any idea what could be going wrong. >>> >>> Thanks, >>> Kaitlyn >>> >> >> > > >
_______________________________________________ sumo-user mailing list sumo-user@eclipse.org To unsubscribe from this list, visit https://www.eclipse.org/mailman/listinfo/sumo-user
