Hi, somehow your ubuntu sumo was compiled without proj support. Did you compile it by yourself? And if so could you send the config.log? If not, you need to "complain" with the origin of your package.
Best regards, Michael 2013/10/28 Wilmer Arellano <[email protected]>: > Thank you Michael, > > I think you are right and there is a problem with proj. > I have installed libproj0 4.7.0-2, the attachment shows other versions of > proj. available in my system. > Do I need to install a different version of proj.? If so, do I need to redo > the whole installation? I am not expert with Linux, help is highly > appreciated. > > Bellow you can see the response on each operating system. > > Regards, > > Wilmer Arellano > > Under Ubuntu I get: > > Projection Options: > --simple-projection Uses a simple method for projection > --proj.scale INT Number of places to shift decimal > point > to right in geo-coordinates > > While under Windows I get: > > Projection Options: > --simple-projection Uses a simple method for projection > --proj.scale INT Number of places to shift decimal > point > to right in geo-coordinates > --proj.utm Determine the UTM zone (for a > universal > transversal mercator projection > based on > > the WGS84 ellipsoid) > --proj.dhdn Determine the DHDN zone (for a > transversal mercator projection > based on > > the bessel ellipsoid) > --proj STR Uses STR as proj.4 definition for > projection > --proj.inverse Inverses projection > --proj.plain-geo Write geo coordinates in plain-xml > > I t > > > On Tue, Oct 22, 2013 at 4:33 PM, Michael Behrisch > <[email protected]> wrote: >> >> Hi, >> it's hard to say from a distance. Try to call netconvert --help and if >> you see a lot of projection options including things like --proj.utm, >> then coordinate conversion using proj is available. If it is not on >> one platform, then results should differ considerably. If proj is >> available on both platforms it could be that the distance is very >> close to 0.1m (which is the threshold) and it is a mere floating point >> issue. >> >> Best regards, >> Michael >> >> 2013/10/21 Wilmer Arellano <[email protected]>: >> > Thank you Michael, >> > >> > This same example runs fine under windows. Is there something missing in >> > my >> > Ubuntu installation? >> > >> > Regards, >> > >> > Wilmer >> > >> > >> > On Sat, Oct 19, 2013 at 3:46 PM, Michael Behrisch >> > <[email protected]> wrote: >> >> >> >> Hi, >> >> the start and the end nodes are too close to each other. You could try >> >> removing geometry nodes (not sure if it helps though) or if you think >> >> you can safely leave out the edge simply use --ignore-errors. >> >> >> >> >> >> Best regards, >> >> Michael >> >> >> >> 2013/10/13 Wilmer Arellano <[email protected]>: >> >> > Hello, >> >> > >> >> > My problem is more general than what I originally posted. >> >> > >> >> > When importing OSM maps I am having problems with NETCONVERT. I >> >> > receive >> >> > many: >> >> > >> >> > *Warning: Could not use edge geometry for internal lane, node* >> >> > errors. >> >> > >> >> > These errors happen with any NETCONVERT options, like the example >> >> > bellow. >> >> > >> >> > netconvert --remove-edges.isolated --type-files I-95.typ.xml >> >> > --osm-files >> >> > I-95.osm --plain-output-prefix SF1 >> >> > >> >> > If I later try a command similar to: >> >> > >> >> > *netconvert -c I-95.netccfg --type-files I-95.typ.xml -n SF1.nod.xml >> >> > -e >> >> > SF1.edg.xml --o SF1.net.xm* >> >> > >> >> > NETCONVERT quits on error with a log similar to: >> >> > * >> >> > Error: Edge's '98957963#3' from- and to-node are at the same >> >> > position. >> >> > Error: Edge's '98957963#5' from- and to-node are at the same >> >> > position. >> >> > Error: Edge's '98957963#6' from- and to-node are at the same >> >> > position. >> >> > Error: Edge's '98957966#1' from- and to-node are at the same >> >> > position. >> >> > done. >> >> > Import done: >> >> > 2725 nodes loaded. >> >> > 35 types loaded. >> >> > 6487 edges loaded. >> >> > Quitting (on error). >> >> > * >> >> > Could you please give some orientation on what to fix? >> >> > >> >> > Thank you, >> >> > >> >> > Wilmer Arellano >> >> > >> >> > >> >> > On Thu, Oct 10, 2013 at 12:48 PM, Jakob Erdmann >> >> > <[email protected]>wrote: >> >> > >> >> >> Hello, >> >> >> for me version 0.17.1 is correctly building the network according to >> >> >> your parameters and input files on ubuntu. >> >> >> Anyway, to obtain revision [14830] you need to check out the source >> >> >> from our subversion repository and build it yourself (see >> >> >> http://sumo-sim.org/wiki/Installing/Linux_Build). >> >> >> The ubuntu repositories are a bit behind at the moment (and only >> >> >> contain official releases anyway) >> >> >> regards, >> >> >> Jakob >> >> >> >> >> >> >> >> >> 2013/10/10 Wilmer Arellano <[email protected]>: >> >> >> > Thank you Jakob, >> >> >> > >> >> >> > I am using SUMO 0.17.1. Installed several months ago. >> >> >> > >> >> >> > Could you please help wit the questions bellow? >> >> >> > >> >> >> > Do I need to reinstall SUMO using sudo add-apt-repository >> >> >> ppa:sumo/stable, >> >> >> > sudo apt-get install sumo sumo-tools sumo-doc? >> >> >> > or just copy and paste NETCONVERT? >> >> >> > I was not able to find revision [14830] Could you please send a >> >> >> > link? >> >> >> > >> >> >> > Regards, >> >> >> > >> >> >> > Wilmer Arellano >> >> >> > >> >> >> > >> >> >> > >> >> >> > On Thu, Oct 10, 2013 at 3:21 AM, Jakob Erdmann < >> >> >> [email protected]> >> >> >> > wrote: >> >> >> >> >> >> >> >> Hello Wilmer, >> >> >> >> I suppose on Ubuntu you were using the very latest svn revision. >> >> >> >> This >> >> >> >> contains a change for reducing the output regarding OSM compound >> >> >> >> edge >> >> >> >> types. >> >> >> >> As a side effect this revision also introduces new edge types >> >> >> >> which >> >> >> >> were not covered by your SF1.typ.xml file causing an import >> >> >> >> error. >> >> >> >> (i.e. there was a new type "highway.primary|railway.abandoned") >> >> >> >> I have rethought the issue and patched netconvert to prevent >> >> >> >> unnecessary creation of new type names (the compound >> >> >> >> "railway.abandoned" is not used anyway so the type will be called >> >> >> >> "highway.primary" as before. >> >> >> >> In conclusion: using revision [14830] your import should succeed. >> >> >> >> >> >> >> >> regards, >> >> >> >> Jakob >> >> >> >> >> >> >> >> 2013/10/10 Wilmer Arellano <[email protected]>: >> >> >> >> > I am trying to import an OSM map both under Windows 7 and >> >> >> >> > Ubuntu >> >> >> 12.10. >> >> >> >> > >> >> >> >> > Using the exact same commands the import fails on Ubunto, but >> >> >> >> > works >> >> >> with >> >> >> >> > no >> >> >> >> > problem under Windows . The commands used are: >> >> >> >> > >> >> >> >> > >> >> >> >> > 1. osmGet.py --prefix SF1 --bbox "26.0937883, -80.1782227, >> >> >> >> > 26.7578734, >> >> >> >> > -80.0422668" >> >> >> >> > 2. netconvert --remove-edges.by-type "highway.secondary, >> >> >> >> > highway.secondary_link, highway.tertiary, >> >> >> >> > highway.tertiary_link, >> >> >> >> > highway.unclassified, highway.residential, highway.road, >> >> >> >> > highway.living_street, highway.pedestrian, highway.service, >> >> >> >> > highway.bus_guideway, highway.track, highway.services, >> >> >> >> > highway.unsurfaced, >> >> >> >> > highway.footway, highway.path, highway.bridleway, >> >> >> >> > highway.cycleway, >> >> >> >> > highway.step, highway.steps, highway.stairs, >> >> >> >> > railway.rail,railway.tram, >> >> >> >> > railway.light_rail, railway.subway, railway.preserved, >> >> >> >> > railway.narrow_gauge, railway.monorail, railway.funicular" >> >> >> >> > --remove-edges.isolated --type-files SF1.typ.xml --osm-files >> >> >> >> > SF1_bbox.osm.xml --plain-output-prefix SF1 >> >> >> >> > 3. netconvert -c SF1.netccfg --type-files SF1.typ.xml -n >> >> >> SF1.nod.xml >> >> >> >> > -e >> >> >> >> > SF1.edg.xml --o SF1.net.xm >> >> >> >> > >> >> >> >> > >> >> >> >> > I am attaching files SF1.netccfg and SF1.typ.xml >> >> >> >> > >> >> >> >> > The second command produces different log, last warnings >> >> >> >> > indicate: >> >> >> >> > "Could >> >> >> >> > not use edge geometry for internal lane, node 'xxxxxxx'" >> >> >> >> > >> >> >> >> > Am I doing something wrong? >> >> >> >> > >> >> >> >> > Thank you, >> >> >> >> > >> >> >> >> > Wilmer >> >> >> >> > >> >> >> >> > >> >> >> >> > >> >> >> >> >> >> >> >> >> ------------------------------------------------------------------------------ >> >> >> >> > October Webinars: Code for Performance >> >> >> >> > Free Intel webinars can help you accelerate application >> >> >> >> > performance. >> >> >> >> > Explore tips for MPI, OpenMP, advanced profiling, and more. Get >> >> >> >> > the >> >> >> most >> >> >> >> > from >> >> >> >> > the latest Intel processors and coprocessors. See abstracts and >> >> >> register >> >> >> >> > > >> >> >> >> > >> >> >> >> > >> >> >> >> >> >> >> >> >> http://pubads.g.doubleclick.net/gampad/clk?id=60134071&iu=/4140/ostg.clktrk >> >> >> >> > _______________________________________________ >> >> >> >> > sumo-user mailing list >> >> >> >> > [email protected] >> >> >> >> > https://lists.sourceforge.net/lists/listinfo/sumo-user >> >> >> >> > >> >> >> > >> >> >> > >> >> >> >> >> > >> >> > >> >> > ------------------------------------------------------------------------------ >> >> > October Webinars: Code for Performance >> >> > Free Intel webinars can help you accelerate application performance. >> >> > Explore tips for MPI, OpenMP, advanced profiling, and more. Get the >> >> > most >> >> > from >> >> > the latest Intel processors and coprocessors. See abstracts and >> >> > register >> >> > > >> >> > >> >> > >> >> > http://pubads.g.doubleclick.net/gampad/clk?id=60134071&iu=/4140/ostg.clktrk >> >> > _______________________________________________ >> >> > sumo-user mailing list >> >> > [email protected] >> >> > https://lists.sourceforge.net/lists/listinfo/sumo-user >> > >> > > > ------------------------------------------------------------------------------ October Webinars: Code for Performance Free Intel webinars can help you accelerate application performance. Explore tips for MPI, OpenMP, advanced profiling, and more. Get the most from the latest Intel processors and coprocessors. See abstracts and register > http://pubads.g.doubleclick.net/gampad/clk?id=60135991&iu=/4140/ostg.clktrk _______________________________________________ sumo-user mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/sumo-user
