OK I have tried 3 CDROMS and 3 floppy drives with no luck. All the CDROMS and Floppy drives are good with 1 new of each in that mix. I have tried a blank floppy and then tried a floppy with a working config file. I replaced both the floppy and CDROM cables with no luck :(
I also tried 74.4, 80.0, 80.4, 85.0 and 85.2 versions with the same error every time. Thanks, Mike -----Original Message----- From: Scott Ullrich [mailto:[EMAIL PROTECTED] Sent: Tuesday, September 27, 2005 6:23 PM To: support@pfsense.com Subject: Re: [pfSense Support] CDROM Version Install Yes, s0ren changed tha ATAPI CDRom code recently. :/ Scott On 9/27/05, Fleming, John (ZeroChaos) <[EMAIL PROTECTED]> wrote: > "If you get a chance try a default install (just for testing) of FreeBSD > Beta 5 (or whatever the latest beta of 6.0 is) and see if you get the > same issues." > :) > > -----Original Message----- > From: Holger Bauer [mailto:[EMAIL PROTECTED] > Sent: Tuesday, September 27, 2005 5:15 PM > To: support@pfsense.com > Subject: AW: [pfSense Support] CDROM Version Install > > I'm seeing this problem since 0.85.2. the same cd-rom reader was working ever since pfsense 0.20 for me :-/ > > Holger > > -----Ursprüngliche Nachricht----- > Von: Fleming, John (ZeroChaos) [mailto:[EMAIL PROTECTED] > Gesendet: Mittwoch, 28. September 2005 00:12 > An: support@pfsense.com > Betreff: RE: [pfSense Support] CDROM Version Install > > > FreeBSD is having love issue (see no) with your cdrom. It could be.. > 1. bad cdrom drive > 2. bad cdrom > 3. bad cable > 4. sucky IDE chipset. > 5. FreeBSD bug. > > If you get a chance try a default install (just for testing) of FreeBSD > Beta 5 (or whatever the lastest beta of 6.0 is) and see if you get the > same issues. > -----Original Message----- > From: Mike [mailto:[EMAIL PROTECTED] > Sent: Tuesday, September 27, 2005 5:06 PM > To: support@pfsense.com > Subject: [pfSense Support] CDROM Version Install > Importance: High > > Hi Guys, > I am pulling my hair out trying to figure this out. > I have PFSense now running on several boxes in different locations. > > I am building a new firewall for a client and during the install I am > getting the following error on versions 80.0, 80.4, 85.0 and 85.2. > > The error is as follows: > > Acd0: Failure_Read_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 > error=4<aborted> > > Letting this run it finally comes up asking if I want to setup my vlan > now. > I go through the setup fine add a few rules and reboot and the process > starts over. > > Please help as I am bald enough now and the ole lady hates when I start > pulling her hair out of her head. > > Thanks in Advance, > > Mike > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > > ____________ > Virus checked by G DATA AntiVirusKit > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]