Until now it behaviour did not change ... Using: 1.0.1-SNAPSHOT-02-27-2007 built on Tue Mar 6 09:35:38 EST 2007
# ipfw show 00030 22320 9418077 skipto 50000 ip from any to any in via fxp0 keep-state 00030 4883 2515916 skipto 50000 ip from any to any in via fxp2 keep-state 00030 0 0 skipto 50000 ip from any to any in via fxp1 keep-state 00030 0 0 skipto 50000 ip from any to any in via fxp3 keep-state 00050 4 524 skipto 29900 ip from any to any MAC 00:0e:35:6c:bf:d7 any keep-state 00050 0 0 skipto 29900 ip from any to any MAC any 00:0e:35:6c:bf:d7 keep-state 00050 0 0 skipto 29900 ip from any to any MAC 00:14:6c:6c:f4:58 any keep-state 00050 0 0 skipto 29900 ip from any to any MAC any 00:14:6c:6c:f4:58 keep-state 00050 0 0 skipto 29900 ip from any to any MAC 00:18:de:a0:f7:2e any keep-state 00050 0 0 skipto 29900 ip from any to any MAC any 00:18:de:a0:f7:2e keep-state 00050 0 0 skipto 29900 ip from any to any MAC 00:80:5a:35:4f:7b any keep-state 00050 0 0 skipto 29900 ip from any to any MAC any 00:80:5a:35:4f:7b keep-state 01000 16617 3892662 skipto 50000 ip from any to any not layer2 not via ath0 01001 8152 1184059 allow ip from any to any layer2 not via ath0 01100 14 392 allow ip from any to any layer2 mac-type 0x0806 01100 8 934 allow ip from any to any layer2 mac-type 0x888e 01100 0 0 allow ip from any to any layer2 mac-type 0x88c7 01100 0 0 allow ip from any to any layer2 mac-type 0x8863 01100 0 0 allow ip from any to any layer2 mac-type 0x8864 01100 0 0 allow ip from any to any layer2 mac-type 0x8863 01100 0 0 allow ip from any to any layer2 mac-type 0x8864 01100 0 0 allow ip from any to any layer2 mac-type 0x888e 01101 1 6 deny ip from any to any layer2 not mac-type 0x0800 01102 395 53712 skipto 20000 ip from any to any layer2 01200 2 682 allow udp from any 68 to 255.255.255.255 dst-port 67 in 01201 0 0 allow udp from any 68 to 10.100.101.1 dst-port 67 in 01202 0 0 allow udp from 10.100.101.1 67 to any dst-port 68 out 01203 0 0 allow icmp from 10.100.101.1 to any out icmptypes 8 01204 0 0 allow icmp from any to 10.100.101.1 in icmptypes 0 01300 0 0 allow udp from any to 10.100.101.1 dst-port 53 in 01301 0 0 allow udp from 10.100.101.1 53 to any out 01302 0 0 allow tcp from any to 10.100.101.1 dst-port 8000 in 01303 0 0 allow tcp from 10.100.101.1 8000 to any out 19902 0 0 fwd 127.0.0.1,8000 tcp from any to any dst-port 80 in 19903 0 0 allow tcp from any 80 to any out 19904 391 52372 deny ip from any to any 29900 399 54236 allow ip from any to any layer2 65535 43828 15827315 allow ip from any to any -----Ursprüngliche Nachricht----- Von: Scott Ullrich [mailto:[EMAIL PROTECTED] Gesendet: Dienstag, 6. März 2007 01:17 An: support@pfsense.com Betreff: Re: [pfSense Support] Captive Portal I found a potential issue. Please test a snapshot around two hours from now. Scott On 3/5/07, Scott Ullrich <[EMAIL PROTECTED]> wrote: > On 3/5/07, Fuchs, Martin <[EMAIL PROTECTED]> wrote: > > Hi, Scott ! > > > > Fresh install shows the following, but does not work also :-( > [snip] > > 01100 0 0 allow ip from any to any layer2 mac-type 0x888e > > I don't see the traffic counter increasing on this test. Did you > actually test login again? The prior output shows the counter at 4. > > Scott > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
