Hello
Searched through the list and found many posts on VLAN. To my knowledge
I have done what I think is correct but packages wont go through. I can
see in the pfSense logs that packages do get in on the right VLAN
interface but that's about it.
bge0 is WAN
bge1 is LAN
I have defined two VLANs (201 and 202) and added them as interfaces
VLAN201 10.150.1.1
VLAN202 10.150.2.1
! This is where bge0 is connected
interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport mode trunk
no ip address
!
! attached to machine b (10.150.2.10)
interface FastEthernet0/17
switchport access vlan 202
no ip address
!
! attached to machine a (10.150.1.10)
interface FastEthernet0/31
switchport access vlan 201
no ip address
I have added an allow anything anywhere rule on each VLAN interface (and
WAN too)
When I ping the firewall from machines a or b the log say something on
the lines of
Oct 14 18:12:42 VLAN202 10.150.2.10 10.150.2.1 ICMP
But no replies come back. I cannot ping the machines from pfSense either.
So packages gets tagged and understood TO pfSense but something error
happens the other way.
What I do get on machine A and B is some Cisco packets:
Capturing on eth1
0.000000 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
1.999793 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
2.791435 Cisco_e1:b1:8d -> Cisco_e1:b1:8d LOOP Reply
3.999626 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
5.999456 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
7.999297 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
9.999141 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
11.998963 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
12.790606 Cisco_e1:b1:8d -> Cisco_e1:b1:8d LOOP Reply
13.998792 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
15.998627 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
17.166677 Cisco_e1:b1:8d -> CDP/VTP/DTP/PAgP/UDLD CDP Device ID:
Switch Port ID: FastEthernet0/17
17.998475 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
19.998302 Cisco_e1:b1:8d -> Spanning-tree-(for-bridges)_00 STP Conf.
Root = 32970/00:09:b7:e1:b1:80 Cost = 0 Port = 0x800d
14 packets captured
Any hints, tips, clues?
--
Fredrik Rambris <[EMAIL PROTECTED]>
Advanced Systems Specialist
CDON.COM Nelly.com LinusLotta.com Gymgrossisten.com
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]