Marc A. Volovic wrote:
> Added to table.
>
> Quoth Gil Freund:
>
>
>>Looks Ok. I tried (all Atheros 5212):
>>Make 0.88 0.90 0.93
>>==================== ======= ======= =======
>>Askey Problem OK OK
>>Gigabyte GN-WIAG02 Problem Problem OK
Spoken too soon....
See attached dmesg output. This is on a 0.90 upgraded to 0.93.
Seems OK on a full 0.93 install.
>>Philips (IBM OEM) OK OK OK
>
> TP-Link TL-WN660G Problem Problem OK
> TP-Link TL-WN560G Problem Problem OK
>
P.S. Hardware is PC-Engine Wrap
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RC1 #1: Sun Oct 30 20:41:50 UTC 2005
[EMAIL PROTECTED]:/usr/obj/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.65-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 134217728 (128 MB)
avail memory = 121913344 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.16.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413, DFS)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: <network, ethernet> at device 13.0 (no driver attached)
pci0: <simple comms, UART> at device 13.1 (no driver attached)
pci0: <old, non-VGA display device> at device 13.2 (no driver attached)
pci0: <old, non-VGA display device> at device 13.3 (no driver attached)
pci0: <old, non-VGA display device> at device 13.4 (no driver attached)
pci0: <old, non-VGA display device> at device 13.5 (no driver attached)
pci0: <old, non-VGA display device> at device 13.6 (no driver attached)
pci0: <old, non-VGA display device> at device 13.7 (no driver attached)
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x1400-0x14ff mem
0x80080000-0x80080fff irq 10 at device 14.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:02:c4:98
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0x1800-0x18ff mem
0x800c0000-0x800c0fff irq 9 at device 15.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:0d:b9:02:c4:99
sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0x1c00-0x1cff mem
0x80100000-0x80100fff irq 11 at device 16.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:0d:b9:02:c4:9a
Geode GPIO@ = f400
Geode PC Engines WRAP.1C/1D/1E v1.tinyBIOS V1.4a (C)1997-2005
isab0: <PCI-ISA bridge> port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 18.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <multimedia, audio> at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge> at device 18.5 (no driver attached)
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xe0000-0xe7fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 80<clock_battery>
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: FAILURE - SETFEATURES SET TRANSFER MODE status=51<READY,DSC,ERROR>
error=4<ABORTED>
ad0: 244MB <Hitachi XX.V.3.4.0.0 Rev 0.00> at ata0-master BIOSPIO
Trying to mount root from ufs:/dev/ad0a
sis0: link state changed to UP
sis1: link state changed to DOWN
sis2: link state changed to DOWN
bridge0: Ethernet address: ac:de:48:e7:86:13
pflog0: promiscuous mode enabled
pfSense#
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
